Installation Instructions

10
Before Using
Note
• If the connector is disconnected due to a vibration during operation, it can cause runaway. Connect the connector
of the receiver, servos and switches securely.
• Because the receiver is susceptible to vibration, impact and water, make sure to take measures for vibration-proof
and waterproof. Negligence of taking these measures can cause runaway.
• When installing the receiver, keep the receiver away from a carbon chassis and metallic chassis.
• If metal parts installed on an RC car touch each other, it can cause noise that affects reception performance and it
can cause runaway.
• Make sure to install a noise killer condenser on the brush motor for electric RC cars. Without a noise killer
condenser, it can cause noise and runaway.
• For R/C System parts such as the transmitter, receiver, servos, ESC (FET Speed Controller) and transmitter
battery, use genuine SANWA products.
*When combining products other than genuine SANWA products, modifying, adjusting or exchanging parts is
done at a place other than SANWA, we do not take any responsibility.
ABOUT CONNECTION SETUP
、
■Case of connecting PGS servo to 2 SSL ports
■Case of connecting PGS servo and SUPER VORTEX Gen2 / PRO / Stock / SV-D2 to SSL port
●Connection example in case of using in EP car
Please refer the below picture for receiver and servo connection
Switch harness
Connect the receiver battery
Connection with BATT
Connection with
CH2
Connection with CH1
Power battery
Motor
ESC / FET speed controller
Steering servo
Throttle servo
Connection with CH1
Connection with CH2
Steering servo
CH2
BATT
CH1
CH2
BATT
CH1
SUPER VORTEX Gen2/PRO
/Stock/SV-D2
●Set AUX TYPE of the transmitter for both AUX1, AUX2 to CODE 10.
AUX1 CODE10: Setting of SUPER VORTEX Gen2 / PRO / STOCK / SV-D2 can be from the transmitter.
AUX2 CODE10: Setting of each of the parameters of PGS servo can be from transmitter.
Note) In SUPER VORTEX Gen2 / PRO / STOCK / SV-D2, do not assign function to CODE 10 of AUX2 by code
assign of PROGRAM BOX Gen2. It interferes with CODE 10 of AUX2 of PGS servo and suitable
setting cannot be done.
Note) Set SSL－CH of PGS servo to [1].
(Factory setting of PGS servo is [1].)
Note) CODE of AUX2 is used for SUPER VORTEX ZERO / SUPER VORTEX TYPE-D /
SUPER VORTEX SPORT. It interferes with CODE 10 of AUX2 of PGS servo and
suitable setting cannot be done. Therefore, it cannot be used along with SSL of PGS servo.
Note)When Connecting PGS servo with SGS-02 cannot change setting at the same time.
When using SGS-02, Gain connector connect to SSL port.
*Please DO NOT connect another devices except SANWA SSL compatible products.
About setting and connection, please refer manuals of SSL compatible product.
Short Y harness
Steering servo
PGS servo：SSL - CH1 setting
SSL Port
Connect the receiver battery
●Set AUX TYPE of AUX2 of the transmitter to CODE 10.
AUX2 CODE10: Setting of each of the parameters of PGS servo can be done from the transmitter.
Note) Set SSL－CH of PGS servo used in steering servo to [1].
Set SSL－CH of PGS servo used in throttle servo to [2].
(Factory setting of PGS servo is [1].)
Note) In case of setting each parameter by the function of CODE10 of AUX2, setting of PGS
servo of SSL－port set by CODE1 of AUX2 can be directly changed from the transmitter.
PGS servo not specified by CODE1 of AUX2 works on the parameters saved inside.
PGS servo: SSL - CH1 setting
Steering servo
Switch harness
Short Y harness
Throttle servo
PGS servo: SSL 2 CH2 setting
SSL Port
Other Empty Port
*Please, refer on our Website about any other examples. http://www.sanwa-denshi.com
*When using PGS Servo with SGS-02,
PGS servo cannot set by CODE10 at the same time.
Only SGS-02 can be set when connect with PGS servo.