LMF115 INSTRUCTION MANUAL Para Español ver página 18 WE’RE HERE TO HELP Want to watch a video that shows how easy this DIY project will be? Watch it now at: SANUS.com/2848 Recommended placement Check it out at: SANUS.com/2850 Get it right the first time. HeightFinder™ shows you where to drill. Our US-based install experts are standing by to help.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE Before getting started, let’s make sure this mount is perfect for you! (including accessories) weigh more than 50 lb (22.6 kg)? What is your wall made of? No — Perfect! 50 lb (22.6 kg) Yes — This mount is NOT compatible. Visit MountFinder.sanus.com or call 1-855-734-7805 to find a compatible mount.
Dimensions TV INTERFACE 3.94in 100mm MIN 3-D 15.75in 400mm MAX 15.75in 400mm MAX 7.87in 200mm 11.81in 300mm 3.94in 100mm MIN WALL PLATE TOP VIEW - EXTENDED 4.01in 101.9mm 45deg 8.27in 210mm SIDE VIEW - EXTENDED 15deg DOWN 5deg UP 45deg 9.92in 251.9mm SIMULATED 46" FLAT SCREEN TV 0.33in 8.4mm 15.02in 381.4mm FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED SIDE VIEW RETRACTED 17.07in 433.7mm 17.07in 433.7mm 6deg ROLL 3.07in 78mm 2.78in 70.
Supplied Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. STEP 1 Parts and Hardware 01 TV Screws (qty. 4 each) [Only one size fits your TV] Washers (qty.
STEP 2 Parts and Hardware STEP 2B: Concrete Installation Kit CMK1 [NOT INCLUDED] Contact Customer Service to inquire about the CMK1 Concrete Installation Kit. Concrete Anchor C1 (qty. 2) Fischer UX10 x 60R Anchor Lag Bolt Wall Plate Template 07 09 Arm Assembly 08 (qty. 1) (qty. 2) (qty. 1) 5/16 x 2 ¾ in. STEP 3 Parts and Hardware Nut Cap 10 (qty. 1) Locking Screw Washer 11 (qty. 1) 12 M5 x 6mm (qty.
STEP 1 Attach TV bracket to TV 1.1 Measure Your TV Hole Pattern 1.2 Assemble Your TV bracket Measure the width and height of your TV hole pattern in cm. Based on your TV hole pattern measurements (W cm x H cm), determine your TV bracket configuration: A, B, C, D or E. Record your measurements: A Width_______cm x_ Height_______cm inches cm mm 3 4 7⅞ 11 ¾ 15 ¾ 7.5 10 20 30 40 75 100 200 300 400 B For TV Hole Pattern Measurements (Dimensions in cm) 30.0 x 30.0 40.0 x 40.
C D For TV Hole Pattern Measurements (Dimensions in cm) 40.0 x 30.0 E For TV Hole Pattern Measurements For TV Hole Pattern Measurements 40.0 x 20.0 20.0 x 40.0 (Dimensions in cm) 40.0 [15.75] (Dimensions in cm) 20.0 [7.87] 40.0 [15.75] 30.0 [11.81] 05 05 20.0 [7.87] 40.0 [15.75] 05 05 05 04 04 04 05 06 Assemble extenders 05 onto TV bracket 04 and secure using eight screws 06 in the corner holes indicated.
1.3 Select TV Screw Diameter 1.4 Select TV Screw Length a: For flat-back TVs, b: Spacers 03 supplied for: Only one size fits your TV. no spacers 03 required. M4 M6 ●● Round (irregular) back TVs ●● Extra space needed (for cables or inset mounting holes) M8 If your TV included inset spacers or wall mount adapters, use them UNDER the mount hardware. CAUTION: a b FLAT BACK ROUND BACK Verify adequate thread engagement with your screw/ washer/spacer combination AND TV bracket.
1.5 Attach TV Bracket Position your TV bracket configuration (A, B, C, D or E) onto your TV, making sure the bracket is both centered and level over your TV hole pattern. NOTE: The hanging tab H on TV bracket 04 must be oriented toward the top of the TV. Secure the TV bracket using your selection: (a) screw/washer or (b) screw/washer/spacer. CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step.
STEP 2A Attach Wall Plate to Wall Wood Stud Installation CAUTION: Avoid potential personal injury or property damage! ●● Drywall covering the wall must not exceed 5/8 in. (16 mm) ●● Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm) 1. Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder. 2.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. Remove template 07 . IMPORTANT: Be sure to drill into the center of the stud. IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). 4. Install arm assembly 08 using two lag bolts 09 . Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts 3 4 07 09 . 09 08 3 in. (75 mm) 7/32 in. (5.
