CFR2115, CFR2127, CFR2136, CFR2144 Instruction Manual We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We’re ready to help! Scan for more information san.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE MANUAL PRIOR TO USE Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment. The total weight capacity for the CFR2100 series: CFR2115 226.8 kg (500 lb) CFR2127 340.2 kg (750 lb) CFR2136 385.5 kg (850 lb) CFR2144 453.6 kg (1,000 lb) Each 2U shelf supports up to 22.6 kg (50 lb), and each 1U shelf supports up to 13.6 kg (30 lb). Each optional 3U shelf supports up to 36.
Parts and Hardware 03 CFR2115 CFR2127 CFR2136 CFR2144 8 12 16 18 04 CFR2115 CFR2127 CFR2136 CFR2144 01 x1 02 x2 4 6 8 9 M5 x 10 mm 10-32 x 3/4 in.
Load Your Components CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage: To prevent instability: • Always load the rack from the bottom up and load the heaviest item first. • 50% of the total weight should be mounted in the lower 1/3 of the rack.
Load Your Components OPT CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage: To prevent instability: • Always load the rack from the bottom up and load the heaviest item first. • 50% of the total weight should be mounted in the lower 1/3 of the rack. • Follow these additional requirements when loading rack on its back and then lifting rack to an upright position: 1 1. Leveling feet, if installed, need to be adjusted all the way in. 2.
Using Backstops and Component Straps Rack Shelf Backstops NOTE: rear view with back panels removed. 1. Insert backstop 03 into slot behind component. 2. Slide backstop 03 forward until firmly against component and twist 90 degrees. Component Straps NOTE: side view with panels removed. A. Slide straps 04 through slots in sides of shelves. B. Wrap straps 04 over component to secure.
Access Panels for Cable Management OPT 7
Install Fan for Additional Ventilation (Top or Bottom) CAUTION: Avoid damage to your components due to overheating. Make sure that there is adequate space between each unit for proper airflow. Operating temperature inside the rack must not exceed 104°F (40°C). To install fan: Remove the vented panel. CAUTION: Cut edges may be sharp. Remove any metal burrs that remain in the panel frame. Mount the cooling fan using the screws 05 included.
Adjust Shelves and Blanking Panels NOTE: Align the bottom of the shelf or blanking panel B with the lines L on the rack rail.
Adjust Rack Rails Remove the shelves and blanking panels before adjusting the rails. Adjust the right and left rails evenly. NOTE: For clarity, the front door, top, and side panels are not shown.
Switch Back Panels OPT 1 1. Remove large upper panel. 2. Remove small lower panel and frame. 3. Fit bottom of large panel into rack frame and angle the panel up until sliding locks snap in place. 4. Flip small panel 180 degrees. 5. Screw panel frame into rack frame and replace small panel.
Reverse the Front Door Remove the door OPT 1. Turn upper door pin to release from locking tab and pull down to release door from rack and lift door from rack frame. 2. Release upper pin and turn it back to secure it with the locking tab. 3. Remove spacer from bottom door pin. 1 NOTE: Spacer must be used with pin on bottom of door.
Reverse the Front Door - continued Flip the door OPT 6 4. Fit spacer onto bottom pin and fit bottom pin into bottom mounting hole in rack. 5. Turn upper pin to release from locking tab and pull down. Fit pin into upper mounting hole in rack. 6. Release pin and turn pin to secure it with locking tab.
Reverse the Front Door - continued Flip the door 7 Remove screws and bracket. 8 9 Reattach screws and bracket. 10 Loosen the locking cam screw. 12 Tighten the locking cam screw. 11 14 OPT Flip the locking cam tab to the side nearest the edge of the door. Flip the door handle.
Add Keyed Lock to Door (Sold Separately) OPT Install keyed lock (purchased separately) in plug hole. Remove plug from side panel.
Ganging Racks (Ganging Kit Sold Separately) OPT 1 2 Remove side panels on sides to be connected. Move racks together until sides are touching. 3 IMPORTANT Make sure both racks are level with each other. Fit four ganging clips (GC) into frame slots. Press down on clips to secure. IMPORTANT Make sure all four ganging clips are fully engaged.
Level Feet OPT Adjust the feet to level the rack. Tighten nuts until they are flush with the bottom of the rack. CAUTION: To avoid potential injury or property damage, always ensure that your rack is level.
Thank you for choosing Sanus! Please take a moment to let us know how we did: Call us: 1-800-359-5520 UK: 0800 056 2853 Email us: info@sanus.com Leave a review: sanus.com Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations.
NEW SANUS FOUNDATIONS® COMPONENT SERIES AV RACKS Introducing the SANUS 100 Series Racks – the Second Generation The engineers at SANUS took the Component Series racks to the next level with the SANUS 100 Series Racks – the Second Generation. Constructed of heavy-gage welded steel, the 100 Series come pre-assembled with vented shelves and blanking panels to simplify ordering and installation.
® NEW SANUS FOUNDATIONS COMPONENT SERIES AV RACKS MODEL: CFR2115 MODEL: CFR2127 DESCRIPTION 15U AV Rack DESCRIPTION 27U AV Rack DIMENSIONS (W X D X H) 23.6" x 23.6" x 34" / 60 x 60 x 86.4 cm DIMENSIONS (W X D X H) 23.6" x 23.6" x 55" / 60 x 60 x 139.7 cm RACK SPACES 15U RACK SPACES 27U WEIGHT CAPACITY 500 lbs / 226.8 kg WEIGHT CAPACITY 750 lbs / 340.2 kg PACKAGE DIMENSIONS (W X D X H) 26.4" x 26.4" x 33.46" / 67 x 67 x 85 cm PACKAGE DIMENSIONS (W X D X H) 26.4" x 26.4" x 53.
&21),*85$7,21 8 23(1 8 6+(/) 8 6+(/) 8 23(1 8 %/$1. 3$1(/ 8 6+(/) 8 %/$1. 3$1(/ 8 6+(/) 8 %/$1.