Bidet Seat F8 User Manual Please read the user manual and check all the accessories before installation. During the warranty period, free repair service will be provided for any product issues or failures occurred under the instructions described in the User Manual. Tips Please contact with us on Saniwise’s Facebook page if you have any questions.
Contents Parts and What’s in the Box 1 Parts 1 What’s in the Box 2 Installation 3 Caution 3 Preparation 3 Installation Procedures 4 Connecting Water Inlet Hose 5 Extra Installation Tips 6 Functions 7 WASH (REAR WASH) 7 BIDET (FRONT WASH) 7 STOP 7 Cleaning and Dismantling 8 Maintenance 9 Self-diagnosis and Troubleshooting 10 Warranty Record 11 Saniwise Warranty 12 Thank you for purchasing Saniwise Bidet Seat.
Parts and What’s in the Box 1 Parts Water inlet on the left Dismantle button Water tank Seat cover Lever Seat T-shaped adapter Bidet nozzle Wash nozzle Water supply hose Bowl Shutoff valve Water inlet hose
2 What’s in the Box 1. Bidet seat and lid 2. Installation template 3. Fixing components Connecting bolts x2 Expansion nuts x2 Adapter plate x1 Sliding plates x2 4. T-shaped connector Nuts x2 5. Water inlet hose 6. User Manual User Manual Filter Note There are two methods to install the Saniwise Bidet Seat. It is recommended that you use expansion nuts. You can also use butterfly nuts. Please choose the appropriate installation method according to your specific installation needs.
Please read the following instructions carefully and install your Saniwise Bidet Seat properly. Caution 1. The water pressure limit ranges from 10 to 110 PSI. Please use as instructed. 2. The water shutoff valve should be near where the product can be installed and dismantled. 1 Preparation 1. Insert the connecting bolts into the sliding plates. Insert the connecting bolts into the holes of the sliding plates, as shown in the figure below. 2.
2 Installation Procedures Installation Method One (Recommended) 1. Dismantle the old bidet seat and lid. Loosen the hinge and remove the old bidet seat and lid. 2. Install the expansion nuts. Insert the expansion nuts into the holes of the ceramic. Be sure to firmly press down so the top of the expansion nut is flush with the ceramic toilet surface. Bidet seat and lid 3. Install the installation template. Place the installation template on the ceramic. 4. Fix the adaptable panel. Attach the adapter plate.
Connecting Water Inlet Hose 1. Turn off the water supply valve. 2. Unscrew the water supply hose from the water tank. Place a towel below the tank to catch any dripping water. Unscrew to remove 3. Using finger nut, attach the T-shaped connector to the water tank where you removed the water supply hose. 4. Attach the water supply hose to the bottom of the T-shaped connector. Finger nut 5.
7. Wipe the hoses and connectors thoroughly with a towel and carefully observe for any leaks for at least 10 minutes. Tighten any connectors gently until leakage stops. If any leaks continue, turn off the water supply and check older hoses for damaged rubber O-rings and replace them if necessary. *Optional, only do the following if water pressure is too low. Please remove the regulator cover and regulator O-ring under the following conditions: a. When the water pressure is lower than 10 PSI. b.
4. In most cases everyone is happy with the pressure that the cleaning jets put out. If for any reason you would like a stronger stream, please refer to page 6 in the instructions and it will explain how to remove the pressure regulator and dramatically increase the pressure. If you still need help, feel free to send us an email at support@saniwise.com. Functions WASH (REAR WASH) 1) Turn the lever clockwise from the vertical position.
5 Cleaning and Dismantling 1. Clean the exterior of the bidet seat. Use a smooth sponge/cloth with diluted dish detergent to clean the product. Do not use the following types: hydrogen chloride detergent, paint thinner, benzene, abrasive paper, polishing agent, bleach, or chlorine. 2. Clean the spray nozzles. Pull out the nozzle softly and use smooth cloth/sponge or toothbrush with liquid dish soap to clean the nozzle. Paining thinner Insecticide Abrasive paper 3. Clean the filter and regulator.
6 Maintenance 1. Lever Replacement 2. Nozzle Replacement 1) Remove the old lever as shown in figure A. 2) Insert the new lever rib into the corresponding slot. When the new lever is mounted properly, a click will be heard. 1) Pull out the tube and hold it, then remove the old nozzle, as shown in figure A. 2) Mount the new nozzle to the corresponding slot on the tube. Now, the nozzle is replaced successfully. B A C A Nozzle 3. Regulator Replacement 1) Rotate the lever forward.
7 Self-diagnosis and Specifications Self-diagnosis and Troubleshooting Issue The water pressure is low when using WASH/BIDET. Cause Solution The bidet seat’s water pressure is low. Turn the lever forward or backward to the highest setting during use. The pressure of the water supply is low. If the pressure of the water supply is too low, please contact your local water department. The shutoff valve is turned off. Turn on the shutoff valve. The T-shaped connector’s filter is stuck.
Warranty Record Dear customer, Thank you for choosing Saniwise. If any failure or issue occurs, please check your Saniwise Bidet Seat following the troubleshooting methods in this manual first. If the failure or issue cannot be fixed, please follow the return instructions on the next page. A. Related Information Name: Tel: Address: Model No.: Date of Purchase: Warranty Period: B. Notes 1. Please make sure the above information is completed before requesting the warranty service. 2.
Saniwise Warranty Your Saniwise Bidet Seat is warranted against defects in materials or workmanship for one (1) year from the date of original purchase. A defective product or defective parts returned to Saniwise will be repaired or exchanged for a Refurbished Saniwise Bidet Seat as determined by Saniwise in their sole discretion. Saniwise will not charge for labor or parts in connection with warranty repairs or replacements.