L8HBM_XE(HARD)(GB).book 1 ページ ２００６年２月６日 月曜日 午前１０時５２分 INSTRUCTION MANUAL DSR-3706PA Digital Video Recorder with Multiplexer Function About this manual Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference. ● Refer to the included CD-ROM for the German, French, Spanish and Italian “INSTRUCTION MANUAL”. ● Die “BEDIENUNGSANLEITUNG” in den Sprachen Deutsch, Französisch, Spanisch und Italienisch finden Sie auf der beiliegenden CD-ROM.
L8HBM_XE(HARD)(GB).book 1 ページ ２００６年２月６日 月曜日 午前１０時５２分 Table of Contents Foreword Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 These must be followed for safety reasons . . . . . . . . 3 Follow the points outlined below for proper use . . . . 5 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Names and functions of parts (front panel) . . . . . . .
L8HBM_XE(HARD)(GB).book 2 ページ ２００６年２月６日 月曜日 午前１０時５２分 Table of Contents B Recording area menu description. . . . . . . . . . . . . 43 E Network settings . . . . . . . . . . . . . . . . . . . . . . . . . . .69 b Verifying the capacity of the recording areas . . . . B-1 Changing the normal recording area and the alarm recording area . . . . . . . . . . . . . . . B-2 Archive area full reset . . . . . . . . . . . . . . . . . . . . . C Recording conditions menu description . . . . . . .
L8HBM_XE(HARD)(GB).book 3 ページ ２００６年２月６日 月曜日 午前１０時５２分 Safety precautions These must be followed for safety reasons Warning b Do not use if the unit emits smoke, or while abnormal sounds and smells are detected. Using in an abnormal condition may cause electrocution and fires. Immediately remove the power cable from the outlet, confirm that there no smoke is emitting and request repairs at the dealership or factory shop where this unit was purchased. Do not attempt repairs on your own.
L8HBM_XE(HARD)(GB).book 4 ページ ２００６年２月６日 月曜日 午前１０時５２分 Safety precautions Caution b Delivery and portability • Never move this unit while the power is turned on. • Remove the power cable from the outlet, confirm that the connection cable has been removed, and store in original packaging before delivering. Deliver using a method that causes the least amount of shock and/or damage to this unit. Also, do not drop this unit. b Do not expose to extreme temperatures or temperature variations.
L8HBM_XE(HARD)(GB).book 5 ページ ２００６年２月６日 月曜日 午前１０時５２分 Safety precautions Follow the points outlined below for proper use b Hard disk This unit is loaded with a hard disk drive. Stored data on this unit may be damaged/lost through hard-disk breakdowns caused by shock/vibration. Follow the items outlined below when placing, transporting, and operating this unit. Warning G This unit is designed to be positioned horizontally. Do not position vertically.
L8HBM_XE(HARD)(GB).book 6 ページ ２００６年２月６日 月曜日 午前１０時５２分 Safety precautions b Back up battery • A lithium battery (fixed) is built into this unit. Supplying power for more than 48 hours after setting the date and time will allow the internal power source to sustain the set time for 30 days. • The battery is expected to last for approximately 5 years if the unit is used regularly. • Battery fluid leaks Rinse hands/clothes thoroughly with water in case battery fluid has leaked.
L8HBM_XE(HARD)(GB).book 7 ページ ２００６年２月６日 月曜日 午前１０時５２分 Main Features Accessories b This digital video recorder (DVR) can record video from surveillance cameras to its internal hard disk, and it can display the video on a screen split into six or four fields, both during recording, and playback. Check that you have all the parts shown below.
L8HBM_XE(HARD)(GB).book 8 ページ ２００６年２月６日 月曜日 午前１０時５２分 Names and functions of parts (front panel) DSR-3706PA 1 2 3 4 5 6 7 8 9 1 Power indicator (POWER) On: The power cord at the rear panel of the DVR is inserted in the outlet. Off: The power cord on the rear panel of the DVR is not inserted in the outlet. Fast blinking: Hard disk error. Slow blinking: Cooling fan error. If the indicator is blinking, contact the store where you purchased the DVR.
L8HBM_XE(HARD)(GB).book 9 ページ ２００６年２月６日 月曜日 午前１０時５２分 Names and functions of parts (front panel) J K L M X W W 1 Open 2Pull out Front N P O 2 Q Insert 3 Fold down 1 Lift and (lock) R S T U J Menu button and indicator (MENU) On: The menu is displayed. Off: The EXIT/OSD button is pressed. K Exit/Operation screen display button and indicator (EXIT/OSD) On: Displaying the channel and operations information when switching from the menu screen, etc. to the live image or the playback screen.
