WFR-70 GB Version 1
"Made for iPod," "Made for iPhone," and "Made for iPad" mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
Contents Introduction ...................................................................................... 3-7 Before you can use this product ...................................................... 3 Controls and connections ................................................................... 4 Navigation controls ............................................................................ 5 Network configuration ...................................................................
3 Before you can use this product Using the AC power adaptor Before you can use your internet radio, you must have the following: ● A broadband Internet connection (not required for DAB, FM or Music Player functions). ● A wireless access point (WiFi) connection connected to your broadband Internet Service Provider, preferably via a router.
Controls and connections 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Navigation controls This page describes the basic means of controlling your WFR-70 internet radio. Instructions for each operating mode are given in the later section of this book. 1. Pressing the Standby button brings your radio out of Standby mode. Pressing Standby while the radio is in use will cause it to return to the Standby mode with the clock display. 2.
Configuration Connecting your radio to your computer network 1. Place your radio on a flat surface and plug the mains lead into the mains socket located on the rear of your radio ensuring that the plug is pushed fully into the socket. 2. Plug the other end of the mains lead into the wall socket and switch on the wall socket. IMPORTANT: The mains plug is used as the means of connecting the radio to the mains supply. The mains socket used for the radio must remain accessible during normal use.
. You will then need to set 'Keep network connected.' By default, your radio will shut down its WiFi connection when it is in standby. This minimizes power consumption but it does mean that you will need to switch that radio on manually in order to use either the 'Play to' function or any other remote control software.
12. Rotate the Tuning Control Rotary to see the SSID for each wireless network that has been found. If your network is shown proceed to step 14. If it is not shown then proceed to step 13. If you make a mistake at any point, use the Back button to go back to the previous screen. 13. If your network is not found, it may be because the router is configured not to broadcast the SSID.
17. To enter the WEP or WPA key, characters are selected and entered using the Tuning Control Rotary. The highlight scrolls through the available characters as well as the three controls on the right. The character currently highlighted will be entered when you press the Tuning Control Rotary. Do this as needed until the complete key has been entered. Remember, WEP keys only use the numbers 0-9 and letters A-F. WPA keys are sensitive to upper and lower case characters.
Changing the network connection In the sections above, you chose how your radio would be connected to your network, using a WiFi connection. From time to time, you may find that you need to connect to different computer networks. The Internet setup menu allows you to change your radio’s network settings, scan for an alternative wireless network, or to manually configure the network parameters. The steps outlined below describe how you can do this –see also the section ‘Network Profiles’.
11 3. The manually specified IP address should be chosen to be compatible with the settings in your router and must be a unique address on your network. If you are using DHCP for some devices and static (manually configured) IP addresses for others, the IP address used should fall outside the range that the router may allocate using DHCP. Typically, the first three groups of digits will be the same for all devices on your network.
8. If you chose ‘Pre-Shared Key’ in step 7, you should then choose the WEP option. The key should be entered using only the numbers 0-9 and the letters A-F. The key will be 10 characters long for 64-bit encryption and 26 characters long for 128-bit encryption. The radio will accept lower-case letters a-f as equivalent to upper-case A-F. Spaces or special symbols are not permitted in WEP keys.
Network remote control options Network Pin setup (Pin number) Your radio has the option of being controlled by an application installed on an Apple iPhone, iPod touch or iPod. The Pin number facility allows you to ensure that your radio can only be controlled by your own Apple device rather than someone else’s. The remote control application is called UNDOK and is available from the Apple App Store and Google Play Store for your device.
Selecting a radio station by location 1. Press the Standby button to switch the radio on. Then press the Mode button and rotate the Tuning Control Rotary to highlight the internet radio mode display. Press the Tuning Control Rotary to select the option. 2. Press the Menu button to enter the main Internet radio menu. Rotate the Tuning Control Rotary until ‘Station list’ is highlighted on the display and then press the Tuning Control Rotary to select the option. 3.
8. Rotate the Tuning Control Rotary to highlight your chosen radio station and then press the Tuning Control Rotary to enter your selection. The display will show ‘Connecting…’ while the radio connects to the new station. The station should then start playing. Adjust the volume as needed. 9.
