User's Manual

ManualsBrandsSanus Systems ManualsPatio FurnitureSanus Systems CFAR47

Assembly Instructions for Model: CFAR47

Thank you for choosing the Component Furniture line from Sanus Systems! Use

this manual to congure the CFAR47 as shown on the right. The CFAR47 is de-

signed to hold a LCD, Plasma or DLP TV.

Safety Warning: If you do not understand these directions, or have any doubts

about the safety of the installation, please call a qualied contractor or contact Sa-

nus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there

are no missing or defective parts. Our customer service representatives can quickly

assist you with installation questions and missing or damaged parts. Replacement

parts for products purchased through authorized dealers will be shipped directly to

you. Never use defective parts. Improper installation may cause damage or serious

injury. Do not use this product for any purpose that is not explicitly specied by

Sanus Systems. Sanus Systems can not be liable for damage or injury caused by

incorrect assembly, or incorrect use. Please call Sanus Systems before returning

products to the point of purchase.

Required Tools: Drill, 3/16” drill bit, phillips screw driver, at head screw driv-

er, crescent wrench, tape measure.

Supplied Parts and Hardware: Hardware shown at actual size. Some

parts may come pre-assembled**

Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113 10.10.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

(4) Carpet Spike - a (12) Cam Pin - b (8) Spacer - c (8) Back Panel Bolt - d

(2) Phillips Pan Head Bolt - e (4) Dowel - f (4) Glass Shelf Pin - g (8) Wood Shelf Pin - h

(4) Wood Screw - i (4) Knob Bolt - j

(8) Hinge Plate Screw - k

(16) Hinge Screw - l

(2) Tip Protector Bolt - m (2) Stop Nut - n (8) Hinge Car Bolt - o

(2) Lag Bolt - p (2) Lag Bolt Washer - q (1) Allen Key - r

Summary of content (13 pages)