L8HBM_XE(HARD)(GB).book 10 ページ ２００６年２月６日 月曜日 午前１０時５２分 Names and functions of parts (rear panel) Basic connections 1 Clear button (ALL RESET) 3 Video input terminal (Video IN) Press to reset the clocks connected to the digital video recorder to their initial values. Connect SANYO protocol cameras (dome or zoom) or generic cameras to these terminals. (P70) ALL RESET Camera (sold separately) 2 Video output terminal (Video OUT) Outputs the image input in the Video input terminal.
L8HBM_XE(HARD)(GB).book 11 ページ ２００６年２月６日 月曜日 午前１０時５２分 Names and functions of parts (rear panel) Alarm and RS-485 connections 1 Alarm input terminals (ALARM IN) 2 Sensor alarm output terminals (SENSOR ALARM OUT) Connecting a switch or security sensor etc. to the terminal of the DVR allows the detection of the intrusion of outsiders when doors etc. are opened and closed. Alarm input settings are necessary.
L8HBM_XE(HARD)(GB).book 12 ページ ２００６年２月６日 月曜日 午前１０時５２分 Names and functions of parts (rear panel) Control terminals (CONTROL) This DVR can be remotely controlled when a remote-control circuit (R1, R2, C) similar to that shown below is connected to the remote-control terminals. • Use a resistance of 1/10 ohms or more and with a D ranking (Precision within ±0.5%). • The remote control cable should be no more than 5 m long.
L8HBM_XE(HARD)(GB).book 13 ページ ２００６年２月６日 月曜日 午前１０時５２分 Preparing for use Turn on the power of the DVR 1 Language, clock settings Connect the supplied power cable. The power indicator turns on, and the monitor displays the "PLEASE SET THE CLOCK !" message. The DVR performs playbacks or searches based on the recording date and time. Select the LANGUAGE/ CLOCK SET using the INITIAL SET in the MAIN MENU, and set the date and time using .
L8HBM_XE(HARD)(GB).book 14 ページ ２００６年２月６日 月曜日 午前１０時５２分 Preparing for use Operation display The operation display shows information necessary for operation, such as the date, time and video quality. The operation display can be hidden. 1 2 3 4 56 7 Changing the position of the operation display Whenever the EXIT/OSD button is pressed, the position of the operation display changes.
L8HBM_XE(HARD)(GB).book 15 ページ ２００６年２月６日 月曜日 午前１０時５２分 Viewing live video using various multi screens Switching to another full-screen video Press the camera selection button (example 2, 6) of the desired camera. The video from Camera 2, then the video from Camera 6 are displayed. Enlarging an image (Plus screen display) 1 Press the PLUS button. One camera image is displayed enlarged. Plus screen PLUS 02 02 06 2 6 05 04 ☞ Refer to P20 for enlarging the images (zoom).
L8HBM_XE(HARD)(GB).book 16 ページ ２００６年２月６日 月曜日 午前１０時５２分 Viewing live video using various multi screens Automatic screen scrolling Viewing on the monitor connected to the MON2 terminal A Automatic full-screen scrolling Press the SEQUENCE button. The live surveillance video scrolls through the cameras in the order of the camera numbers. To stop the automatic scrolling, press the SEQUENCE button once again. Connect a monitor to the MON2 terminal on the rear panel. The display is full-screen only.
L8HBM_XE(HARD)(GB).book 17 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording video to the hard disk The internal hard disk is automatically formatted with recording area, normal recording, recording conditions, etc. Before starting recording, verify the recordable duration for normal recording (List of recording rate and recording times: P83). The formatting can be modified using "Recording settings".
L8HBM_XE(HARD)(GB).book 18 ページ ２００６年２月６日 月曜日 午前１０時５２分 Viewing recorded video This DVR can play video that has already been recorded or currently being recorded in the normal recording area (by normal or timer-controlled recording). Normal recording area (Normal recording area) Full-screen viewing 1 Press the PLAY/STOP button. The " " symbol appears in the operation display area and the video starts playing.