Selecting a radio station by genre 1. Press the Menu button to enter the main Internet radio menu. Rotate the Tuning Control Rotary until 'Station list' is highlighted on the display and press the Tuning Control Rotary. 2. Rotate the Tuning Control Rotary until ‘Stations’ is highlighted on the display and then press the Tuning Control Rotary to select. 3. Rotate the Tuning Control Rotary until ‘Genre’ is highlighted on the display and then press the Tuning Control Rotary. 4.
Searching for a radio station by name There may be occasions when you know the name of a radio station but you do not know the location or genre. This facility allows you to search for the station using a part (or parts) of the radio station name. 1. Press the Menu button to enter the main Internet radio menu. Rotate the Tuning Control Rotary until ‘Station list’ is highlighted on the display and then press the Tuning Control Rotary. 2.
Selecting a new or popular station As described in the section ‘Internet Radio – the basics’, your radio connects via the the Internet to a database of radio stations. This option is provided to highlight stations which are newly added to the list of those available, or stations which are particularly popular with listeners around the world. Your radio allows you to easily choose stations from these two categories, using menus very similar to those used when finding stations by location and genre. 1.
Selecting a podcast / BBC Listen Again Some radio stations allow you to listen to programs that have already been broadcast. The BBC’s Listen Again service is an example of this. In addition, radio broadcasters and individuals may make programs which are intended normally to be downloaded into a computer or copied onto a portable media player. These are commonly known as Podcasts.
Presetting stations With so many Internet radio stations available, it is desirable to have a means of rapidly selecting the stations that you listen to most frequently. Your radio has five memory presets which can easily be set to store the details of any Internet radio station. The radio station presets are retained in memory even when the radio is switched off. Please see also the section ‘Last Listened’ and ‘Configuring My Favorite Stations’. GB Storing a preset 1.
Last Listened It is often helpful to be able to go back to a station that you have already listened to. Your radio has a ‘Last Listened’ feature which provides you with quick access to the ten most recently listened to radio stations or podcasts. As each new radio station is listened to the oldest item is deleted from the list. The Last Listened list is stored when the radio is disconnected from the mains. 1. With the radio switched on and in Internet radio mode, press the Menu button.
Display modes Your radio has a range of display options when in Internet Radio mode. Note that not all information may be available for all Internet radio stations. 1. Press the Info button to cycle through the different options. a. Description b. Genre c. Reliability d. Format e. Playback buffer f . Date Displays information about the radio station or scrolling text messages such as artist/track name, phone number etc. Displays program type information e.g. Pop, Classic, News, etc.
Customizing your radio In addition to storing your favourite radio stations in the radio presets, your radio allows you to create customised lists of stations which can appear in two special menus on the radio called 'My Favourites' and 'My Added Stations'. Your radio uses a database which is accessed via the Internet in order to find out which radio stations are available and how it should connect to them. You are able to add your personal selections to this database.
Configuring My Favorite Stations Configuring My Added Stations 1. Using the website at http://www.wifiradio-frontier.com it is possible to search among the many radio stations that are available by location, genre, or language. You may also choose from new or popular stations. 2. When the radio stations that you have found are shown on your computer screen, they are shown with a 'Play' icon and an 'Add to favourites' icon (the plus symbol and heart).
Selecting your favorite stations 1. Press the Menu button to enter the main Internet radio menu. 2. Press the Tuning Control Rotary until 'Station list' is highlighted on the display. Press the Tuning Control Rotary to enter the menu. 3. Rotate the Tuning Control Rotary until 'My Favourites' is highlighted on the display. Press the Tuning Control Rotary and your favorite stations list will appear on the display (set up as described on the preceding page). 4.
Selecting your added stations 1. Press the Menu button to enter the main Internet radio menu. Rotate the Tuning Control Rotary until 'Station list' is highlighted on the display and then press the Tuning Control Rotary to select. 2. Rotate the Tuning Control Rotary until 'My Added Stations' is highlighted on the display and then press the Tuning Control Rotary to select. 3.
Music player Use with Windows, Apple Mac and Linux The Music Player allows you to play audio files which are stored on computer in your network. In order to play fi les from a computer on your network, your radio must connect to a fi le server program on your computer which uses the Universal Plug and Play (UPnP) protocol (often known as DLNA). If your computer uses Windows 7 or Windows 8 then your computer already has a UPnP server program available.
