EXZES ZZ Radio System Manual

67
TR
EXZES ZZ
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
SETUP MENU OVERVIEW SETUP
BASICModemustbeturnedOFFtoaccesstheSETUPmenu.Formoreinformation,seetheTurningBASICModeONand
OFF section on page 20. In addition, depending on the Car Type chosen, some Function Programming Value Names may
differ from those shown in this section.
To access the various SETUP menu Programming Menus, turn the transmitter
ON,presstheSELECTswitchtohighlighttheSETUPmenu,thenpresstheENTER
keytoopentheSETUPmenu.
ScrollUPorDOWN to highlight the desired Programming Menu, then press the
ENTER key to open that menu.
EPA
SUBTRIM
REV
POINT AX1
POINT AX2
MOA MIX
4WS MIX
FEELING
F/S
B-F/S
LAP TIMER
INT1
INT2
DOWN
PG. 67
PG. 68
PG. 69
PG. 70
PG. 71
PG. 71
PG. 73
PG. 74
PG. 74
PG. 75
PG. 77
PG. 78
PG. 78
PG. 79
MENU
PAGE #
MENU DESCRIPTION
Adjust Channel End Points to Balance Servo Travel
Adjust Servo Centering to Center the Servo Horns
Change the Direction of Servo Travel
Adjust Auxiliary 1 Point Values to Change the Servo Stepping Behavior
Adjust Auxiliary 2 Point Values to Change the Servo Stepping Behavior
Adjust and Change Dual Motor Mixing options (Crawler Car Types Only)
Adjust and Change Four Wheel Steering Mixing Options (Crawler Car Types Only)
Adjust Steering and Throttle Channel Latency Values
Program Fail Safe Settings
Program Receiver Battery Fail Safe Settings to Ensure Optimum Servo Performance
Program the Lap Timer Goal Time, Pre-Alarm and Lap Timer Start Options
Program Interval Timer 1 and Change its Start Options
Program Interval Timer 2 and Change its Start Options
Program the Count-Down Timer and Change its Start Options
ThefollowingProgrammingMenusareavailablewithintheSETUPmenu:
The End Point Adjustment function allows you to adjust servo travel in each direction. This makes it possible to balance servo
travel in both directions and set the maximum desired amount of servo travel. For example, on a gas-powered model, if you pull
the Throttle Control Stick and the carburetor does not open completely, you can Increase the Throttle High End Point Adjustment
so that the carburetor opens completely. Another example is with steering. If your model turns sharper to the Right than to the Left,
you can Increase the Steering Left End Point Adjustment to balance the steering.
The End Point Adjustment function can be adjusted for the Steering channel (Right and Left), the Throttle channel (High and
Brake), the Auxiliary 1 channel (High and Low) and the Auxiliary 2 channel (High and Low).
Changing the Channel End Point Adjustment Percentage Values:
1) FromwithintheSETUPmenu,scrollUPorDOWNtohighlighttheEPAmenu.
End Point Adjustment percentage values should not be increased to the point where your
linkages and servos bind when moved all the way to the Right or Left. Binding will cause
the servos to 'buzz', resulting in a quicker loss of receiver battery power and eventual damage to
the servos or to your model.
EPA MENU
{
CHANNEL END POINT ADJUSTMENTS
}
SETUP
IMPORTANT: Before making End Point Adjustments, the servo horn needs to be centered. Install the servo horn onto the servo,
making sure it's as close to being centered as possible, then use the Servo Sub-Trim function to center the servo arm exactly.
Formoreinformation,seetheSUBTRIMMenusectiononpages68and69.
SYSTEM