EXZES ZZ Radio System Manual
8
EXZES ZZ
TR
2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
The receiver's Nominal Input Voltage is 3.7 to 7.4 volts. A 2S Li-Po or 2S Li-Fe battery pack can be used to power the receiver
without the use of a voltage regulator. In addition, this allows you to take advantage of the higher torque and speed provided by
using 7.4 volt digital servos.
**
Use a 2S Li-Po or 2S Li-Fe battery pack ONLY if your servos are rated to handle the higher voltage!
**
• WesuggestBindingthetransmitterandreceiverandmakingallreceiverconnectionstocheckforcorrect
operation prior to mounting the receiver in your model.
• Routethereceiverantennaupthroughaplastictubesothatitisintheverticalposition.Do not bend the
reception wire. Reception performance decreases if the reception wire is bent. Do not pull on the antenna
with force. Do not cut or extend the antenna. The coaxial cable can be bent into gentle curves, however, do
not bend the coaxial cable acutely, or repeatedly bend it, or the antenna core can be damaged.
• Toprotectthereceiverfromvibrationandotherdamage,werecommendwrappingthereceiverinshock
absorbing foam or using double-sided foam tape when installing it in your model.
• As a safety precaution, set your model on a stand so the wheels are off the ground before turning on your radio control system.
Bind LED Condition Indicator:
The receiver's Bind LED will alert you to various receiver conditions, as shown in the below below.
UsethediagramsinthissectiontomakereceiverconnectionsandtofamiliarizeyourselfwiththeRX-4722.4GHzFH4TSuper
Response SSL receiver included with your EXZES ZZ radio control system. Descriptions of the features can be found in the Trans-
mitter and Receiver Features Descriptions section below and on the next two pages.
Bind Button
= Signal
= Positive
= Negative
Bind LED
Coaxial Cable
Antenna
Reception Wire
Steering
Channel 1
Throttle
Channel 2
Auxiliary 1
Channel 3
Auxiliary 2
Channel 4
On/Off Switch
'AA' Dry Cell Battery Holder,
3.7v to 7.4v Ni-Cd/Ni-MH Battery Pack or
2S Li-Po or Li-Fe Battery Pack
On/Off Switch
To Battery
To Motor
ESC
Throttle
Channel 2
Glow/Gas
Setup
ESC
Setup
Antenna: Transmits the signal from the transmitter to the receiver in the model.
Antenna Reception Wire: The portion of the receiver antenna that receives the transmitter signal. The Antenna Reception Wire
should never be bent or it could be damaged and limit the range of your model.
Auxiliary Dial: The Auxiliary Dial can rotate 360º and is programmable to perform a different function depending on what function
is Assigned to it. In the default configuration, it controls Auxiliary 1 High and Low servo travel.
Auxiliary Lever: The Auxiliary Lever is programmable and will perform a different function depending on what function is Assigned
to it. In the default configuration, it controls Auxiliary 2 High and Low servo travel.
RECEIVER OVERVIEW DIAGRAM, CONNECTIONS AND MOUNTING GENERAL
TRANSMITTER AND RECEIVER OVERVIEW DIAGRAM DESCRIPTIONS GENERAL
Blue
Blue
Red & Blue
Red
Receiving RF Signal
Binding Operation
Receiver Battery Fail Safe Activates
No RF Signal After Receiver Battery Fail Safe Activates
LED COLOR
RECEIVER STATUS
LED CONDITION
ON
Slow Flash/Fast Flash
Flash
ON
Antenna Tube
Coaxial Cable
Antenna
Reception Wire
If using a Sanwa Super Vortex series ESC or other SSL-compatible device, plug the ESC or device into the SSL slot, otherwise
SSL features and Telemetry Data will not be available. All other ESC's should be plugged into CH 2.
SSL
IMPORTANT: The RX-472 2.4GHz FH4T Super Response SSL receiver does not feature full Telemetry support on its own (e.g.,
Temperature data and RPM/Speed data). Full Telemetry capability is supported only when used with a Sanwa Super Vortex
series ESC plugged into the SSL slot. This is due to the fact that full internal Telemetry support slows the Response Time of
the receiver and we've chosen to include a receiver that will allow you fastest Response Time possible for competition racing.