Accessing your audio files via a UPnP server If your computer is running Windows 7 or 8, then Windows Media Player version 12 includes a UPnP server which will make your files available to your radio. If you have Windows Vista or XP (Please refer to the section of ‘Accessing your audio files via a UPnP server using Windows Vista and XP’). There are other UPnP server solutions available for non-Windows users and for Windows users who may wish to use an alternative (see the preceding section).
4. Rotate the Tuning Control Rotary until 'Shared media' is highlighted and press the Tuning Control Rotary to select. The radio will scan for all available UPnP servers. It may take a few seconds for the radio to complete its scan. The radio will display '' if no UPnP servers are found. 5. After scanning, select your UPnP server using the Tuning Control Rotary on the panel. If you allowed automatic connection previously, your radio should now connect and you may skip to the next page.
Locating and playing media files using UPnP Once the UPnP server has been configured to share media files with your radio, you may select the files that you wish to play as follows:1. Press the Standby button to switch on the unit. Press the Mode button and rotate the Tuning Control Rotary as needed until the Music Player mode display is shown. Then press the Tuning Control Rotary. The main Music Player menu will then be displayed. 2.
Media selection When searching via UPnP you will have a selection of search criteria as determined by the UPnP server software on your computer. This allows you to search by a given information type (Album, Artist, Genre, etc.) and then to narrow the search to an album or to a particular track within an album. Some UPnP server applications allow the search options to be customized. The searches described here are just examples of the possibilities. Listening to a complete album 1.
Listening to a particular track 1. If you wish to play only a particular track from an album or folder, first choose the album or folder as described on the preceding pages. 2. Rotate the Tuning Control Rotary until the required track is highlighted. 3. Press and release the Tuning Control Rotary. The track will begin playing. The radio will then play subsequent tracks from the same album or folder. Controlling playback 1. Press the Play/Pause button to pause playback of the current track. 2.
Repeat tracks 1. When a track is playing , press the Menu button to enter the main Music player menu. 2. Rotate the Tuning Control Rotary until ‘Repeat play’ is highlighted on the display. Press the Tuning Control Rotary to turn on the repeat function. Your selected track will be played repeatedly and the repeat indicator will show on the display. 3. To turn off the repeat option, select the ‘Repeat Play’ again. Music player Love Me Do Artist: The Beatles 12:34 UPnP Shuffle tracks 1.
Display modes Your radio has a range of display options when in Music Player mode. Note that the availability of information depends on the specific media files, their format and upon the server capability. (Not all UPnP servers make information from the media files available in the same way.) 1. Press the Info button to cycle through the different options. a. Progress bar b. Artist c. Album d. Format e. Buffer Displays the playback progress for the track currently playing.
Playlists Sometimes you may wish to set up a list of music tracks or albums which can then be played without further action - as background music for a party, for example. Your radio can be configured to hold a queue of up to 500 tracks in a playlist menu. The tracks or albums for the playlist can be selected from your UPnP server. The playlist is held in memory in your radio until external power is removed, or until the playlist is cleared from the menu. Adding a single track to your playlist 1.
Viewing your playlist 1. Press the Standby button to switch on the unit. Press the Mode button and rotate the Tuning Control Rotary as needed until the Music Player mode display is shown. Then press the Tuning Control Rotary. The Music Player menu will then be shown on the display. 2. Rotate the Tuning Control Rotary until 'My Playlist' is highlighted on the display. Press the Tuning Control Rotary button to enter the playlist. 3. Rotate the Tuning Control Rotary to scroll through the playlist.
Clearing the playlist 1. Press the Menu button to enter the main Music Player menu. 2. To clear the whole playlist press the Tuning Control Rotary until 'Clear My playlist' is highlighted on the display. Press the Tuning Control Rotary. 3. To clear the whole playlist rotate the Tuning Control until 'YES' is highlighted on the display. Press the Tuning Control Rotary to cause the playlist to be cleared. 4.