L8HBM_XE(HARD)(GB).book 19 ページ ２００６年２月６日 月曜日 午前１０時５２分 Viewing recorded video Changing the playback speed Viewing still images The corresponding symbol ( , ...) appears in the operation display area for each of these operations. Audio will not be played when changing the playback speed. A Fast-forward/Slow playback Press the STILL button during playback. The image is paused. The " " symbol appears in the operation display area. Press the STILL button once again, to return to normal playback.
L8HBM_XE(HARD)(GB).book 20 ページ ２００６年２月６日 月曜日 午前１０時５２分 Viewing recorded video Enlarged viewing Quad-screen viewing The zoom function is not available in multi-screen, plus screen mode or on the monitor connected to MON2 terminal. If video is recorded from a number of cameras, the recorded videos can be played back in a quad-screen format. 1 1 Press the QUAD button during playback. Videos recorded from camera numbers 1~4 are displayed in quad-screen format. 2 Press the QUAD button repeatedly.
L8HBM_XE(HARD)(GB).book 21 ページ ２００６年２月６日 月曜日 午前１０時５２分 Searching for recorded video Video stored in the normal recording area, alarm recording area or archive area can be located by searching and then played back. Use one of the five search methods to locate the required video. Press the SEARCH button: A Alarm search (P22) SEARCH The screen appears. Searching is not possible during playback and menu display.
L8HBM_XE(HARD)(GB).book 22 ページ ２００６年２月６日 月曜日 午前１０時５２分 Searching for recorded video A Alarm search B Alarm thumbnail search 1 Press the SEARCH button during recording or live video. 1 Press the SEARCH button during recording or live video. 2 Turn the J-dial, select "ALARM SEARCH", and turn the S-dial clockwise. The screen is displayed. The eight most recent alarm recordings are displayed. 2 Turn the J-dial, select "ALARM THUMBNAIL SEARCH", and turn the S-dial clockwise.
L8HBM_XE(HARD)(GB).book 23 ページ ２００６年２月６日 月曜日 午前１０時５２分 Searching for recorded video C Date/time search 1 Press the SEARCH button during recording or live video. 2 Turn the J-dial, select "TIME/DATE SEARCH", and turn the S-dial clockwise. The cursor moves to "CHANNEL". The cursor moves to "PREVIEW". 26-10-06 (J) ☞ Press the SEARCH button to cancel the search mode. Operation returns to the normal screen.
L8HBM_XE(HARD)(GB).book 24 ページ ２００６年２月６日 月曜日 午前１０時５２分 Searching for recorded video E Motion detection search Plays back video stored in the archive area. 1 Press the SEARCH button during recording or live video. 2 Turn the J-dial, select "ARCHIVE AREA SEARCH", and turn the S-dial clockwise. The screen is displayed. The eight most recent archive recordings are displayed in the order of archiving. ☞ Press the SEARCH button to cancel the search mode.
L8HBM_XE(HARD)(GB).book 25 ページ ２００６年２月６日 月曜日 午前１０時５２分 Searching for recorded video E Motion detection search (continued) 1 Press the SEARCH button during recording or live video. 2 Turn the J-dial, select "MOTION DETECTION SEARCH", and turn the S-dial clockwise. The screen appears. The "SEARCHING" starts blinking. ☞ Press the SEARCH button to cancel the search mode. Operation returns to the normal screen.
L8HBM_XE(HARD)(GB).
L8HBM_XE(HARD)(GB).book 27 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media Selected video stored in the normal recording area and the alarm recording area can be copied to various media (full screen). Images copied to a CompactFlash card can be directly printed on a printer.
L8HBM_XE(HARD)(GB).book 28 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media A Copying video (example: 10 seconds) from the normal or alarm recording area to the archive area 1 Start playback from the normal or alarm recording area. 2 Press the STILL button at the image to be copied. The image is paused. 7 Turn the J-dial to select "SECONDS", and then turn the S-dial clockwise. The cursor moves to "COPY START". HOW MANY : 10 SECONDS STILL COPY CH Press the COPY button.
L8HBM_XE(HARD)(GB).book 29 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media B Copying video (example: 10 seconds) from the internal hard disk to the CD-R/RW drive 1 Connect the optional CD-R/RW drive to the USB connector on the front or rear panel of the DVR. If the front and the rear USB terminal are connected simultaneously the front is given priority. 2 Start playback from the normal, alarm or the archive area. 3 Press the STILL button at the image to be copied. The image is paused.
