CLT-2412E-NEW 7/5/02 6:21 PM Page 1 2.4 GHz Cordless Telephone with Caller ID CLT-2402 CLT-2412 Instruction Manual Important Charge the handset battery for 12 continuous hours prior to first use. SANYO Canada Inc. www.sanyocanada.
CLT-2412E-NEW 7/5/02 6:21 PM Page 2 TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Checking package contents Modular jack . . . . . . . . . . . Installation tips . . . . . . . . . Battery setup . . . . . . . . . . . Telephone line connection Mounting on a wall . . . . . Digital Security System . . . . . . . . . . . . . . . . . .
CLT-2412E-NEW 7/5/02 6:21 PM Page 4 INTRODUCTION GETTING STARTED Congratulations on your purchase of this Sanyo cordless telephone. Your Sanyo 2.4 GHz cordless telephone is a fine-quality home communications product. It is carefully designed and produced by a world leader of consumer and industrial electronics equipment. With proper maintenance and care, it will provide you with years of enjoyment and convenience. Checking the package contents Make sure your package includes the items shown here.
CLT-2412E-NEW 7/5/02 6:21 PM Page 6 GETTING STARTED GETTING STARTED Battery setup 1. Remove the battery compartment cover on the handset, insert the battery, plug the cord into the jack (inside the compartment) and replace the cover. 2. Set the handset RINGER switch to ON, and place handset in the base. 3. Plug the AC adpator into the POWER DC 12V jack on the back of base and the other end into an electrical outlet. The CHARGE/PAGE indicator comes on verifying the battery is charging.
CLT-2412E-NEW 7/5/02 6:21 PM Page 8 NAMES AND CONTROLS INITIAL PROGRAMMING Handset Earpiece Incoming call visual alert LED VOLUME keys LCD screen 7-10-11/HOLD key CID ▲ or ▼ key TALK/CALL BACK key (also used to END a call) Area code setting For proper Caller ID operation, you must program your area code. 1. Make sure the phone is OFF (not in TALK mode). 2. Press FLASH/PROG until S E T A R E A C O D E - - - shows on screen. 3. Enter your 3-digit area code using the number keys. 4.
CLT-2412E-NEW 7/5/02 6:21 PM Page 10 BASICS INITIAL PROGRAMMING 1. 2. 3. 4. Make sure the phone is OFF. Press FLASH/PROG until D E F A U L T S E T T I N G 1 Y E S 2 N O shows on screen. 2 N O is factory set. Press CID ▲ or ▼, or the 1 or 2 key to select your choice. Press FLASH/PROG to confirm. BASICS BASICS * A subscription is required from your local phone company to receive Caller ID information on your phone. See Caller ID Features , page XX. 2. Press TALK/CALL BACK to answer the call.
CLT-2412E-NEW 7/5/02 6:21 PM Page 12 BASICS BASICS Tip: Do not use TALK/CALL BACK to activate custom calling services such as Call Waiting, or you will hang up the phone. CHAN (Channel) key While talking, you might need to manually change the channel in order to get rid of static. Press and release the CHAN key to switch to the next clear channel. HOLD key Press HOLD to put a call on hold. To release a line on hold, press HOLD again or pick up an extension phone.
CLT-2412E-NEW 7/5/02 6:21 PM Page 14 CALLER ID FEATURES CALLER ID FEATURES This phone receives and displays incoming call information transmitted by your local phone company. This information can include the phone number and/or the name, date and time. The phone can store up to 40 calls for later review.
CLT-2412E-NEW 7/5/02 6:21 PM Page 16 CALLER ID FEATURES DIRECTORY Dialing a Caller ID number 1. Make sure the phone is OFF (not in TALK mode). 2. Use CID ▲ or ▼, to scroll to the desired Caller ID entry. 3. Use the 7-10-11 key to show the phone number in proper digits if necessary. 4. Press TALK/CALL BACK. The number dials automatically. You may store up to 10 numbers (up to 24-digits) in memory for quick dialing.
CLT-2412E-NEW 7/5/02 6:21 PM Page 18 DIRECTORY DIRECTORY Inserting a pause in the dialing sequence Press PAUSE twice to insert a delay in the dialing sequence of a stored telephone number when a pause is needed to wait for a dial tone (for example after you dial 9 for an outside line, or to wait for a computer access tone). Each pause counts as 1 digit in the dialing sequence. P shows on screen. Note: Make sure to press PAUSE twice to enter a pause.
CLT-2412E-NEW 7/5/02 6:21 PM Page 20 CHANGING THE BATTERY RECYCLING NICKEL-METAL HYDRIDE BATTERIES Battery replacement and handling When the operating time becomes short even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. NICKEL-METAL HYDRIDE BATTERIES MUST BE DISPOSED OF PROPERLY. Please take your used battery pack to a store that recycles Ni-MH batteries.
CLT-2412E-NEW 7/5/02 6:21 PM Page 22 SOUND SIGNALS LCD SCREEN MESSAGES The following indicators show the status of a message or of the phone. A long warbling tone Signals an incoming call Single Tone A key is pressed ERROR Two Long Beeps Confirmation tone One short beep and one long beep Page signal Caller information has been interrupted during transmission or the phone is excessively noisy. ENTER NAME Prompt telling you to enter name in directory.
CLT-2412E-NEW 7/5/02 6:21 PM Page 24 TROUBLESHOOTING TROUBLESHOOTING • Is the battery pack installed correctly? • Did the handset beep when you pressed TALK/CALL BACK? Did the VOICEMAIL/IN USE indicator come on? The battery may need to be charged. Dial tone is OK, but cannot dial out • Make sure the TONE/PULSE switch on the back of the base unit is set to TONE or PULSE according to your phone service. Handset does not ring • Make sure the RINGER switch on the handset is turned to ON.
CLT-2412E-NEW 7/5/02 6:21 PM Page 26 MAXIMIZE BATTERY PERFORMANCE The freedom that your cordless telephone can offer is fully dependent on the performance of the rechargeable battery in the handset. To maximize the battery performance, follow these guidelines: Charge it for a full 12 hours Before initial use of your new battery, charge it for 12 hours continuously. The proper initial charging is very important to maximize the battery performance.
CLT-2412E-NEW 7/5/02 6:21 PM Page 28 WARRANTY TECHNICAL INFORMATION connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. some cases, the company’s inside wiring associated with single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
CLT-2412E-NEW 7/5/02 6:21 PM Page 30 SOS HELP LINE At Sanyo, fulfilling the needs of our customers is a priority. That’s why we created our SOS customer service program that guarantees satisfaction. NATIONWIDE CUSTOMER SUPPORT SOS is there to help you. Our friendly and knowledgeable product specialists will quickly answer your questions about setup and use of Sanyo telephone products.