Wake On LAN If you use a computer as a UPnP server for playing your music files via your radio, you may not wish to keep that computer running when you are not using the radio. If your computer is suitably configured, it can either shut down, or enter a standby or hibernation state when it is not being used. Your radio can wake up a computer which has shut down using a Wake On LAN command via the network provided that the radio has previously connected to a UPnP server application on that computer.
Keep network connected Keep network connected By default, your radio will shut down its WiFi connection when it is in standby. This minimizes power consumption but it does mean that you will need to switch that radio on manually in order to use either the ‘Play to’ function or any other remote control software.
6. Windows will then open a ‘Play to’ window showing the track or tracks to be played. Your computer will then take control of your radio. Your radio will then enter the Digital Media Renderer mode (DMR) and after a few seconds the radio will start playing. The display on the radio will show that it is in DMR mode. 7.
Using USB memory devices This section describes how to use your radio to access and playback your audio files via USB memory devices. USB slots are located on rear of the unit. Important: Your radio is only designed to work with USB memory flash memory devices. It is not intended to be connected to hard disk drives or any other type of USB device. It is possible to use SD or SDHC cards for media storage and playback when held in a suitable USB adaptor.
Playing files from USB memory devices Inserting and removing memory devices 1. Carefully insert the USB memory device into the USB slot. Press the Standby button to switch on the radio. The radio may detect the memory has been connected in which case it will ask whether you wish to open the folder view of the memory contents.Press the Tuning Control Rotary to select ‘Yes’ and skip to step 4 below. If the USB memory was not automatically detected, proceed as follows. 2.
DAB Radio Using DAB mode for the first time 1. Carefully extend the telescopic aerial. 2. Press the Standby button to switch on the radio. If the radio has been used before the last used mode will be selected. 3. Press the Mode button and rotate the Tuning control Rotary as needed so that DAB radio mode is selected on the display. Press the Tuning Control Rotary to select the option. 4. If this is the first time that DAB mode is used a quick scan of the Band III DAB channels will be carried out.
Selecting a DAB radio station 1. When playing a DAB radio station, the display normally shows the name of the current station with other related information. 2. Rotate the Tuning Control Rotary to access the radio station list and to scroll through the available stations. 3. Press the Tuning Control Rotary to select the highlighted station. The display may show 'Connecting...' while the radio re-tunes. 4. Use the Volume control knob to set the sound level as needed.
Display modes Your radio has a range of display options when in DAB mode:1. Press the Info button to cycle through the different options. a. Text b. Program Type c. Multiplex Name/Frequency d. Signal error/strength e. Bit rate and audio type f . Date Displays text messages such as the artist or track name, phone in number, traffic alerts, etc. Displays the type of station being listened to such as Pop, Classic, News etc.
Finding new DAB radio stations Should you wish to use your radio for DAB reception in a new location, or if no stations were detected during the initial scan, you can follow this procedure to allow your radio to find out which DAB radio stations are available. 1. Ensure that the telescopic antenna is extended, and then press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB radio mode. Press the Tuning Control Rotary to select the option. 2.
Dynamic Range Control setting Dynamic Range Control (also known as DRC) can make quieter sounds easier to hear when your radio is used in a noisy environment by reducing the dynamic range of the audio signal. 1. Press the Standby button to switch on your radio. 2. Press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB radio mode. Press the Tuning Control to select the option. 3. Press the Menu button to enter the DAB menu. 4.
Station order setup Your radio has 3 station order settings from which you can choose. The station order settings are, alphanumeric, ensemble and valid. Note: The default station order on your radio is alphanumeric. 1. Press the Standby button to switch on your radio. 2. Press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB radio mode. Press the Tuning Control Rotary to select the option. 3. Press the Menu button to enter the DAB menu list. 4.
Prune stations If you move to a different part of the country, some of the stations which were listed may no longer be available. Also, from time to time, some DAB services may stop broadcasting, or may change location or frequency. Stations which cannot be found, or which have not been received for a very long time are shown in the station list with a question mark. The Prune stations function will delete the marked DAB stations from your station list. 1. Press the Standby button to switch on your radio.
