Instruction manual

ManualsBrandsSangean Manualsaudio & home theatreWR-3

2 Instruction manual

Important Safety Instructions

Read these instructions .

Keep these instructions .

Heed all warnings .

Follow all instructions .

Do not use this apparatus near water .

Clean only with dry cloth .

Do not block any ventilation openi

ngs . Install in accordance with the manufacturer

instruction .

Do not install near any heat sources such as radiators , heat registers , stoves, or other

apparatus ( including amplifiers ) that produce heat .

Do not defect the safety purpose of the polarized or grounding

type plug . A polarized plug

has two blades with one wider than the other . A grounding type plug has two blades and a

third grounding prong . The wide blade or the third prong are provided for your safety . If

the provided plus does not

fit into your outlet , consult an electrician for replacement of the

obsolete outlet .

10.

Protect the power cord from being walked on or pinches particularly at plugs ,

convenience receptacles , and the point where they exit from the apparatus .

11.

Only use at

tachments/accessories specified by the manufacturer .

12.

Use only with the cart , stand , tripod , bracket , or table specified by the manufacturer , or

sold with the apparatus . When a cart is used , use caution when moving the

cart/apparatus combination to

avoid injury from tip

over .

13.

Unplug this apparatus during lightning storms or when unused for long period of time .

14.

Refer all servicing to qualified service person . Servicing is required when the apparatus

has been damaged in anyway , such as power

supp

ly cord or plug is damaged , liquid has

been spoiled or objects have been fallen into the apparatus , the apparatus has been

exposed to rain or moisture , does not operate normally or has been dropped .

15.

To reduce the Risk of Fire or Electric Shock , do not

expose this appliance to rain or

moisture .

16.

The Shock Hazard Marking and Associated Graphical Symbol is provided on the rear

panel of unit .

17.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids ,

shall not be placed o

n the

apparatus

Summary of content (16 pages)

PAGE 1
WR-2 Instruction manual Important Safety Instructions 1. Read these instructions . 2. Keep these instructions . 3. Heed all warnings . 4. Follow all instructions . 5. Do not use this apparatus near water . 6. Clean only with dry cloth . 7. Do not block any ventilation openings . Install in accordance with the manufacturer s instruction . 8. Do not install near any heat sources such as radiators , heat registers , stoves, or other apparatus ( including amplifiers ) that produce heat . 9.
PAGE 2
Controls 1. Light button 2. Radio band/AUX IN selection 3. Memory presets 4. Power On/Off/Sleep button 5. Rotary Tuning Control 6. Volume/Tone control 7. IR sensor 8. Traffic information button and minute adjustment 9. Auto time button and hour adjustment 10. Alterative frequency and Select button 11. Set button 12. Display button 13. Station search and mono button 14.
PAGE 3
15. External F-type FM antenna terminal 16. External AM antenna terminal ( USA version only ) 17. AC power cord socket 18. 12V DC input socket ( ideal for vehicles/boats ) 19. REC out socket 20. Aux in socket 21.
PAGE 4
22. Reset button Display A. Frequency/Time/Station display B. Radio/Buzzer alarm symbol C. Daylight Saving Time ( DST ) , not applicable for WR-2 D. Sleep/Snooze status E. RDS indicator F. Time indicator G. Stereo indicator H. Traffic indicator I. J.
PAGE 5
Remote Control 1. Power on/off/Sleep button 2. Tuning control 3. Volume control 4. Tone control 5. Memory presets 6. Mute 7. Traffic button and minute adjustment 8. Auto time button and hour adjustment 9. Alternative Frequency and Select button 10. Set button 11. Display button 12.
PAGE 6
AC operation Before you plug the AC cord into the radio , be sure the AC voltage is correct . Insert the plug on the end of the supplied power cord into the AC power socket on the back of the radio . DC operation For outdoors use , you can power the radio by using 12V DC input socket from a DC power supply ( example , from the power supply of vehicles or boats ) . An AC power adaptor with 1 Ampere and center positive in polarity can also power the radio in house .
PAGE 7
Alarm can be operated when radio is on or off . Setting via remote control is the same . Wake to buzzer alarm A beep tone will sound when using the buzzer alarm . The alarm beep will increase in volume every 15 seconds for one minute followed by one minute silence before repeating the cycle . The buzzer alarm will sound for one hour unless turned off by pressing the On/Off button . Pressing the On/Off button whilst the alarm is sounding will cancel the alarm for 24 hours . 1.
PAGE 8
will flash or . 5. Press Band button and rotary tuning knob to select required radio station . You can also select alarm station by recalling the preset stations pressing memory presets button . 6. Press and release Set button to complete radio alarm set . Display will show radio alarm icon . 7. The volume level will be same as last radio station listening to . Monitor radio alarm station Note: remote control unit is not applicable for this operation 1. Ensure the radio is switched off . 2.
PAGE 9
through the available sleep times in the order 60-45-30-15-120-90-60 . Release the button when the required sleep time appears in the display and the radio will play the last station selected . 2. To cancel the sleep function , press On/Off button , the symbol will disappear . Display backlight To turn on display illumination , press and release Light button . By pressing and releasing Light button , you may also adjust display brightness or turn off the illumination completely .
PAGE 10
Scan tuning via remote control device 1. Switch on your radio by pressing the power button . 2. Select the required waveband . 3. Press and hold down either the tuning up or down button until the frequency in the display begins to change rapidly . Release the button . 4. Your radio will scan the selected the waveband , stopping each time it finds a station of sufficient strength . Adjust the volume control to the required level . Rotary manual tuning 1. Press the on/off button to switch on your radio . 2.
PAGE 11
level ( maximum to 60 ) 2. Press Volume control once to get into Treble control . Rotary the control until required treble is reached . 3. Press Volume control twice to get into Bass control . Rotary the control until required bass is reached . FM Stereo/Mono button 1. If a station being received is weak , some hiss may be audible . To reduce the hiss , press and hold down Mono button until radio beeps and display shows MONO . 2. Press and hold down the Mono button to return to Stereo operation . 3.
PAGE 12
1. Ensure that your radio is switched off . Press and hold down the M3 button until current clock format begins to appear in the display . Hold down the M3 button for another 8 seconds until clock format begins to flash in the display . 2. Rotary the tuning control to adjust required clock format ( rotary up to get 24 hours format and rotary down to get 12 hours format ) . 3. Press the M4 button again to complete setting . Display will return to clock status after setting .
PAGE 13
Operating your radio using RDS ( Radio Data System ) 1. Switch on your radio and select the FM waveband . 2. Tune into a station , the display will indicate frequency for a few seconds and then change to show the station name . The RDS symbol will appear in the display . 3. If the station does not carry RDS information only the station frequency will be shown . 4. The RDS symbol will flash if the signal is too weak for RDS operation .
PAGE 14
Display button Whilst tuned to a station , you can change between station name/frequency , normal time and alarm time ( if set ) by repeatedly pressing of the Display button . AUX IN socket On the rear of your radio is to allow signal from external device e.g. CD player to be fed into your radio and playback of the external device via your radio amplifier . Inserting a plug into the AUX IN will not mute the radio signal , however you have to long press the Band button for approx.
PAGE 15
1. Switch off the radio . 2. With the aid of a suitable implement ( the end of a paper clip ) , press the RESET button located on the underside of your radio for at least 2 seconds , this will reset the microprocessor , clock time and clear all stations stored in the preset memory . Mute the radio Press MUTE button on the remote control to mute the radio . Press MUTE button again or power on/off or volume control to release the muting .
PAGE 16