EXZES ZZ Radio System Manual

78
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
This section covers both the INT1 and INT2 menus, since programming each of them is exactly the same. Choose either the
INT1 or the INT2 menu depending on which of the two Interval Timers you want to program.
LAP TIMER MENU
{
VIEW LAP TIMES AND CHOOSE LAP TIMER OPTIONS
}
SETUP
Stopping the Lap Timer:
1) To Stop the Lap Timer, press and HOLD the Lap Timer Switch for 3 seconds. An audible Double-Tone will sound and LAP
[
STOPPED
]
will be displayed momentarily in a pop-up window, indicating the Lap Timer is stopped.
The Cumulative Time cannot be manually cleared. It will be automatically cleared when the Lap Timer is put in
Standby again.
Viewing Lap Times:
The Cumulative Lap Time, the Best Lap Time and the Average Lap Time, in addition to up to 154 individual Lap Times can be
viewedontheTELEMETRYscreenLAPpage.
1) FromtheSTATUSscreen,scrollUPorDOWNtoopentheTELEMETRYscreen.PresstheSELECTswitchRightorLefttoopen
the LAP page.
2) PresstheENTERkey,thenscrollUPorDOWNtoviewtheindividualLapTimes.
Lap Times are stored until you Restart the Lap Timer. When the Lap Timer is Restarted, old Lap Times are Cleared and
new Lap Times are Stored.
INT1 AND INT2 MENU
{
INTERVAL 1 AND INTERVAL 2 TIMERS
}
SETUP
The Interval Timer function is used to notify you when a set Interval elapses while you're driving. When the Interval Time is
reached,anaudibleDouble-Tonewillsound,thentheIntervalTimerwillResetandbegincountingUpagainfromzero.Interval
Times are displayed in the following format: 00':00".00 (Minutes : Seconds : 1/100th of a Second). The Interval Timer can be
programmed to work independently or programmed to work along with the Lap Timer function.
There are two Interval Timers. These Interval Timers can be Started and
Stopped independently by Assigning each one to a different Push-Button
Switch or they can be Started and Stopped simultaneously by Assigning
both of them to the same Push-Button Switch. If desired, different Tones can
be Assigned to each Interval Timer to differentiate them. In addition, the
Throttle Control Stick can be programmed to Start the Interval Timer(s).
In the default configuration, Interval Timer 1 is Started and Stopped along
with the Lap Timer, using the Lap Timer Switch (Push-Button Switch Sw3).
Setting the Interval Timer:
1) FromwithintheSETUPmenu,scrollUPorDOWNtohighlighteithertheINT1
or the INT2 menu depending on which Interval Timer you want to program. In
this section, we show programming Interval Timer 1.
2) PresstheENTERkeytoopentheINT1menu.INTERVAL>00'willbehighlighted.
3) ScrollUPorDOWNtohighlightthedesiredIntervalTimervalueyouwouldlike
to change, either 00' (Minutes) , 00" (Seconds) or 00 (1/94th Seconds).
4) PresstheENTERkey,thenscrollUPorDOWNtochoosethedesiredInterval
Timer value.
5) Press the ENTER key again, then repeat steps 3 and 4 to change any other
desired Interval Timer values.
INT1 and INT2 INTERVAL setting range is 00:00:00 to 99:59:90. The default setting for both Interval Timers is 00:00:00.
Choosing the Optional Throttle Control Stick Start:
The Throttle Control Stick can be used to Start the Interval Timer after the Interval Timer as been placed in Standby by pressing
the Push-Button Switch it's Assigned to. This is much more convenient and accurate than pressing the Push-Button Switch again
to Start the Interval Timer when you're trying to start your race.