FM Radio Operating your radio in FM mode 1. Carefully extend the telescopic aerial and press the Standby button to switch on your radio. 2. Press the Mode button and rotate the Tuning Control Rotary as needed to highlight FM radio mode. Press the Tuning Control Rotary to select the option. 3. Rotate the Tuning Control Rotary in a clockwise direction. The displayed frequency will increase. Press the Tuning Control Rotary to carry out an auto-tune.
Display modes Your radio has a range of display options when in FM mode:1. Press the Info button to cycle through the different options. a. Text b. Program Type c. Frequency d. Date Displays text messages such as the artist or track name, phone in number, traffic alerts, etc. Displays the type of station being listened to such as Pop, Classic, News etc. Displays the frequency of the FM signal. Displays the current date.
Scan setting When using the FM mode your radio can be set to either scan local stations or to scan all stations including distant radio stations. 1. Press the Mode button and rotate the Tuning Control Rotary as needed to highlight FM radio mode. Press the Tuning Control Rotary to select the option. 2. Press the Menu button to enter the FM menu. 3. Rotate the Tuning Control Rotary until 'Scan setting' is highlighted and then press the Tuning Control Rotary to enter the scan adjustment mode.
Stereo / Mono switching If the FM radio station being listened to has a weak signal, some hiss may be audible. It is possible to reduce this hiss by forcing the radio to play the station in mono rather than stereo. 1. Press the Mode button. Rotate and press the Tuning Control Rotary as needed to select the FM radio mode display and tune to the required FM station as previously described. 2. Press the Menu button to enter the FM menu. 3.
Presetting stations in DAB and FM modes There are 5 memory presets each for DAB and FM radio. They are used in the same way for each operating mode. 1. Press the Standby button to switch on your radio. 2. Tune to the required radio station as previously described. 3. To store the station as a preset, press and hold the required Preset button (1-5) until the display shows 'Preset stored'. The station will be stored under the chosen preset button. Repeat this procedure as needed for the remaining presets.
Listening to Spotify Playing music using Spotify Connect Introduce your radio to a whole new world of music. With Spotify, you can enjoy instant access to millions of songs A Spotify Premium subscription is required. For details, see the Spotify homepage. http://www.spotify.com The Spotify software is subject to third party licenses found here: www.spotify.com/connect/third-party-licenses 1. Prepare for playback ● Download Spotify app ( ) to your smartphone or tablet and log in to the app.
4 Play tracks via your radio. Press the Connect icon at the bottom right corner of the screen and you should find your radio on the list. Press the item and your smartphone/tablet is linked with your radio (e.g. WFR-70). You can see the green Connect icon indicating the connect is on radio. Now you can listen to audio streamed wirelessly from your linked smartphone/ tablet. Note: If you cannot see the icon, it indicates no connect device available.
Display mode- Spotify Connect Your radio has a range of display options when playing Spotify Connect. Press the Info button to cycle through the different options a. Progress bar Displays the playback progress for the track currently playing b. Artist Displays the name of the artist for the track currently playing c. Album Displays the name of the album from which the current track is taken. d. Bit rate Displays the bit rate and sampling rate of the track currently playing e.
Streaming data rate - Spotify Connect Your radio can change different music streaming quality when you stream content from Spotify. If your internet connection has a low data usage allowance, or has a relatively low maximum data rate, it is strongly suggested that your radio uses a lower streaming quality (data rate) for Spotify connections. In some cases this may allow more reliable streaming, although some loss of audio quality will occur.
Multi-room This radio is part of Sangean SmartLink multiroom series. This series has ‘Multi-room’ feature allowing the same music to be played simultaneously through Sangean SmartLink Series (i.e. multiroom capable devices) with users being able to share music on their home network and also from Spotify, Internet radio and other music source. In this home network, multi-room capable devices can be treated as individual or orgnised into synchronized groups.
8. To ensure you can use UNDOK app when your radio is in all modes especially in non-internet modes (i.e. in DAB, FM, Bluetooth or Aux in mode) you need to select “Yes” in ‘Keep Network Connected’ menu. This also allows you to wake the radio from standby using your UNDOK app. Note: If unattended to use radio for long periods of time, e.g. overnight, while on holiday or while out of the house, select NO to save power is recommended. 9.
