HDR-1 GB Version 1
HD Radio™ Technology Manufactured Under License From iBiquity Digital Corporation. iBiquity Digital and the HD Radio and HD logos are registered trademarks of iBiquity Digital Corporation. HD RadioTM is a trademark of iBiquity Digital Corporation. U.S. and Foreign Patents. 20070524_HDR-1_381QB0SB-A_GB.
Important Safety Instructions 1. Read these instructions. 10. Only use attachments/accessories specified by the manufacturer. 2. Keep these instructions. 11. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 3. Heed all warnings 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7.
Unit Controls (Front) 1. LCD display 2. Standby LED indicator 3. Remote Control Sensor 4. Power and Control knob 3 20070524_HDR-1_381QB0SB-A_GB.
Unit Controls (Rear) 5. FM Telescopic Antenna 6. AC power cord socket 7. Music and News selection switch 8. Headphone socket 9. Aux In socket 10. External AM Loop antenna socket 4 20070524_HDR-1_381QB0SB-A_GB.
Remote Control 1. 2. 3. 4. 5. 6. Power Information button ATS and Setup button Band selection Mute button Number buttons 7. 8. 9. 10. 11. 12. Audio Equalizer selection Last station recall HD Radio Seek button Tuning Control Volume Control Execution button 5 20070524_HDR-1_381QB0SB-A_GB.
Accessories Detachable power Cord x 1 FM Dipole Antenna x 1 AM Loop antenna x 1 Remote control unit x 1 Instruction manual x 1 Warranty card x 1 6 20070524_HDR-1_381QB0SB-A_GB.
Getting started First find a location for your new HD radio, 1. The FM telescopic antenna is already installed. Dipole Antenna and installing tool are in cluded for better reseption. 4. Plug the other hand of the AC power cord into a wall socket and switch on the wall socket if needed. (NOTE: You may hear a loud “POP” when power is connected. Do not be alarmed.) 2. Connect the AM loop antenna into external AM loop antenna terminal on the back of the unit. Important: 1.
Radio Controls Selecting the radio band/Auxiliary Input 1. To turn the radio on press the “Power” button on the remote control or hold “Power /Control knob” on the unit for 2 seconds. 2. To turn the radio off press the “Power” button on the remote control or hold “Power /Control knob” on the unit for 2 seconds. (NOTE: In standby mode, the tuner will display the time, dim the backlight (in 12 seconds) and standby LED will be on. 3.
Volume Control Using the Remote: 1. Press “Volume” Up/Down button until you reach desired volume. Using the Unit: 1. Rotate the “Power/Control knob” unit desired volume is reached. Mute Using the Remote: 1. Press MUTE button on the remote control to mute the radio. Press the MUTE button again to turn on the volume. Using the Unit: 1. Rotate “Power/Control knob” until volume is muted. Audio Equalizer (EQ) Using the Remote: 1. Press the “EQ” button until desired EQ setting is reached. Using the Unit: 1.
Listening to HD Radio When HD Radio station is found, display will show, 1. Station call sign. 2. The number of the multicasting program (1= main program). 3. The total number of HD Radio program services and HD Radio mark. 4. The preset number of this program. 5. The radio band.
Display Modes (INFO) There are several display modes. Please refer to the HDR-1 Menu Structure Table for a complete listing and description of these display modes. Using the Remote: 1. Press “Info” button. 2. Continually press “Info” button or press “Tune” Up/Down button to navigate through available display modes. Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Info” menu option. 2. Press “Power/Control knob” to select.
Advanced Information There are several Advanced Display modes. Please refer to the HDR-1 Menu Structure Table for a complete listing and description of these display modes. Using the Remote: 1. Press and hold “Info” button. 2. Continually press “Info” button to navigate through available display modes. Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Ad. Info” menu option. 2. Press “Power/Control knob” to select. 3.
Hybrid Seek Using the Remote: 1. Press the “SEEK” Up/Down button to seek the next frequency broadcasting in a usable radio signal. Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SEEK” menu option. 2. Press “Power/Control knob” to select. 3. Rotate “Power/Control knob” to select “Up” or “Down” direction. 4. Press “Power/Control knob” to select. 13 20070524_HDR-1_381QB0SB-A_GB.
