Installation Guide

ManualsBrandsSaniflo ManualsBathSaniStar 1-piece 1.28/1 GPF Dual Flush Elongated Toilet in White with Wall Carrier

MOUNTING THE BOWL AND

CUTTING OUT THE PANEL

IMPORTANT: Make sure to install the toilet

seat before mounting the bowl.

1 - When the frame is placed against a wall;

cut strips of cement board (or gypsum

board) to cover the sides and front of the

frame.

2 - When the frame is inside a wall, board the

entire opening.

- Note. Make a 1-inch (25 mm) hole in the

board (corresponding with the threaded

rods). This will allow you to adjust the

depth of the rod later.

IMPORTANT: Make sure to have an access

panel in order to minimize any extra work in

case of service.

- Place the template

against the wall,

positioning the holes for the WC supports

rods accordingly.

5 - Trace the inner shape of the template

onto the front.

- Remove the template

and cut out the

opening as traced, being careful not to

cut any pipe or wire.

- Note. If you are tilling the wall, the tiles

will have to be cut out in the shape of the

inner opening.

8 - Finish the support wall and place the

template onto the screws.

CONNECTIONS

WARNING: Before making the various

connections, check the following:

- Ensure that the treaded rods are correctly

spaced and the dimensions in drawing

adhered to, otherwise the screw

covers will not fit.

- Put the template

in place onto the

threaded rods.

CONNECTION OF SINK

1 - Remove the cap of the waste inlet loca-

ted underneath the water inlet.

2 - Connect the rubber waste connection

to the spigot with the correct clip

and crimp it with either a set of pliers or

crimpers.

3 - Connect the other end of the connector

to the 1 1/4-inch (32 mm) end

of sink waste pipe and secure it with

clip

DISCHARGE CONNECTION

1 - Slide tube

onto the discharge

connector.

2 - Fix the discharge elbow/check valve

assembly

, with clip

to the

discharge pipe.

3 - WARNING: The non-return valve must

be installed vertically with the arrow

pointing upwards.

4 - Stretch the connector and fix the end to

the non-return valve-using clip

9c CONNECTION OF THE WATER SUPPLY

Connect the water supply hose to the

compression fitting.

9d ELECTRICAL CONNECTION

Plug the cord into the receptacle.

COMPLETING THE

INSTALLATION

1 - Remount the bowl onto the treaded

rods.

2 - Sequence of washers, place first the

white PVC washer

then the steel

washer onto the treaded rods and

tighten the nuts

. Then snap the nut

covers

in place.

3 - Cut away any protruding lip of the

template around the bowl contour.

4 - Seal the bowl/wall joint with silicon.

WARRANTY

The SANISTAR

is guaranteed for 2-year,

subject to correct installation and usage.

MOUNTING THE BOWL

Once the connections have been made,

1 - Ensure that the clear tube

is still on

the treaded rods.

2 - Push the bowl onto the treaded rods;

secure the nuts (with washers) without

over-tightening them.

START-UP AND

PROGRAMMING

11a

START-UP

1 - Plug in the power socket. Wait 20

seconds: appliance initializing. Open the

water tap to rinse well. Start the normal

flush by pressing the dark grey button.

Put a few sheets of toilet paper down in

the bowl and flush again.

Note: This unit does not need to be vented.

2 - Turn on the sink tap. The unit should

sink activate automatically.

3 - Demount the bowl and check the water

tightness of all connections.

4 - WARNING: Leaking faucets will cause

the unit to activate automatically.

11b

PROGRAMMING

The length of your SANISTAR

’s flush varies

according to which cycle you choose.

Eco flush (by default, light grey button):

19 seconds and 1 gallon (3.8L): rinsing of the

bowl for 10 seconds, the pump works for 7

seconds (for 7 seconds, the bowl continues

to fill), then the bowl fills again for 2 seconds.

You can lengthen the first rinse of the eco

flush to 16 seconds if the default flush is not

enough.

Normal flush (dark grey button):

25 seconds and 1.32 gallons (5L): The bowl is

rinsed for 16 seconds, the pump works for 7

seconds (for 7 seconds, the bowl continues to

fill) then the bowl fills again for 2 seconds.

To re-program:

Note: Only the ECO option can be reprogram-

med.

• Hold the ECO button (light grey button)

down for 5 seconds.

• The motor works for 2 seconds, this means

you have entered programming mode.

• Each time you press the dark grey button

you increase the length of the ECO flush

by 1 second: each time you press it will be

validated by the motor running for a short

period.

• Each time you press the grey button you

decrease the length of the flush by 1 second:

each time you press it will be validated by

the motor running for a short period.

To exit programming mode:

• Wait for 5 seconds without pressing any

buttons.

The motor runs for 2 seconds, this means

that you have left programming mode.

Comment 1: the minimum length of the first

rinsing flush for the normal flush is 19 seconds

(default programming)

and the maximum length is 25 seconds.

Comment 2: the normal flush cannot be

modified.

CARE OF YOUR

SANISTAR

• Normal household bleaches/WC cleaners can

be used with a SANISTAR

• To avoid the build up of lime scale in the

unit, use the following procedure:

• disconnect the power supply to the unit,

• pour 1 gallon (3 to 4 liters) of water

mixed with a strong solution of descaler

into the bowl,

• leave it to stand for 1 or 2 hours, then

re-connect the electric supply,

• flush several times to clear.

The frequency of this operation will depend on the

hardness of the water in your locality. We would

recommend this be done about twice a year.

USAGE

1 - The SANISTAR

pump/macerator does

not require any special maintenance.

2 - WARNING: The SANISTAR

should

only be used for the evacuation of

normal human waste, toilet paper and

household toilet cleaners.

Damage may occur to the motor if

the following are disposed of via the

toilet: cotton wool, tampons, sanitary

napkins, wet wipes, kitchen towels,

condoms, dental floss as well as other

fabric or hard objects. Solvents, acids

and other chemicals can also cause

damage to the unit, and will invalidate

the warranty.

3 - WARNING: In case of prolonged power

failure, or going on vacation, please

close the stop valve of the the sink and

water supply.

AFTER SALES SERVICE

In the unlikely event of a failure or

malfunction, please call our after sales

service department.

WARNING: Always disconnect the electric

supply before attempting any work on the

SANISTAR