L8HBM_XE(HARD)(GB).book 30 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media C Copying video (example: 10 pictures) from the internal hard disk to media such as a CompactFlash card Copy to a Microdrive is also possible, up to 2GB. 1 Insert the card into the CompactFlash card slot. Refer to the names and functions of parts when inserting the card. (P9) 2 Start playback from the normal, alarm or the archive area. 3 Press the STILL button at the image to be copied. The image is paused.
L8HBM_XE(HARD)(GB).book 31 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media D Printing images directly from the CompactFlash card or the Microdrive 1 Insert the card into the CompactFlash card slot. Refer to the names and functions of parts when inserting the card. (P9) 2 Start playback from the normal, alarm or the archive area. 3 Press the STILL button at the image to be printed. The image is paused.
L8HBM_XE(HARD)(GB).book 32 ページ ２００６年２月６日 月曜日 午前１０時５２分 Copying recorded video to media CompactFlash cards or CD-RW formats b CompactFlash format • If no CD-R/RW driver is connected to the USB terminal, the format of the CompactFlash is given priority. • The Microdrive can be formatted in the same way. 1 Insert the CompactFlash card in the CompactFlash card slot. (P9) 2 Press the PLAY/STOP button, the STILL button, and the COPY button. The COPY TO screen is displayed.
L8HBM_XE(HARD)(GB).book 33 ページ ２００６年２月６日 月曜日 午前１０時５２分 Main menu configuration The main menu consists of seven items, and can be displayed by pressing the MENU button. b Initial settings (P34) 1.LANGUAGE/CLOCK SET 2.CAMERA DETECT 3.TITLE SET 4.HOLIDAY SET 5.TIME PERIOD SET 1.INITIAL SET 2.RECORD SET 3.GENERAL SET 4.SCREEN SET 5.POWER LOSS/USED TIME 6.INITIALIZATION LOG 7.
L8HBM_XE(HARD)(GB).book 34 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initial settings Menu configuration b Displaying the initial settings screen 1 Press the MENU button. The screen is displayed. MENU 1.INITIAL SET 2.RECORD SET 3.GENERAL SET 4.SCREEN SET 2 -> -> -> -> Turn the S-dial clockwise, turn the J-dial to select the submenu and then turn the S-dial clockwise The screen is displayed. The selected screen (A~E) is displayed.
L8HBM_XE(HARD)(GB).book 35 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initial settings A Summer time setting A-1 External clock setting Automatic switching from standard time to summer time can be set. 1 Display the screen as explained in "Displaying the initial settings screen" (P34). Connect the CLOCK OUT terminal of the CONTROL terminal block on the rear panel of the DVR to the CLOCK IN terminal of the second DVR (P34: Figure 1), and move the cursor to .
L8HBM_XE(HARD)(GB).book 36 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initial settings C Title setting D Holiday setting Titles for each camera can be up to 10 characters. ☞ Setting conditions 1 Set the start and end time for Sunday (SUN) using the , and then switch the "SET" to "ON". (P51) Display the screen as explained in "Displaying the initial settings screen" (P34). The monitor shows live video, and the <title set> screen is displayed. WEEK SUN MON TUE <main menu> 1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-38.html>PAGE 38</a></h6><p>L8HBM_XE(HARD)(GB).book 37 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initial settings E Time period setting The time period setting allows for using different settings, such as automatic scrolling, masking, motion sensor detection settings for four periods of the day (for example: early morning, morning, daytime and evening). There are two timers (A and B) that can be set to control time periods as shown below, allowing for a wide variety of settings to suit every surveillance need.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-39.html>PAGE 39</a></h6><p>L8HBM_XE(HARD)(GB).book 38 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initial settings E Time period setting (continued) Set automatic scrolling, masking or motion sensor for the time periods (A/B). The default setting for "SELECT TIME PERIOD" is A for all items. When the specified time comes, these operations will work in time period A, but more detailed settings are necessary.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-40.html>PAGE 40</a></h6><p>L8HBM_XE(HARD)(GB).book 39 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings Menu configuration b Displaying the recording settings screen 1 A Easy recording settings (P40) <normal rec easy set> Press the MENU button and use the J-dial to select "2. RECORD SET", and then turn the S-dial clockwise. The <record set> screen appears. RECORDING DURATION BASE -> REC RATE BASE -> CAUTION ! CONNECT CAMERA AND SET TIME BEFORE SETUP The recording duration or rate can be selected.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-41.html>PAGE 41</a></h6><p>L8HBM_XE(HARD)(GB).book 40 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings A Easy recording menu description The following two easy settings are available.