ATS – Auto Tuning System The ATS function will scan through the selected band frequency for all usable signals. It will create an easily navigated table for all detected signals. Using the Remote: 1. Press and hold “ATS” button to activate menu. 2. Press “Enter” button to activate frequency scanning. 3. Allow radio to finish scanning. Once completed you can navigate through the available stations using the “Tune” Up/Down buttons.
Setting and Recalling Memory Presets Preset stations There are 10 preset stations each for AM and FM. Setting Memory Presets Using the Remote: 1. Press “Band” button to select desired band. 2. Hold corresponding numbered button for 2 seconds to store. i.e. to store 93.1 into memory position 2 press and hold the “#2” button on the remote. Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SET PRESET” menu option. 2.
Last Recall Station Using Remote: 1. Press LAST RECALL button on the remote control to recall last listening station. Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “RECALL” menu option. 2. Press “Power/Control knob” to select. Setting Sleep timer This unit comes with an adjustable sleep timer. This function can only be activated when the unit is on. Using the Remote: 1.
Auto clock function If the FM station you are listening to providing RDS service and has Auto clock time setting feature ( CT ). You can set the clock to be Auto clock, the clock will be automatically adjusted by the station RDS – CT service. Note: Before you set the Auto clock function, please make sure the FM station you tune to providing auto clock time setting service. The Auto clock function can be set only when radio Power is on. 1.
Turning Alarms On/Off & Setting This unit features a dual alarm system that can sound either to a beeping tone or AM/FM or Auxiliary Audio. The easiest way to set the alarms is when the unit is off, and these instructions are designed using this option. Using the Remote: 1. Press and hold “ATS/Setup” button to activate menu. 2. Continue to press “ATS” button or “Tune” Up/Down button to reach desired alarm (Alarm-1 or Alarm-2). 3. Press “Enter” to select. 4.
Using the Unit: 1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at desired alarm (Alarm-1 or Alarm 2). 2. Press “Power/Control knob” to select. 3. Rotate “Power/Control knob” to select the desired alarm setting (Beep, AM, FM, Auxiliary, OFF). 4. If turning off, press “Power/Control knob” to save. For all others press “Power/Control knob” and proceed to next step. 5. Set appropriate time.
Snooze function Canceling alarms The alarm will sound at the selected alarm time. Press any button except Power (Standby) button can be silence for 5 minutes interval until alarm is on again (Snooze). This sequence can be repeated during the alarm period. The alarm will activate for 60 minutes (30 minutes for Beep alarm) until you press Power button to cancel it. Display will appear Snooze and remaining time to next alarm on. Press Power button to cancel the Snooze.
Change Hour format You can change 12 hours time format into 24 hours format and vice versa. 1. Long press ATS/SET UP button until display appears SET UP and flashing ATS. 2. Repeatedly press and release ATS/SET UP button to get Hour Mode. 3. Press Execution button to enter Hour mode adjustment. 4. Press Tuning Up or Down button to get change required hour format. 5. Press Execution button again to complete setting.
RESET the radio Specifications If the radio fails to operate correctly i.e. display can’t change according to the operation. Unplug the AC power cord and wait for 5 seconds then re-plug. This is to reset the radio for troubleshooting the possible CPU power down. After RESET the radio, radio will be back to Standby mode (Power off) Power Requirement: Mains AC 120 volts 60 Hz only Battery (remote control) 3.0V CR 2025 button type Headphone socket A 3.
Brief User Interface: NO Button 0 any keys 1 2 Standby Power OFF Rotary Knob 4 Band 6 HDR1 function Snooze ON Power ON / Standby toggle click status Alarm ON Standby / Power ON Alarm ON / Snooze ON Standby click long 2s left right click click Power ON Power ON Power ON Power ON Power ON Power OFF long 2s Power ON click Power ON To go into frequency Tune mode to change frequency.
7 Preset 0~9 click long 2s click long hold click click long 0.5 s Power ON Power ON Power ON Power ON Power ON Power ON Power ON 11 HD seek 12 Execution click Click Click Power ON Power ON Power ON Go to Preset 0~9 Store Preset 0~9 VOLUME VOLUME fast Toggle Mute ON / OFF Tune next frequency step. Auto seek and go to the next station. (include analog and HD stations) Auto seek and go to the next HD station.
