EXZES ZZ Radio System Manual

70
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
3) ScrollUPorDOWNtohighlightthedesiredServoReversingvalueyouwould
like to change.
4) PresstheENTERkey,thenscrollUPorDOWNtochangetheServoReversing
value. Choose from either NOR (Normal) or REV (Reverse).
5) Press the ENTER key, then repeat steps 3 and 4 to change any other desired
Servo Reversing values.
ST,TH,AUX1andAUX2settingrangeisNORandREV.ThedefaultsettingforallchannelsisNOR.
POINT AUX1 MENU
{
AUXILIARY 1 POINT VALUES
}
SETUP
The Point Auxiliary function allows you to program the Auxiliary 1 servo to move up to 6 different Points along its travel, then cycle
through those Points using one of the Trim Switches or the Rotary Dial. For example, if your model requires a separate 3-position
or more switch to operate a feature, the Point Auxiliary function can be customized to control this. This section details how to
change the actual Point values. For example, if you have 4 Points programmed, you can change the Point values to cycle your
servo from 0 to 16 to 34 to 54 degrees and back again.
UseoneofthefiveTrimSwitchesortheAuxiliaryDialtocyclethroughthePointPositionswhileyou'redriving.TheAuxiliaryLever
is not suitable for use in this situation. The Point Auxiliary function can be toggled OFF and ON while you're driving by Assigning
AUX1tooneofthethreePush-ButtonSwitches.
Prior to programming the Auxiliary 1 Point values, you must first change the Auxiliary Channel Operating Mode to
POINT,thenchoosethenumberofPointsyouwanttoprogram.Formoreinformation,seetheAUXTYPEMenusection
on page 44.
The Step value for the Auxiliary Dial or Trim Switch should be set to 1, otherwise the transmitter won't cycle properly through
the programmed Points. For more information, see the Changing the Trim
Switch Step Value section on page 34 or the Changing the Auxiliary Dial Step
Value section on page 35.
Changing the Auxiliary 1 Point Values:
1) FromwithintheSETUPmenu,scrollUPorDOWNtohighlightthePOINTAX1
menu. In the example shown in this section, we've programmed 4 Points in
theAUXTYPEmenu.
REV MENU
{
SERVO REVERSING
}
SETUP
2) Press the ENTER key to open the POINT AX1 menu. The cursor will default to
P1>L94andthecurrentPointwillbehighlighted.
P1 though P6 setting range is H100 to L100. The default setting for P1 is L100, for P2 is L60, for P3 is L20, for P4 is H20, for P5
is H60 and for P6 is H100. These values are a percentage of Auxiliary 1 servo travel.
3) Scroll UP or DOWN to highlight the desired Point value you would like to
change.
4) Press the ENTER key, then scroll UP or DOWN to change the Point value.
Choosing an H or L value will determine the direction the servo travels.
5) Press the ENTER key, then repeat steps 3 and 4 to change any other desired
Point values.
6) CycleforwardandbackwardthroughthePointsusingtheAuxiliaryDial(default)ortheTrimSwitchyouAssignedAUX1to.You
will notice that as you cycle through the Points, the current Point will be highlighted and in addition, the current Point will be
displayed in a pop-up window.