Installation Instructions

ManualsBrandsSaniflo ManualsBathSaniStar 1-piece 1.28/1 GPF Dual Flush Elongated Toilet in White with Wall Carrier

MOUNTING THE BOWL AND

CUTTING OUT THE FASCIA

PANEL

1 - When the frame is placed against a wall;

cut strips of cement board (or gypsum

board) to encapsulate the sides and front

of the frame.

2 - When the frame is inside a wall, board the

entire opening.

- Note. Make a 1-inch (25 mm) hole in the

board (corresponding with the threaded

rods). This will allow you to adjust the

depth of the rod later.

- Place the template against the wall,

positioning the holes for the WC supports

rods accordingly.

5 - Trace the inner shape of the template onto

the front.

- Remove the template and cut out the

opening as traced, being careful not to cut

any pipe or wire.

- Note. If you are tilling the wall, the tiles will

have to be cut out in the shape of the

inner opening.

8 - Finish the support wall and place the

template onto the screws.

CONNECTIONS

WARNING: Before making the various

connections, check the following:

- Ensure that the treaded rods are correctly

spaced and the dimensions in drawing

adhered to, otherwise the screw

covers will not fit.

- Put the template in place onto the

threaded rods.

CONNECTION OF HAND BASIN

1 - Saw off the tip of the waste inlet located

underneath the water inlet. De-burr it.

2 - Connect the rubber waste connection

to the spigot with the correct clip

and crimp it with either a set of pliers or

crimpers.

3 - Connect the other end of the connector

to the 1 1/4-inch (32 mm) end of

washbasin waste pipe and secure it

with clip .

DISCHARGE CONNECTION

1 - Slide tube onto the discharge

connector.

2 - Fix the non-return valve , with clip

to the discharge pipe.

3 - WARNING: The non-return valve must

be installed vertically with the arrow

pointing upwards.

4 - Stretch the connector and fix the end to

the non-return valve-using chip .

9c CONNECTION OF THE WATER SUPPLY

Connect the water supply hose to the

compression fitting.

9d ELECTRICAL CONNECTION

Plug the cord into the receptacle.

CARE OF YOUR

SANISTAR

• Normal household bleaches/WC cleaners can

be used with a SANISTAR

• To avoid the build up of lime scale in the

unit, use the following procedure:

• disconnect the power supply to the unit,

• pour 1 gallon (3 to 4 liters) of water

mixed with a strong solution of descaler

into the bowl,

• leave it to stand for 1 or 2 hours, then

re-connect the electric supply,

• flush several times to clear.

The frequency of this operation will depend on the

hardness of the water in your locality. We would

recommend this be done about twice a year .

COMPLETING THE

INSTALLATION

1 - Remount the bowl onto the treaded

rods.

2 - Sequence of washers, place first the

white PVC washer then the steel

washer onto the treaded rods and

tighten the nuts . Then snap the nut

covers in place.

3 - Cut away any protruding lip of the

template around the bowl contour.

4 - Seal the bowl/wall joint with silicon.

WARRANTY

The SANISTAR

is guaranteed for 2-year,

subject to correctinstallation and usage.

MOUNTING THE BOWL

Once the connections have been made,

1 - Ensure that the clear tube is still on

the treaded rods.

2 - Push the bowl onto the treaded rods;

secure the nuts (with washers) without

tightening them.

COMMISSIONING THE UNIT

1 - Open the stop valve to allow inflow of

water. Press the button on the back of the

bowl to start the flushing cycle. Throw a

few pieces of paper into the bowl and

flush.

2 - Turn on the washbasin tap. The unit

should activate automatically.

3 - Demount the bowl and check the water

tightness of all connections.

4 - WARNING: Leaking faucets will cause

the unit to activate automatically.

USAGE

1 - The SANISTAR

pump/macerator does not require any

special maintenance.

2 - WARNING: The SANISTAR

should

only be used for the

evacuation of normal human waste,

toilet paper and household toilet

cleaners. Damage may occur to the

motor if the following are disposed of

via the toilet: cotton wool, tampons,

sanitary napkins, wet wipes, kitchen

towels, condoms, dental floss as well

as other fabric or hard objects.

Solvents, acids and other chemicals

can also cause damage to the unit,

and will invalidate the warranty.

3 - WARNING: In case of prolonged power

failure, or going on vacation, please

close the stop valve of the hand basin.

AFTER SALES SERVICE

In the unlikely event of a failure or

malfunction, please call our after sales

service department.

WARNING: Always disconnect the electric

supply before attempting any work on the

SANISTAR

7289 N°208 USA-CDN 26/11/07 9:18 Page 5