WR-12BT 中文 GB Version 1
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. GB 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel.
17. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall not be placed on the apparatus. GB 18. Excessive sound pressure on ear- and headphones could impair the hearing ability. Higher setting that idle on the equalizer leads to higher signal voltages on the output for ear and headphones. 19.
Controls Power button 2 Band selecting rotary 3 Dial scale 4 Dial indicator 5 Dial marker 6 Volume control 7 Treble control 8 Bass control 9 Speaker 10 Tuning LED indicator 11 Tuning control 12 F-type external antenna terminal 13 AM external antenna terminal 14 Subwoofer speaker 15 AC main power switch 16 AC power cord socket 17 Dimmer control 18 Headphone socket 19 AUX IN socket 20 External / internal antenna switch 1 GB
Power your radio AC operation Before you plug the AC cord into the radio, make sure the AC voltage is correct. Insert the plug on the end of the supplied power cord into the AC power socket on the back of the radio and turn on the main power switch. Antenna setup for FM reception The radio comes with built-in AM/FM antenna and external antenna. To use FM internal antenna, make sure to switch FM external/ internal antenna switch in the back of your radio to internal antenna position (i.e. INT. FM ANTENNA).
Operating your radio FM 1. Make sure you have set up the FM antenna in advance and turn on the main power switch in the rear of the unit. GB 2. Press the power button located in the front panel. 3. Rotate the band selecting rotary to the FM (MONO) or ST(FM stereo). Note: If the FM radio station being listened to has a weak signal, some hiss may be audible. It is possible to reduce this hiss by forcing the radio to play the station in mono rather than stereo. 4.
Operating your radio AM 1. Press the power button located in the front panel. 2. Rotate the Tuning Control to select the desired station. In AM mode, the tuning scale is marked in kHz (Kilohertz). The tuning LED will appear brightest when best tuning has been achieved. 3. Rotate your radio for best reception. 4. Adjust the Volume Control for comfortable listening. 5. Press the power button to turn off the radio.
AUX IN socket Connect a stereo or mono audio source (like CD walkman, iPod or digital media music player) to this input to listen the audio program via the speaker. GB Dimmer control The brightness of the dial scale may be adjusted. If you use the unit in the bedroom, you may prefer a higher brightness level than the standard setting. Treble / Bass control The sound on your radio can be adjusted to suit your personal taste for the material that you are listening to.
Listening to Bluetooth music You need to pair your Bluetooth device with your radio before you can auto-link to play/stream Bluetooth music through your WR12BT. Paring creates a permanent `bond' so two devices can always recognize each other. Pairing your Bluetooth device 1. Rotate the Band selecting rotary to select Bluetooth function. The Bluetooth icon on the panel will flash within 3 second. 2. Activate Bluetooth on your device according to the device's user manual to link to your WR-12BT.
Note: If your Bluetooth-enabled device is temporarily disconnected to your WR-12BT. As long as the disconnection last within 7 minutes, your device can re-connect with your radio again automatically. If the disconnection last more than 7 minutes, then you need to manually reconnect your device again to the radio. Be aware that during the period of disconnection, no other Bluetooth device can pair or link with your radio.
Specifications AC Power: AC 120 V/60 Hz/50W (max) (US version) AC 230 V/50 Hz/50W (max) (European version) Frequency Coverage: FM 87.50 - 108 MHz AM 520 - 1710 kHz AUX-IN: 3.
Speaker: Stereo: 2.25inches 8 ohm x 2 Subwoofer: 3.5inches 8 ohm x 1 GB Headphones socket: 3.5 mm dia. Stereo jack Stereo output Output power: 3mW + 3mW (impedance 32ohm) The company reserves the right to amend the specification without notice. If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.