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-42.html>PAGE 42</a></h6><p>L8HBM_XE(HARD)(GB).book 41 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings A-1 RECORDING DURATION BASE 4 Setting the recording based on duration 1 Display the <normal rec easy set> screen as explained in "Displaying the recording settings screen" (P39). The <normal rec easy set> screen appears. <main menu> 2.RECORD SET MENU Set the timer. Proceed to 5 if timer setting is not necessary. 1 Turn the S-dial clockwise. The "OFF" starts blinking.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-43.html>PAGE 43</a></h6><p>L8HBM_XE(HARD)(GB).book 42 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings A-2 REC RATE BASE 4 Set the recording based on recording rate Display the <normal rec easy set> screen as explained in "Displaying the recording settings screen" (P39). The <normal rec easy set> screen appears. <main menu> 2.RECORD SET MENU <record set> 1.NORMAL REC EASY SET (J) 2 3 START 09:30 STOP 18:30 "00" of the start time starts blinking. <normal rec easy set> (S) STOP --:-- 3 Turn the S-dial clockwise.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-44.html>PAGE 44</a></h6><p>L8HBM_XE(HARD)(GB).book 43 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings B Recording area menu description This screen is used to verify the total capacity of the hard disk, and the recording capacity of the individual recording areas. The recording areas can be modified as needed. Modifying the recording areas will result in initializing the hard disk, and all recordings to be erased. Save necessary images to some other media before modifying the recording areas.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-45.html>PAGE 45</a></h6><p>L8HBM_XE(HARD)(GB).book 44 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings B-1 Changing the normal recording area and the alarm recording area This operation will initialize the hard disk. 1 Display the <recording area set> screen as explained in "Displaying the recording settings screen" (P39). 5 Turn the S-dial clockwise. The <warning> screen is displayed, and "NO" is blinking. 6 Turn the J-dial, select "YES", and turn the S-dial clockwise.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-46.html>PAGE 46</a></h6><p>L8HBM_XE(HARD)(GB).book 45 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings B-2 Archive area full reset The archive area cannot be automatically overwritten. Performing "AREA FULL RESET" will erase all images from the archive area. 1 Display the <recording area set> screen as explained in "Displaying the recording settings screen" (P39). <main menu> 2.RECORD SET MENU <record set> 2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-47.html>PAGE 47</a></h6><p>L8HBM_XE(HARD)(GB).book 46 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings C Recording conditions menu description This menu is used to set whether to continue recording and automatically overwrite data, or stop recording without overwriting the data when the normal recording area and the alarm recording area of the hard disk become full.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-48.html>PAGE 48</a></h6><p>L8HBM_XE(HARD)(GB).book 47 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings C-1 1 Overwrite setting for the recording areas Display the <recording conditions set> screen as explained in "Displaying the recording settings screen" (P39). <main menu> 2.RECORD SET MENU C-2 Setting series recording If multiple DVR units are connected, recording can be automatically continued on the next DVR when the recording area of the first one becomes full.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-49.html>PAGE 49</a></h6><p>L8HBM_XE(HARD)(GB).book 48 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings C-2 Setting series recording (continued) C-3 Series recording 2 1 Start recording on the first DVR. • Press the REC/STOP button if using normal recording or normal recording combined with alarm recording. • Press the TIMER button if using timer-controlled recording or timer-controlled recording combined with alarm recording.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-50.html>PAGE 50</a></h6><p>L8HBM_XE(HARD)(GB).book 49 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings Normal recording area menu description D This menu is used to set the picture quality, audio recording and recording rate for the normal recording area. A program number can be selected at the programmed recording settings to use the recording rate set for that program. (P50) D-1 Normal recording area settings 1 <record set> 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-51.html>PAGE 51</a></h6><p>L8HBM_XE(HARD)(GB).book 50 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings E Programmed recording menu description E-1 Programmed recording settings This menu is used to set the desired cameras for each group (P-1, P-2, P-3 and P-4) for programmed recording. For each group, cameras are selected to enable or disable recording from them, and their individual recording rates are also set here.