User Guide

ManualsBrandsSanus Systems ManualsOtherAFV48B

Assembly Instructions for Model: AFV48

Sanus 6436 City West Parkway, Eden Prairie, MN 55344 03.09.12 (6901-100073 <01>)

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Thank you for choosing the Sanus AFV48. If you do not

understand these directions, or have any doubts about

the safety of the installation, please contact Sanus at

800.359.5520 or www.sanus.com. Check carefully to make

sure that there are no missing or defective parts. Our

customer service representatives can quickly assist you

with installation questions and missing or damaged parts.

Replacement parts for products purchased through authorized

dealers will be shipped directly to you. Never use defective

parts. Improper installation may cause damage or serious

injury. Do not use this product for any purpose that is not

explicitly speciﬁ ed by Sanus. Sanus can not be liable for

damage or injury caused by incorrect assembly, or incorrect

use. Please contact Sanus before returning products to the

point of purchase.

Supplied Parts and Hardware

1/4-20

Shelf Connector - A

Qty. 10

Grommet - D

Qty. 4

Spacer - C

Qty. 2

Top Bolt - B

Qty. 6

9” Pillar - G

Qty. 6

7” Pillar - F

Qty. 4

3” Pillar - E

Qty. 6

Bottom & Middle Shelf - I

Qty. 2

Top Shelf - H

Qty. 1

Allen Key - L

Qty. 1

Foot - K

Qty. 6

Front Brace - J

Qty. 1

200 lbs

90.9 kg

200 lbs

90.9 kg

200 lbs

90.9 kg

DO NOT EXCEED

WEIGHT LIMITS!

Summary of content (4 pages)

PAGE 1
Assembly Instructions for Model: AFV48 Thank you for choosing the Sanus AFV48. If you do not understand these directions, or have any doubts about the safety of the installation, please contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts.
PAGE 2
Step 1: Foot Assembly Diagram 1 A Thread a Foot (K) into each 3” Pillar (E). Thread a Shelf Connector (A) into the other end of the 3” Pillar (E) until tight. E Repeat this process for each remaining 3” Pillar. K Step 2: Add Bottom Shelf Insert each Foot Assembly from Step 1 through the Bottom Shelf (I) as shown in Diagram 2. Diagram 2 I Foot Assembly Step 3: Add 9” Pillars Thread a 9” Pillar (G) onto each exposed Shelf Connector (A) until tight.
PAGE 3
Step 4: Add Middle Shelf Place the Middle Shelf (I) on the 9” Pillars (G). A Shelf Connector (A) should be protruding above the Middle Shelf at each corner. Place two Top Bolts (B) through the Middle Shelf (I) and thread them into both middle 9” Pillars (G) as shown in Diagram 4. Using the Allen Key (L), tighten both Top Bolts (B). Diagram 4 B I A G Step 5: Add 7” Pillars Thread and hand tighten a 7” Pillar (F) onto each exposed Shelf connector (A).
PAGE 4
Step 6: Add Top Shelf Place the Front Brace (J) on the two front 7” Pillars (F) as shown in Diagram 6 and Detail A. Place the Top Shelf (H) (with its curved edge towards the front) on the Front Brace (J), and 7” Pillars (F) as shown in Diagram 6. Insert two Top Bolts (B) through the holes in the Top Shelf (H), Front Brace (J) and two front 7” Pillars (F) as shown in Diagram 6 and Detail A. Place a Spacer (C) on both rear 7” Pillars (F) as shown in Diagram 6 and Detail B.