Clock and Alarms Automatically updating the clock Your radio will normally update the clock automatically when connected to the internet. If you enter a time setting manually, the radio will calculate a local time offset which is then stored in memory. Whenever it synchronizes the clock using the internet, including after a power failure, your radio will then set the clock automatically using this information.
Setting the clock format The clock display used in standby mode and on the playing mode screens can be set to 12 or 24 hour format. The selected format is then also used when setting the alarms. 1. With your radio switched on, press the Menu button to access the menu for the current mode. 2. Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press the Tuning Control Rotary to enter the system settings menu. 3.
Manually setting the clock The WFR-70 radio will normally set its clock automatically to local time after a connection to the Internet has been established. Should you need to set the time manually, change the time zone, or manually switch from winter to summer time (GMT to BST - also known as daylight savings time), then please follow this procedure. 1. Press the Standby button to switch on your radio. 2. To set all time settings press the Menu button to access the menu for the current mode. 3.
8. Rotate the Tuning Control Rotary to select the correct year. Press the Tuning Control Rotary to enter the selection. The hour digits will then flash. 9. Rotate the Tuning Control Rotary to select the correct hour. Press the Tuning Control Rotary to enter the selection. The minute digits will then flash. 10. Rotate the Tuning Control Rotary to select the correct minutes. Press the Tuning Control Rotary to enter the selection. The display will then return to the previous menu. 11.
Setting the alarm clock Your radio has two separate alarms which can be set to wake you to either the radio, USB or a buzzer alarm. In the event of a power interruption your radio has built in memory that will retain your alarm settings. Ensure that the time is set correctly before setting the alarms. 1. Press the Menu button and rotate the Tuning Control Rotary until ‘Main menu’ is highlighted. Press the Tuning Control Rotary to enter the menu. 2.
Setting the alarm clock - cont. 7. Rotate the Tuning Control Rotary to highlight 'Enable' and press the Tuning Control Rotary. The display will show the Frequency options for the alarm.
Setting the alarm clock - cont. 10. Rotate the Tuning Control Rotary until the 'Volume:' option is highlighted on the display and press the Tuning Control Rotary if you wish to change it. The radio uses the saved volume setting for each alarm when it sounds. Set the required volume using the Tuning Control Rotary to confirm the setting. 11. I n order to store the alarm settings rotate the Tuning Control Rotary until 'Save' is highlighted. Press the Tuning Control Rotary to store the alarm settings.
When the alarm sounds The buzzer or radio alarm will sound at the selected times for up to 60 minutes unless cancelled. The volume used for the alarm will be as specified during the alarm setting procedure. If the radio cannot connect to the specified radio station, the buzzer alarm will be used instead. To cancel an alarm, press the Standby button to return to standby mode.
Snooze timer 1. The buzzer or radio alarm can be silenced for 5 minutes by pressing any button other than the Standby button. Should you wish for a longer snooze duration this can be extended. Press and rotate the Tuning Rotary Control while the radio is snoozed will set the available snooze time to 5, 10, 15 or 30 minutes. 2. While the snooze timer is active the remaining snooze time is shown next to the flashing alarm icon on the clock display. 3.
Inactive standby Your radio can be set to standby mode automatically if it idles for a preset period of time. The idle time setting can be adjusted between 2, 4, 5 and 6 hours. 1. Press the Menu button and rotate the Tuning control Rotary until 'System Settings' is highlighted. Press the Tuning Control Rotary to enter the menu. 2. Rotate the Tuning Control Rotary until 'Inactive Standby' is highlighted. Press the Tuning Control Rotary to enter the setup. Options for idle time will appear on the display.
Display and Audio Equalizer function The sound on your radio can be adjusted to suit your personal taste for the material that you are listening to. The WFR-70 has a range of equalizer modes. Alternatively you may set the treble and bass levels to your own preferences which can be accessed from the My EQ menu item. 1. Press the Menu button and rotate the Tuning Control Rotary until ‘System settings’ is highlighted. Press the Tuning Control Rotary to enter the setup. 2.
