EXZES ZZ Radio System Manual

38
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
3) Press the ENTER key, then repeat steps 1 and 2 to program any other desired Telemetry Switch Function Assignments.
Although two different functions can be Assigned to the same Telemetry Switch, those functions cannot be controlled
independently.
ASSIGN MENU
{
SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS
}
SYSTEM
Changing the Telemetry Push-Button Switch Control Function and Mode Values:
Follow the information in this section if you've programmed the Telemetry value to SW. If you've programmed the Telemetry
value to TRIM or LEVER, please refer to those specific sections.
UptotwodifferentfunctionscanbeAssignedtoeachTelemetrySwitch(T1andT2)andtheONandOFFbehaviorofeach
TelemetrySwitchcanbechangedtoeitherPUSHorTOGGLEtosuittheprogrammedfunctionandthespecificrequirementsof
your external device.
1) FromwithintheTELEMETRY>SWmenu,scrollUPorDOWNtohighlightthe
Telemetry Switch Number and Function you would like to change. Choose
from T1 [FUNCTION 1 or 2] or T2 [FUNCTION 1 or 2].
2) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredfunction
for the Telemetry Switch Number and Function you highlighted. A list of
functions that can be Assigned to the Telemetry Switches are shown in the
table below.
TYP I
---
ALB
OFFSET
AUX1
AUX2
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
TYP II TYP III TYP IV TYP V TYP VI TYP VII TYP VIII TYP IX TYP X
---
ALB
OFFSET
AUX
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
AUX
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
AUX
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
LAP
INT1
INT2
DOWN
TH-HOLD
R-MODE
*
---
ALB
OFFSET
AUX
LAP
INT1
INT2
DOWN
4WS
R-MODE
*
---
ALB
OFFSET
AUX
LAP
INT1
INT2
DOWN
R-MODE
*
---
ALB
OFFSET
LAP
INT1
INT2
DOWN
4WS
R-MODE
*
*NotaFunction2option.CanonlybeAssignedtoFunction1.
Function
Model Type
The table below shows the functions can be controlled by the two Telemetry Switches:
4) FromwithintheTELEMETRY>SWmenu,scrollUPorDOWNtohighlightthe
Telemetry Switch Number [MODE] you would like to change. Choose from T1
[MODE] or T2 [MODE].
5) PresstheENTERkey,thenscrollUPorDOWNtochangethedesiredTelemetry
SwitchModevalue.ChoosefromeitherTOGGLEorPUSH.
MODEsettingrange is PUSH and TOGGLE. Thedefaultsettingforboth
T1andT2isPUSH.
6) Repeat steps 4 and 5 to change any other desired Telemetry Switch Mode values.
The ON and OFF behavior of each Telemetry Switch can be changed to suit the programmed function and the specific requirements
of your external device. The following Telemetry Switch Modes are available:
TOGGLE - Press the Push-Button Switch on your external device to turn the function ON and press the Push-Button Switch
a second time to turn the function OFF.
PUSH - Press and HOLD the Push-Button Switch on your external device to turn the function ON and Release the
Push-Button Switch to turn the function OFF.
Changing the Telemetry Trim Switch Control Function, Step and Reverse Values:
Follow the information in this section if you've programmed the Telemetry value to TRIM. If you've programmed the Telemetry
value to SW or LEVER, please refer to those specific sections.