EXZES ZZ Radio System Manual

40
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
BUZZER MENU
{
AUDIBLE KEY TONES AND ALARMS
}
SYSTEM
The Buzzer function allows you to change the Tone and Volume of many of the audible sounds that the transmitter makes. This
rangesfromsoundsthataremadewhenyoupresstheTrimSwitchesandPush-ButtonSwitches,scrollUPorDOWNorpressthe
ENTER key, Lap and Interval Timer alarms, Telemetry Alert alarms, transmitter Voltage Limit alarm and more.
The Volume can be Increased or Decreased (or Muted) and the Tones can be changed to suit your preference. In addition,
different Tones can be set separately for the first half and the second half of a Tone, making it easier to differentiate between
the two halves.
CLICK
TRIM
CENTER
MULTI
TIMER SW
INT1 TIMER
INT2 TIMER
LAP-PRE
LAP GOAL
DOWN-PRE
DOWN-FIN
UP-1MIN
OFFSET
TLM VOLT
TLM1
TLM2
LIMIT
DESCRIPTION
ControlsKeyPressTones,SuchasENTER,BACK,SELECTandAllPush-ButtonSwitches
ControlsAllTrimSwitchKeyPressTones
Controls the Trim Switch, Auxiliary Dial and Auxiliary Lever Neutral Point Indicator Tones
ControlsthePush-ButtonRotaryDialscrollUPandScrollDOWNTones
Controls the Lap Timer Start and Stop Tones
Controls the First Interval Timer Start and Stop Tones
Controls the Second Interval Timer Start and Stop Tones
Controls the Lap Timer Pre-Alarm Tones
Controls the Lap Timer Goal Alarm Tones
Controls the Countdown Timer Pre-Alarm Tones
Controls the Countdown Timer Final Alarm Tones
Controlsthe1MinuteCountUpTimerAlarmTones
Controls the Offset Function Alarm Tones
Controls the Telemetry Receiver Voltage Alert Alarm Tones
Controls the Telemetry 1 (Default Temp 1) Alert Alarm Tones
Controls the Telemetry 2 (Default Temp 2) Alert Alarm Tones
Controls the Transmitter Limit Voltage Alarm Tones
FUNCTION
The table below shows the functions that the Tone and Volume can be adjusted for:
Changing the Telemetry Lever Control Function and Tweak Values, Continued:
Forexample,ifyouAssignAUX2totheTelemetryLeverandadjusttheTweakvaluesto+50and-50,theAuxiliary 2 servo will be
centered when the Lever on your external device is centered and will travel 50% in one direction when the Lever on your external
deviceismovedUpandtravel50%intheotherdirectionwhentheLeveronyourexternaldeviceismovedDown.Alternately,ifyou
Assign TRIM
ST to the Telemetry Lever and adjust the Tweak values to +50 and -50, the Lever on your external device will control
Steering Trim from 0% to 50%.
4) FromwithintheTELEMETRY>LEVERmenu,scrollUPorDOWNtohighlighteitherT1[TWEAK(H)]>+100orT2[TWEAK
(H)]>+100.
5) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredHighSideTweakvalue.IncreasingtheTweakvaluewill
Increase travel in the High Side direction and Decreasing the Tweak value will Decrease travel in the High Side direction.
UsingaNegativevaluewillchangethedirectionoftravel.
ASSIGN MENU
{
SWITCH, DIAL, LEVER AND TELEMETRY FUNCTION ASSIGNMENTS
}
SYSTEM
T1TWEAK(H)andT2TWEAK(H)settingrangeis-100to+100.Thedefaultsettingforbothis+100.
6) ScrollUPorDOWNtohighlighteitherT1[TWEAK(L)]>-100orT2[TWEAK
(L)]>-100.
7) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredLowSide
Tweak value. Decreasing the Tweak value will Increase travel in the Low
Side direction and Increasing the Tweak value will Decrease travel in the
LowSidedirection.UsingaPositivevaluewillchangethedirectionoftravel.
T1TWEAK(L)andT2TWEAK(L)settingrangeis-100to+100.Thedefaultsettingforbothis-100.