Setting up your My EQ profile If you find the preset equalizer functions not to your liking, you may set up a custom treble and bass setting as follows: 1. Follow steps 1-2 in the previous section in order to enter the Equalizer menu. 2. Rotate the Tuning Control Rotary until 'My EQ profile setup' is highlighted on the display. Press the Tuning Control Rotary to enter the adjustment mode. 3. To adjust the bass level rotate the Tuning Control Rotary until 'Bass' is highlighted on the display.
Brightness control The brightness of the display can be adjusted for when the radio is in standby and for when it is in use. If you use the unit in the bedroom, you may prefer a lower standby brightness level than a higher brightness setting. 1. Press the Standby button to switch on your radio. Access the menu for the current mode by pressing the Menu button. 2. Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display.
Headphone socket A 3.5mm Headphone Socket located on the rear of your radio is provided for use with headphones. Inserting a plug automatically mutes the internal loudspeaker. Please be aware that the sensitivity of headphones can vary widely. We therefore recommend setting volume to a low level before connecting headphones to the radio. It is also recommended to reduce the volume before unplugging your headphones. IMPORTANT: Excessive sound pressure from earphones and headphones can cause hearing loss.
Auxiliary input socket A 3.5mm Auxiliary Input socket located on the rear of your radio is provided for connecting the audio signal from an external audio source such as an MP3 or CD player. 1. Connect a stereo lead from the headphone output of your MP3 or CD player to the Aux In socket located on the rear of your radio. Typically this lead will have a 3.5mm stereo plug at both ends. 2. Switch on your radio. 3.
Information Factory reset If you wish to completely reset your radio to its initial state this may be performed by following this procedure. By performing a factory reset, all user entered settings will be erased. 1. Access the menu for the current mode by pressing the Menu button. Rotate the Tuning Control Rotary to highlight the 'Main menu' option, then press the Tuning Control Rotary to confirm. 2.
Software update From time to time, new software features for your radio may be developed. Your radio has therefore been designed to allow its internal software to be updated using your Internet connection. You should not attempt to update your radio unless it is recommended to you by Sangean Customer Services. Updating the software may remove all network settings, radio station presets and alarm settings from your radio.
Network profiles Each time that you connect your radio to a WiFi network, the radio will store the details of that connection (SSID, security key, DHCP/IP address settings) as a profile. Up to four such profiles are stored in the radio so that if the unit is used in multiple locations there is no need to enter the network settings when returning to a location previously visited. The radios stores the four most recent profiles in memory identified by their SSID.
Software version display The software version display is provided for reference and customer support purposes and cannot be changed. 1. Access the menu for the current mode by pressing the Menu button. Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press the Tuning Control Rotary to enter the System settings menu. 2. Rotate the Tuning Control Rotary until 'Info' is highlighted on the display.
Accessing your audio files via a UPnP server using Windows Vista and XP Set up UPnP access on a Windows PC - cont. If your computer is running Windows Vista or XP, then Windows Media Player version 11 includes a UPnP server which will make your files available to your radio. There are other UPnP server solutions available for non-Windows users and for Windows users who may wish to use an alternative (see the section of Use with Windows, Apple Mac and Linux).
Audio codecs Bit-Rates Your radio supports a range of audio codecs which provide compatibility with a wide range of Internet Radio stations. These also allow users to stream music from their computers or to play directly from USB and SD/ SDHC fl ash memory devices. Note that for any given audio codec, there are many streaming protocols available, and thus even if an Internet Radio station uses a supported format, this does not guarantee that every such station will work with your radio.
Cautions Do not allow your radio to be exposed to water, steam or sand. Do not leave your radio where excessive heat could cause damage. The name plate is located on the rear of the radio. ● T he radio shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the radio. ● I t is recommended to operate the product such that there is a minimum distance (10cm recommended) to adjacent objects in order to ensure good ventilation.
Specifications Circuit features Power Requirements Output power Headphone socket Aux In socket Line Out socket Aerial System Mains Power Supply AC 100-240 V/50/60 Hz/1A Frequency Coverage FM DAB WiFi 87.5-108 MHz 174.928-239.200 MHz 802.11b and 802.11g supported with WEP and WPA/WPA2 encryption Compatible with 802.11n routers which offer mixed Maximum supplying power of USB socket: 5W+5W(If connected with SP-40 speaker) 3.5 mm diameter, stereo 3.5mm diameter, stereo 3.