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-52.html>PAGE 52</a></h6><p>L8HBM_XE(HARD)(GB).book 51 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings F Timer setting menu description This menu is used to set the start and end times for timer-controlled recording. The following timer functions are available: F-1 Day of the week timer-controlled recording (same 1 2 3 4 5 6 time and same recording rate every week for the specified day) (P52) <timer set> Sets the timer-controlled recording for the specific day of WEEK START STOP PROGRAM FPS SET SUN --:-- --:-OFF 12.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-53.html>PAGE 53</a></h6><p>L8HBM_XE(HARD)(GB).book 52 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings 1 Day of the week timer-controlled recording (same time, same recording rate every week for the specified day) Display the <timer set> screen as explained in "Displaying the recording settings screen", and then turn the S-dial clockwise. (P39) The "SUN" field starts blinking. 4 TIMER <main menu> 2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-54.html>PAGE 54</a></h6><p>L8HBM_XE(HARD)(GB).book 53 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings F-2 Overlapping timer-controlled recording 1 Display the <timer set> screen as explained in "Displaying the recording settings screen". (P39) 3 Press the EXIT/OSD button. 4 Press the TIMER button. The TIMER indicator turns on, and the timer-controlled recording goes into standby mode. EXIT/OSD <main menu> 2.RECORD SET MENU <record set> 6.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-55.html>PAGE 55</a></h6><p>L8HBM_XE(HARD)(GB).book 54 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings F-3 External timer-controlled (alarm) recording 1 Connect an external timer device to the EXT TIMER IN terminal on the rear panel (Figure 1). 2 Display the <timer set> screen as explained in "Displaying the recording settings screen". (P39) b Setting a program for timer-controlled recording Perform the following settings to set a program after setting the timer-controlled recording. Example: EXT ***** ***** <main menu> 2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-56.html>PAGE 56</a></h6><p>L8HBM_XE(HARD)(GB).book 55 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings G Alarm recording settings menu description The following settings can be performed under the alarm recording settings. G-1 Alarm recording (P56) 1 2 3 4 5 7 8 F G H <alarm rec mode set> ALARM RECORDING : OFF PICTURE QUALITY : ENHANCED AUDIO RECORDING : OFF ALARM INTERLEAVE : ONLY REC RATE: 12.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-57.html>PAGE 57</a></h6><p>L8HBM_XE(HARD)(GB).book 56 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings G-1 Alarm recording settings 4 Turn the J-dial to select the recording pattern Display the <alarm rec mode set> screen as explained in "Displaying the recording settings screen", and then turn the S-dial clockwise. (P39) The "OFF" field of ALARM RECORDING starts blinking. MENU (J) (ALARM INTERLEAVE), and then turn the S-dial twice clockwise. Selections: ONLY/SW If ONLY is selected (Figure 1): <main menu> 2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-58.html>PAGE 58</a></h6><p>L8HBM_XE(HARD)(GB).book 57 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings G-2 Pre-alarm recording settings 1 6 Turn the J-dial to select the REC RATE (example: Display the <alarm rec mode set> screen as explained in "Displaying the recording settings screen", and then turn the S-dial clockwise. (P39) The "OFF" field of ALARM RECORDING starts blinking. 8.333), and then turn the S-dial clockwise. Repeat the same procedure to set the DURATION (example: 20SEC).</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-59.html>PAGE 59</a></h6><p>L8HBM_XE(HARD)(GB).book 58 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings G-4 Motion sensor screen description Use this screen for motion sensor setting on a live video screen to detect moving objects such as intruders, and generate alarms. The motion sensor detects movement based on intensity-changes on the screen. It is necessary to use sensor settings that are appropriate for both the location of the sensor and for the observed objects.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-60.html>PAGE 60</a></h6><p>L8HBM_XE(HARD)(GB).book 59 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings G-5 Motion sensor setting 1 Set "TIME PERIOD A" and "TIME PERIOD B" using <time period set> (P37). 2 Display the <alarm rec mode set> screen as explained in "Displaying the recording settings screen", and then turn the S-dial clockwise. (P39) The "OFF" field of ALARM RECORDING starts blinking. 