EXZES ZZ Radio System Manual

106
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
Receiver won't power ON
Audible alarm beeps continuously
One or more LEDs flashing
No key-press, Trim, alarm or alert sounds
Servo movement is slow
Servo does not move when using Trim Switch
Inadequate transmitting range
Servo(s) move the wrong direction
Servo Horn(s) not centered
Control linkage(s) bind
Servo moves too much or not enough when
Trim Switch is pressed
Throttle servo moves to programmed position
without input
Can't program Receiver Battery Voltage Fail Safe
LCD is difficult to read
Throttle servo pulsates
Model veers right or left without control input
Model accelerates without control input
Model does not react to Throttle
No Telemetry connection
Can't change Racing Modes
Can't program RACING menu functions
separately for each Racing Mode
Model seems extremely sensitive to control input
There is no LCD Backlight
LCD Backlight keeps turning OFF
Receiver batteries are dead
Receiver batteries not installed correctly
Incorrect polarity or loose connection
Low transmitter battery voltage
Transmitter left ON 10 minutes or more
without control input
Transmitter battery voltage too high
Indicates transmitter status
Audible tones are Muted
Low receiver battery voltage
Control linkages binding
UsinganegativeServoSpeedvalue
Trim is outside of operational range
Low transmitter battery voltage
Low receiver battery voltage
Receiver antenna not mounted correctly
Incorrect Servo Reversing setting
Servo horn not installed correctly
Servo Sub-Trim out of adjustment
To much servo travel
Trim Step resolution requires adjustment
Receiver battery voltage has reached
programmed Receiver Battery Voltage
Fail Safe voltage value
Throttle channel Fail Safe value set to
FREE or HOLD
Transmitter left in direct sunlight too long
Contrast setting too high or too low
ABS function is turned ON
Steering out of trim
Throttle out of trim
Throttle Offset function turned ON
Throttle Hold function turned ON
Throttle Hold function turned ON
Telemetry system turned OFF
Usingnon-Telemetrycapablereceiver
Out of Telemetry receiving range
Racing Mode Inhibited (turned OFF)
SEPARATE value for functions in R-MODE
menu set to OFF
Not choosing desired Racing Mode first
Dual Rate value(s) set too high
Feeling value set too high
LCD Backlight is turned OFF
LCDMODEissettoKey-On
Replace or recharge receiver batteries
Reinstall receiver batteries, observing correct polarity
Double-check polarity and all connections
Replace or recharge transmitter batteries
Move Steering Control Stick or Throttle Control Stick,
or press any key to clear alarm and continue operation
Usetransmitterbatterywhosevoltageis9.6voltsor
less when fully charged
For more information, see the LED Condition Indicators
table on page 10.
IncreaseTonevolumeinBUZZERmenu
Replace or recharge receiver batteries
Adjust control linkages to operate smoothly
Increase Servo Speed value
Center Trim Switches to '0', center the servo horn and
control linkages
Replace or recharge transmitter battery
Replace or recharge receiver batteries
Mount receiver antenna as recommended
Change Servo Reversing setting
Turn servo horn 134º and reinstall
Adjust Servo Sub-Trim to center servo horn
Decrease servo travel using EPA function
Adjust Trim Step resolution
Replace or recharge the receiver batteries
Set Throttle channel Fail Safe to a percentage value
Place transmitter in shade
Readjust contrast setting
This is normal under Braking with ABS function ON
UseSteeringTrimSwitchtoadjustSteeringTrimso
model drives straight
UseThrottleTrimSwitchtoadjustThrottleNeutralPoint
Turn Throttle Offset function OFF
Turn Throttle Hold function OFF
Turn Throttle Hold function OFF
Turn Telemetry system ON
UseFH4TTelemetry-capablereceiverorSuperVortex
series ESC
Shorten distance between transmitter and receiver
Activate (turn ON) Racing Mode
Change SEPARATE value in R-MODE menu ON for
desired functions
Choose desired Racing Mode to program function for,
then program function
Decrease Dual Rate value(s)
Decrease Feeling value
SetLCDMODEtoKey-OnorAlways
This is normal to save battery power. Increase TIME
value or set LCD MODE to Always
PROBLEM
CAUSE SOLUTION