EXZES ZZ Radio System Manual

44
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
AUX TYPE MENU
{
AUXILIARY CHANNEL OPERATING MODE
}
SYSTEM
Changing the Auxiliary Channel Operating Mode:
1) FromwithintheSYSTEMmenu,scrollUPorDOWNtohighlighttheAUXTYPE
menu.
2) PresstheENTERkeytoopentheAUXTYPEmenu.AUX1>NORwillbe
highlighted.
3) ScrollUPorDOWNtochoosewhichAuxiliaryChannelyouwanttochange
theOperatingModefor,eitherAUX1orAUX2.
4) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredAuxiliary1
or Auxiliary 2 Operating Mode.
AUX1andAUX2settingrangeisNOR,POINT,CODEandCODE10.ThedefaultsettingforbothAUX1andAUX2isNOR.
Changing the Number of Points Value:
After changing the Auxiliary 1 or Auxiliary 2 Operating Mode to POINT, you are able to change the number of points you want the
servo to travel through. For example, if you want to be able to cycle your servo from 0 to 16 to 34 to 54 degrees and back again,
choosePOINT>4.
POINT setting range is 2 to 6. The default setting is 2.
1) Afterchoosing the POINT option, scrollUP or DOWN to the desired POINT
value,eitherAUX1POINTorAUX2POINT.
2) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesirednumber
of Point positions to program.
WhenAUX1andAUX2valuesaresettoNOR,CODEorCODE10,POINToptionscannotbeprogrammed.
IMPORTANT: When set to POINT, please observe the following: We recommend using either the Auxiliary Dial or one of
the Trim Switches to operate the Auxiliary channel. The Auxiliary Lever is not suitable for use in this situation. In addition,
the Step value for the Auxiliary Dial and/or Trim Switch should be set to 1, otherwise the transmitter won't cycle properly
through the programmed Points.
The Auxiliary Type function allows you choose the Operating Mode for Auxiliary 1 and Auxiliary 2, making it possible to change the
way these two Auxiliary channels function.
This section details how to change the Operating Mode of the two Auxiliary channels. For details about programming and
usingeachoftheAuxiliaryfunctions,seethePOINTAUX1Menusectiononpage70,thePOINTAUX2Menusectionon
page 71 or the CODEAX1 and CODEAX2 Menu section on pages 102 and 103.
The Operating Mode of Auxiliary 1 and Auxiliary 2 can be changed to suit your specific requirements. The following Operating
Modes are available:
NOR - When selected, the Auxiliary channel(s) operate as Normal proportional linear channels, like the Throttle or Steering
channels.
POINT-Whenselected,uptosixPointpositionscanbeprogrammedalongtheentirelengthofservotravel.Youarethen
able to cycle back and forth through those Point positions. This option is ideal if your model requires a three or more position
switch to operate a feature. This mode is not proportional. It's a 'Stepping' mode.
CODE - This option is for use with SSL-compatible accessories, such as an ESC, whose Programming Parameters can be
changed directly via the transmitter. For example, you can change the ESC's Driving Modes directly using the Auxiliary Dial to
suit different conditions while you're driving. This mode allows you to program up to 5 CODE functions per Auxiliary channel.
CODE10 - This option is the same as the CODE option above, but allows you to program up to 10 CODE functions per Auxiliary
channel.UsethismodewithSSL-compatibleaccessoriesthatrequiremorethan5CODEfunctionsforoperation.
DependingontheCarType selected intheTYPEmenu,Auxiliary 2
options may not be available. This is normal.