EXZES ZZ Radio System Manual

34
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
ASSIGN MENU
{
SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS
}
SYSTEM
Changing the Trim Switch Function Assignments, Continued:
4) Scroll UP or DOWN to highlight the Trim Switch Number you would like to
change. Choose from TRM1, TRM2, TRM3, TRM4 or TRM5.
5) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredfunction
for the Trim Switch Number you highlighted.
Changing the Trim Switch Step Value:
TheStepfunctionallowsyoutoadjusthowfaraservotravelsorafunctionmoveswhenaTrimSwitchispressed.Youcan
Increase the Trim Resolution by Decreasing the Step value, so that the amount of travel is less when you press the Trim Switches.
This makes it possible to fine-tune travel extremely accurately.
Alternately, you could Decrease the Trim Resolution by Increasing the Step value, so that the amount of travel is more when you
press the Trim Switches. This may not be as accurate, but it allows you to command large amounts of travel or function
movement at a time.
1) FromwithintheTRIMmenu,scrollUPorDOWNtohighlighttheTrimSwitch
Number [STEP] you would like to change. Choose from TRM1 [STEP],
TRM2 [STEP], TRM3 [STEP], TRM4 [STEP] or TRM5 [STEP].
2) Press the ENTER key, then scroll UP or DOWN to change the desired Trim
Switch Step value.
STEP setting range is 1 to 100. The default setting is 1 or 5 depending on the
Trim Switch Number. The Step value is a percentage of travel.
3) Repeat step 2 to change any other desired Trim Step values.
6) Press the ENTER key, then repeat steps 4 and 5 to program any other desired Trim Switch Function Assignments.
Changing the Trim Switch Direction of Travel:
The direction that the Trim Switches move the servos or function values can be changed from Normal to Reverse. In Normal mode,
the Trim Switches will move the servos toward the High Side or Increase function values when the Trim Switches are pushed
Forward. In Reverse mode, the Trim Switches will move the servos toward the Low Side or Decrease function values when the
Trim Switches are pushed Forward.
1) FromwithintheTRIMmenu,scrollUPorDOWNtohighlighttheTrimSwitch
Number [REV] you would like to change. Choose from TRM1 [REV],
TRM2 [REV], TRM3 [REV], TRM4 [REV] or TRM5 [REV].
TYP I
TYP II TYP III TYP IV TYP V TYP VI TYP VII TYP VIII TYP IX TYP X
Model Type
TRM1
TRM2
TRM3
TRM4
TRM5
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
TRIM ST
TRIM TH
R-MODE
D/R ST
D/R BR
The table below shows the default Trim Switch functions based on the Selected Car Type. A complete list of functions that can be Assigned to
the Trim Switches are shown in the Trim Switch, Auxiliary Dial and Auxiliary Lever Functions tables on pages 112 and 109.
Function