:1131..1'111.1 1:1 VISIONMOUNT LT25 6901-100191 <00> Thank you for choosing the Sanus Systems LT25 wall mount.The LT25 is designed to hold monitors weighing up to 79 kg (175 Ibs).The LT25 is also adjustable, allowing + 80 and - 10° of tilt. ,---------------- A C A U T I O N - - - - - - - - - - - - - - - - - , Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may cause property damage or personal injury.
Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Systems Customer Service. Never use damaged parts! / A WARNING - - - - - - - - - - - - - - - , This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! o o Hardware and procedures for multiple mounting configurations are included.
[01] x 1 [OS] x4 [03] x 1 [02] xl ~ ~ [08] x4 [09] x4 [07] x4 [06]x4 [10] x4 [04] x 4 [11] x4 M4x30mm [12] x 6 @ o M4/MS [13] x4 [15] x 6 [14] x4 M6/M8 [16] x 8 [17] x4 @ M4 MS [18] x4 [19] x4 [23] xl 6901-100191 <00> M6 [20] x 4 M8 [21] x4 [22] x 6
I (((-~i r 1 ! ~ .~ ~ 1 Wood Stud Mounting /16In. A A: Locate stud with studfinder and awr B: Mark the location of the mounting holes Drill the holes to a depth of 2.5 in. 0: Mount the plate to the wall c: B ,I ~ . .'I'i " 1~ ':,',T· I :1 1 ' 1 I, ~ ------ ...------ A CAUTION-----..., Do not overtighten the lag bolts! TIghten the lag bolts [12J only until the washers [1 SJ are pulled against the wall plate [01 J.
1.1 Concrete Mounting A A: Mark the location of the mounting holes B: Drill the holes to a depth of 2.5 in. C: Mount the plate to the wall .....------ A. CAUTION - - - - - - - - , Avoid potential personal injuries or property damage! Never drill into the mortar between the blocks. Be sure the anchors [22] seat flush with the blocks. B >64mm (2.5 in.) r.-.' I I I I _-0 ---- -:::.--~-+--::~ ~ ----- .....------ A.
2 Determine width between mounting holes A: For monitors with holes less than 400mm wide, proceed to step 4. B: For monitors with holes greater than 400mm wide, proceed to step 3. _ _ _ _~ _ _ _ _~ Proceed to step 4. Prodeed to step 3.
For monitors with hole spacing greater than 400mm. 3 Remove knobs from brackets /02] Re-install knobs on opposite sides of brackets /03] -~ \9 ~ ------fp~ i 6901-100191 <00> ~4---
4 For Monitors with Flat Backs e [18,19, 20,21] [04,05, 06,07] Install brackets to monitor using the appropriate hardware For Monitors with Curved or Obstructed Backs Install brackets to monitor using the appropriate hardware e 6901-100191 <00>
5 Hang TV on Wall A WARNING To avoid personal injury or property damage, bracket knobs must be tight when TV is in wiring positon.
6 Wire TV mOnlto~;es as necessary o With arrange ca On wiring position, , , , , 6901-100191 <00>
6.1 ,..---- A CAUTION-----.,.;...... Be sure the latches hook onto the back of the wall plate as shown below. ~-~-~ --~---~----- -~-~-~-------------~ - - - - - - - - -~-------~- ----- -~ ------~-----~---~----- ------~----~~-------- ----~--~--- ---::::-::_--------- -- -:::.
7 Height/Level adjust Use the Allen Key [23] to adjust monitor height NOTE Complete wiring before performing this step. "r::::::::::::::::---:,i ---- ---- --- :::~~~~~::~~~~------- , ,, ,, ,, ,, ,, , ,, ,, ,, , , ,, ,, ,, ,, ,, ,, ,, , ---- ----------- ----------------------------- ------- ... _---- ... _-- ±2.5° .- ~l------ .
e For Latch Release -- ~~----- ------ A WARNING To avoid personal injury or property damage, bracket knobs must be tight when TV is in wiring positon. Pull Wiring Latches forward to move monitor to wiring position ----- -------- ,, ,,, ,,, ,, ,,, , '----- ----------------- r....... j--="""""""""""""""""""-- ! !i I : > .•....< •••••••••<. ----- 6901-100191 <00> --"""~"~"""""""""""""""~""',.---_ f , ,, ,, , ,, ,,, , ,, ,,, , , ,, , , ,, ,, ,, IL ------ ------- . -- -___ I : \ \ ,
(SAV, Inc. and its affiliated corporations and subsidiaries (collectivefy,·CSAV'1, intend to make this manual accurate and complete. However, (SAV makes no claim that the information contained herein covers all details. conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product.The information contained in this document is subject to change without notice or obligation of any kind.