3 Turn the J-dial, set the sensor to "A", and turn the S-dial clockwise.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-61.html>PAGE 61</a></h6><p>L8HBM_XE(HARD)(GB).book 60 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings H Alarm operation settings menu description This menu is used to extend the duration of the alarm recording and to set the display method when an alarm occurs. <alarm operation set> ALARM RETRIGGER : OFF 1 2 3 4 MAIN MON. DISPLAY ALARM PRIORITY MON.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-62.html>PAGE 62</a></h6><p>L8HBM_XE(HARD)(GB).book 61 ページ ２００６年２月６日 月曜日 午前１０時５２分 Recording settings H-1 Alarm operation settings H-2 Alarm display settings 1 1 Display the <alarm operation set> screen as explained in "Displaying the recording settings screen", and then turn the S-dial clockwise. (P39) The "OFF" indicator of ALARM RETRIGGER starts blinking. Turn the J-dial, select "MAIN MON. DISPLAY", and turn the S-dial clockwise. The "FULL" indicator of MAIN MON. DISPLAY starts blinking.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-63.html>PAGE 63</a></h6><p>L8HBM_XE(HARD)(GB).book 62 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings Menu configuration b Displaying the general settings screen MENU <main menu> 1.INITIAL SET 2.RECORD SET 3.GENERAL SET 4.SCREEN SET Turn the J-dial, select the desired submenu, and turn the S-dial clockwise. The selected screen (A~G) is displayed. Refer to the appropriate pages for the settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-64.html>PAGE 64</a></h6><p>L8HBM_XE(HARD)(GB).book 63 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings A Data display settings/VIDEO LOSS settings These settings are used to control the operating display area of the monitor, to display the date, time and other information. Normally all indicators are displayed, but they can be hidden, if needed. "VIDEO LOSS" can be set to be displayed when a camera video is interrupted due to an unexpected problem, or a lamp connected to the rear panel control terminals can be turned on.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-65.html>PAGE 65</a></h6><p>L8HBM_XE(HARD)(GB).book 64 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings B Buzzer settings These settings are used to generate a warning buzzer when the hard disk is full and at alarm events. 1 Display the <buzzer set> screen as explained in "Displaying the general settings screen", and then turn the S-dial clockwise. (P62) The "OFF" field in the ALARM line starts blinking. <main menu> 3.GENERAL SET MENU 3 Press the EXIT/OSD button. EXIT/OSD ☞ Press any operating button to stop the buzzer.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-66.html>PAGE 66</a></h6><p>L8HBM_XE(HARD)(GB).book 65 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings C Security lock menu description This menu is used to set passwords and to limit access to the DVR. There are two passwords, one for the administrator, and one for the user. <security lock set> LEVEL PASSWORD(4-8) USE ADMIN -------- OFF USER -------- OFF REC CONTROL : ADMIN 1 2 3 Turn ON the ADMIN and USER C-1 security locks and set passwords for the DVR Refer to P67 for information on the control rights after setting the passwords.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-67.html>PAGE 67</a></h6><p>L8HBM_XE(HARD)(GB).book 66 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings C-2 Activating the security lock C-3 Cancelling the security lock When the administrator and user settings are complete, activate the security lock. 1 Press the SHUTTLE HOLD button for about 3 seconds while live video is on the screen. The LOCK indicator on the front panel turns on and a buzzer sounds to indicate the activation of the security lock.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-68.html>PAGE 68</a></h6><p>L8HBM_XE(HARD)(GB).book 67 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings b List of permitted operations after setting the passwords <security lock set> LEVEL PASSWORD(4-8) USE ADMIN -------- OFF USER -------- OFF REC CONTROL : ADMIN 1 2 3 If both the ADMIN and USER are "ON": • If the ADMIN password is entered, all operations will be permitted. • If no password is entered, all operations will be denied.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-69.html>PAGE 69</a></h6><p>L8HBM_XE(HARD)(GB).book 68 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings D Hard disk settings menu description D-1 Hard disk initialization 1 1 2 3 4 5 <hdd set> DISK1 : 82GB DISK2 : ---GB DISK INITIALIZE -> CAUTION : ALL RECORDING WILL BE ERASED! Displays the total capacity of the internal hard disk. If the hard disk is replaced, the capacity may change. 