STEP 2B Attach Wall Plate to Wall Solid Concrete / Concrete Block Installation CAUTION: Avoid potential personal injury or property damage! ●● Mount arm assembly 08 directly onto concrete surface (no wall covering) ●● Minimum solid concrete thickness: 8 in. (203 mm) ●● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) 1. Position the template 2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
3. Remove the template 07 and insert two anchors C1 (Fischer UX 10 x 60R - included in the Concrete Installation Kit CMK1*). CAUTION: Be sure the anchors 4. Install arm assembly 08 C1 are seated flush with the concrete surface. using two lag bolts 09 . Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts 09 .
STEP 3 Hang TV onto Wall Plate HEAVY! You may need assistance with this step. 1. Install the nut cap 2. Fold first section of the arm of arm assembly 10 on arm assembly 08 1 . 08 against the wall to provide stability.
3. Hang the TV onto the arm of arm assembly 4. Lock the TV to the arm assembly 08 IMPORTANT: This locking screw 08 by first hooking the hanging tab H , then resting the TV into place. with locking screw 12 11 and washer 12 . must be installed to secure the TV onto the arm assembly 3 04 H 08 .
Manage Cables Cables can be routed through the cable channel on the top and bottom of the arm assembly 08 16 08 for a cleaner look.
TV Adjustments TILT ADJUSTMENT LEVEL ADJUSTMENT REMOVING THE TV Your TV should adjust easily when moved, then stay in place. If your TV is too loose or too tight, adjust the tilt tension knob by hand. To adjust the leveling of your TV, loosen the locking screw 11 , level your TV, then tighten locking screw 11 . IMPORTANT: This locking screw 11 must be installed to secure the TV onto the arm assembly 08 . NOTE: Once your TV is in place, tighten the tilt tension knob to prevent unwanted movement.
ESPAÑOL INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO. Antes de comenzar, verifiquemos que este soporte sea el ideal para sus necesidades. los accesorios? 2 ¿De qué está hecha su pared? 22,6 kg (50 lbs.) No — ¡Perfecto! Sí — Este soporte NO es compatible. Visite Mountfinder.Sanus.com o llame al 1-855-734-7805 para encontrar un soporte compatible.
ESPAÑOL Dimensiones Ver página 3 Piezas y accesorios suministrados Ver página 4 ADVERTENCIA: Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia. Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor; póngase en contacto con el servicio de atención al cliente. Nunca utilice piezas deterioradas.
ESPAÑOL 1,3 Seleccione el diámetro de los tornillos para el televisor Enrosque manualmente los tornillos en los encastres roscados del dorso del televisor a fin de determinar qué diámetro de tornillos (M4, M6 o M8) utilizar. 1,4 S eleccione el largo de los tornillos para el televisor a: Si el dorso del televisor es plano, no se requieren espaciadores 03 b: Los espaciadores 03 y los tornillos largos se proporcionan para: .
ESPAÑOL 3. Con una mecha de 5.5 mm (7/32'') de diámetro, realice los orificios guía. Retire la plantilla de placa mural 07 . IMPORTANTE: Asegúrese de perforar el centro del montante. IMPORTANTE: Los orificios guía deben realizarse hasta una profundidad de 75 mm (3''). 4. Instale el módulo de la placa mural 08 usando dos tornillos tirafondo 09 . Ajuste los tornillos tirafondo solamente hasta que queden firmes contra la placa mural.
ESPAÑOL PASO 3 Colgar el televisor en la placa mural Ver página 14 ¡ELEMENTO PESADO! Es posible que necesite ayuda en este paso. 1. 2. 3. Instale la la tapa 10 en del módulo de la placa mural 08 . Pliegue la primera sección del brazo del módulo de la placa mural 08 contra la pared para dar mayor estabilidad. Para colgar el televisor en el brazo del módulo de la placa mural 08 , primero enganche la lengüeta colgante H y luego apoye el televisor en su lugar. 4.
ESPAÑOL Ajustes del televisor Ver página 17 AJUSTE DE LA INCLINACIÓN AJUSTE DEL NIVEL El televisor debe acomodarse fácilmente al moverlo, y luego quedar en su lugar. Para ajustar la nivelación de su televisor, afloje el tornillo de seguridad 11 , nivele el televisor, y luego ajuste el tornillo de seguridad 11 . Si el televisor está demasiado suelto o demasiado ajustado, ajuste la perilla de tensión de inclinación manualmente.
Watch the installation video or call our Customer Care team for help SAN.US/2848 1-855-734-7805 Legrand AV Inc. and its affiliated corporations and subsidiaries (collectively, “Legrand”), intend to make this manual accurate and complete. However, Legrand makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product.
