EXZES ZZ Radio System Manual

50
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
Changing the Throttle Slow Value:
The Throttle Slow function allows you to variably limit Throttle channel travel when both the Low Voltage Alert and Low Voltage
Limit alarms sound to slow the maximum speed of your model, making is safer to operate until you are able to stop and recharge
the transmitter battery. Programming this function is optional, but it's recommended for added safety.
BATT MENU
{
LOW VOLTAGE ALERT AND LIMIT ALARMS
}
SYSTEM
1) FromwithintheBATTmenu,scrollUPorDOWNtohighlightTHSLOW>OFF.
TH SLOW setting range is OFF or ON. The default setting is OFF.
2) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredThrottle
Low value. When set to ON, the maximum Throttle travel will be limited to
approximately 1/2 throttle when the Low Voltage Alert alarm value is reached
and will be limited to approximately 1/4 throttle when the Low Voltage Limit
alarm value is reached. When set to OFF, the Throttle will operate normally
regardless of which Low Voltage Alarm value is reached.
Turning Telemetry Data Recording ON and OFF:
1) FromwithintheSYSTEMmenu,scrollUPorDOWNtohighlighttheLOGSETUP
menu.
Telemetry Data Recording
The Telemetry Data Recording function records Telemetry Data when the Lap Timer is Started. When the Lap Timer is Stopped,
Telemetry Data Recording is also Stopped. One Telemetry Data Log is kept in memory at a time and will be available for viewing
even after the transmitter is turned OFF. When the Lap Timer is Started again, the current Telemetry Data Log will be erased and
anewoneStarted.IfyouwanttoSavethecurrentTelemetryDataLog,usetheSaveLogoptioninthePCLINKmenu.
Prior to turning the Telemetry Data Recording function ON, you must turn Telemetry ON. For more information, see the
Turning the Telemetry Function ON and OFF section on page 29.
LOG SETUP MENU
{
TELEMETRY DISPLAY AND RECORDING OPTIONS
}
SYSTEM
TheLOGSETUPmenuallowsyoutoturnTelemetryRecordingONandOFFandconfigurehowTelemetryDataisdisplayedon
theTELEMETRYscreen.Forexample,youareabletochangethevaluesatwhichthedifferentTelemetrySensoralarmssound,
change how Speed and RPM are displayed and much more. Telemetry 1 and Telemetry 2 can be completely customized to read
differenttelemetryvaluesotherthanTemperature.You'reabletorenameTelemetry1andTelemetry2,customizetheUnitvalue
and adjust the Offset and Rate to match the specific requirements of the TelemetrySensor(orSensors)you'reusing.Youcan
evencustomizeTelemetry1andTelemetry2Pop-Upmessages.
WhenonlytheDISPLAYisturnedONusingtheDISPLAYkey,theEXZESZZcanbeplacedinReceiverMode,allowingittoBind
with another Sanwa FH3 or FH4T transmitter and read Telemetry Data from it. For example, if using an FH4T transmitter like
MT-4SorMT-4,TelemetryDatacanbeviewedontheEXZESZZ'sTELEMETRYscreen,or,ifusinganFH3transmitterlikeMX-3X
orM11Xthatdoesn'tsupportTelemetry,SteeringandThrottleOutputDatacanstillbeviewedontheEXZESZZ'sTELEMETRY
screen. This capability allows the EXZES ZZ to be used as a separate Telemetry Viewer and Recorder.
For information about saving Telemetry Data to a PC, see the Saving the Telemetry Data Log section on pages 61 and 62. For infor-
mationaboutusingtheTELEMETRYscreenandviewingTelemetryData,seetheTELEMETRYScreenOverviewsectionon
pages 17 and 18.
IMPORTANT: Full Telemetry integration requires the use of an Sanwa 2.4GHz FH4T Telemetry-capable surface receiver or
SSL-compatible ESC (e.g. Super Vortex series ESC), although Throttle and Steering Output Data can still be viewed on the
TELEMETRYscreenandrecordedifusinganFH3orFH4receiver.