PAGE 1
Assembly Instructions for Model: CFAR47 Thank you for choosing the Component Furniture line from Sanus Systems! Use this manual to configure the CFAR47 as shown on the right. The CFAR47 is designed to hold a LCD, Plasma or DLP TV. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts.
PAGE 2
Parts: Not all parts shown at the same scale (4) Foot - s (4) Door Knob - t** (4) Hinge Plate - x** (4) Bi-fold Hinge - y (1) Shelf Retainer - u (4) Hinge Car - z (3) Front Rail - cc (1) Shelf Bracket - v (4) Small Door Hinge - w (2) Furniture Bracket - aa (2) Wall Bracket - bb (3) Back Rail - dd (2) Bi-fold Door - gg (2) Side Panel - ee (2) Back Panel - ff (1) Top - ii (1) Glass
PAGE 3
Step 1: Add Wood Shelf Pins and Feet to Side Panels Insert a Wood Shelf Pin (h) into the holes adjacent to the two lower sets of cams in each Side Panel (ee). See Detailed View A of Diagram 1 for assistance. Add a Foot (s) to each pillar of the Side Panel (ee). If you wish to install the Carpet Spikes (a), thread each Carpet Spike into the Foot. You can adjust the height of the Carpet Spikes with the Nut. See Detailed View B of Diagram 1 for assistance.
PAGE 4
Step 2: Add Front and Back Rails Add Front Rails - Attach the Front Rail (cc) to the Side Panel Assembly (ee) by sliding the clamp down the groove in each Side Panel pillar as shown in the Top View of Diagram 2. Make sure the smooth side of the Front Rail is facing outward and the open channel faces down as seen in the Detailed View below on the right.
PAGE 5
Step 3: Prepare TV Shelf Insert two Wood Screws (i) through the Shelf Bracket (v) and into the underside of the Wood Shelf (kk). Tighten each Wood Screw with a phillips screw driver. See Diagram 3 for assistance. Diagram 3 i kk v Step 4: Add Wood Shelves Press fit the Wood Shelves (kk) so they lock into the Wood Shelf Pins (h).
PAGE 6
Step 5: Secure upper Wood Shelf Secure the Shelf Retainer (u) to the upper Wood Shelf (kk) by inserting a Wood Screw (i) through the Shelf Retainer and thread it into the Wood Shelf. Secure the Shelf Bracket (v) to the upper Back Rail (dd) by threading a Phillips Pan Head Bolt (e) through the Shelf Bracket and into the Back Rail (dd). See Diagram 5 for assistance.
PAGE 7
Step 7: Add Front and Back Rail Add Front Rail - Attach the Front Rail (cc) to the Side Panel (ee) by sliding the clamp down the groove in each Side Panel pillar as shown in the Top View of Diagram 7. Make sure the smooth side of the Front Rail is facing outward and the open channel faces down. Once the Top of the Front Rail is level with the Side Panel, tighten the allen bolt on the back side of the Front Rail so the clamp widens to hold the Front Rail firmly in place.
PAGE 8
Step 8: Add Back Panels Add Back Panels (ff) to the assembly by inserting a Back Panel Bolt (d) through each hole in the Back Panels, a Spacer (c) and thread it into the inserts in the Back Rail (dd). Before tightening the Back Panel Bolts, insert the Furniture Bracket (aa) under the Back Rail. Once the Back Panels are secured, the Furniture Brackets will be held in place. See Diagram 8 for assistance.
PAGE 9
Step 9: Add Top Insert a Dowel (f) into each hole in the bottom side of the Top (ii). Add Top so each Dowel is secured in the corner pillar in the Side Assembly (ee). See Diagram 9 for assistance. Diagram 9 Detailed View ii f Step 10: Add Glass Shelf Add Glass Shelf Pins (g) to the desired locations into the Side Panel (ee) in the lower portion of the armoire. Insert the Glass Shelf (jj) into the assembly so it rests on the Glass Shelf Pins.
PAGE 10
Step 11: Add Hinges and Knobs Add Hinges (w,y) to the Doors (gg,hh) by inserting a Hinge Screw (l) through the Hinge and into the Door. Tighten each with a phillips screw driver. Attach the Door Knobs (t) by inserting a Knob Bolt (j) through the Door (gg,hh) and into the Door Knob. Tighten each with a phillips screw driver. Repeat process until all Hinges and Door Knobs are secured. See the Detailed Views of Diagram 11 below for assistance.
PAGE 11
Step 12: Add Hinge Plates and Small Doors Add the Hinge Plates (x) by inserting a Hinge Plate Screw (k) through the Hinge Plate, and into the holes in the Side Panel (ee). Tighten each with a phillips screw driver. Repeat the process for all four Hinge Plates. See Diagram 12 for assistance. To attach each Hinge (w) to its Hinge Plate (x), the bolt along the back center of the Hinge Plate must be loose during installation. The slot on the end of the Hinge will fit around the bolt on the Hinge Plate.
PAGE 12
Step 14: Secure Wall Bracket to wall Locate two wood studs using a stud finder. It is a good idea to verify where the stud is with a awl or a thin nail. Mark the location of each stud. To find the height, measure 54 inches up from the floor. Mark the location on the stud. Drill a 2.5” deep hole with a 3/16” drill bit at each marked location. Insert a Lag Bolt (p) through a Lag Bolt Washer (q), a Wall Bracket and drive it into the pre-drilled hole until secured into the stud.
PAGE 13
Step 16: Hinge Adjustment for small Door Each hinge Assembly is adjustable in multiple directions. See Diagram 16 for assistance. Diagram 16 Side Adjustment Depth Adjustment Height Adjustment Step 17: Hinge Adjustment for Bi-fold Door To adjust the Bi-fold Hinges (y), loosen the screws labeled in the Diagrams below for the specified movement. Note: For height adjustment, loosen the Hinge Car Bolts (o) and slide the Hinge Cars (z) in the track until desired adjustment is complete.