2 DISK2 Displays the total capacity of the second hard disk, if it was installed in the DVR. <main menu> 3.GENERAL SET MENU <general set> 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-70.html>PAGE 70</a></h6><p>L8HBM_XE(HARD)(GB).book 69 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings E Network settings E-1 Network password modification 1 Connecting the DVR to the network Refer to the Network connection terminals (LAN). (P11) 2 Display the <network set> screen as explained in "Displaying the general settings screen", and then turn the S-dial clockwise. (P62) The "OFF" field NETWORK CONTROL starts blinking. There are three access levels (ID1, ID2, ID3) to connect to the network.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-71.html>PAGE 71</a></h6><p>L8HBM_XE(HARD)(GB).book 70 ページ ２００６年２月６日 月曜日 午前１０時５２分 General settings F RS-485 settings 1 Connect the RS-485 terminal on the rear panel of the DVR with the system controller (Figure 1). 2 Display the <rs-485 set> screen as explained in "Displaying the general settings screen", and then turn the S-dial clockwise. (P62) The DATA SPEED "19200" indicator starts blinking. Figure 1 (Do not use telephone wires.) System controller (sold separately) <main menu> 3.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-72.html>PAGE 72</a></h6><p>L8HBM_XE(HARD)(GB).book 71 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings Menu configuration b Displaying the screen settings 1 A Changing the multi-screen position (P72) Press the MENU button and use the J-dial to select "4. SCREEN SET", and then turn the S-dial clockwise. The <screen set> screen appears. Screen-position modification for live video and playback. <multi 6 position set menu> <quad position set menu> QUAD1 QUAD2 01 02 05 06 03 04 01 02 02 01 03 04 05 06 MENU <main menu> 1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-73.html>PAGE 73</a></h6><p>L8HBM_XE(HARD)(GB).book 72 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings A Changing the multi-screen position Display the <screen set> screen as explained in "Displaying the screen settings", and then turn the S-dial clockwise. (P71) The "NORMAL" field of 1. MULTI SCREEN starts blinking. 3 <main menu> 4.SCREEN SET MENU <screen set> 1.MULTI SCREEN : NORMAL QUAD POSITION SET -> MULTI 6 POSITION SET -> (S) 2 2.SEQUENCE : 1SEC SEQUENCE SET -> MAIN/MON.2 MONITOR SET -> 3.MASK : OFF MASK SET -> 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-74.html>PAGE 74</a></h6><p>L8HBM_XE(HARD)(GB).book 73 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings Automatic scrolling of live video of the B main monitor and the monitor 2 at identical intervals (example: 5 seconds) 1 Display the <screen set> screen as explained in "Displaying the screen settings" (P71). <main menu> 4.SCREEN SET MENU Automatic scrolling of live video of the B-1 main monitor and the monitor 2 at individual intervals 1 Display the <screen set> screen as explained in "Displaying the screen settings" (P71).</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-75.html>PAGE 75</a></h6><p>L8HBM_XE(HARD)(GB).book 74 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings Automatic sequence of live video of the main monitor (full-screen) at individual B-2 intervals, and of the monitor 2 at identical intervals (example: 3 seconds) 1 Display the <screen set> screen as explained in "Displaying the screen settings" (P71). 2 Turn the J-dial, select "2. SEQUENCE", and then turn the S-dial clockwise. 3 Turn the J-dial to select "INDIV.", and then turn the S-dial twice clockwise.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-76.html>PAGE 76</a></h6><p>L8HBM_XE(HARD)(GB).book 75 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings C Masking specific camera images 1 Set TIME PERIOD A and TIME PERIOD B using <time period set> (P37). Select "TIME PERIOD A" or "TIME PERIOD B" for "MASK" under "SELECT TIME PERIOD". The example uses "TIME PERIOD A". 6 Turn the S-dial, and use the J-dial to select the desired TIME PERIOD (example: T-2), and then turn the S-dial clockwise. The cursor moves to "01" (CH) of the MAIN MON. line.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-77.html>PAGE 77</a></h6><p>L8HBM_XE(HARD)(GB).book 76 ページ ２００６年２月６日 月曜日 午前１０時５２分 Screen settings D Adjusting color tones of the live video 1 Display the <screen set> screen as explained in "Displaying the screen settings" (P71). <main menu> 4.SCREEN SET MENU <screen set> 1.MULTI SCREEN : NORMAL QUAD POSITION SET -> MULTI 6 POSITION SET -> (S) 2 2.SEQUENCE : 1SEC SEQUENCE SET -> MAIN/MON.2 MONITOR SET -> 3.MASK : OFF MASK SET -> 4.COLOR LEVEL SET -> Turn the J-dial, select "4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-78.html>PAGE 78</a></h6><p>L8HBM_XE(HARD)(GB).book 77 ページ ２００６年２月６日 月曜日 午前１０時５２分 Power loss information/Used time Power loss/Used time menu description A <power loss used loss ----- --:------ --:------ --:------ --:-used time disk1 use : disk2 use : power : power #000 1 2 3 time> RECOVER ----- --:------ --:------ --:------ --:-00000H -----H 00000H A-1 Viewing the information Use this procedure to view the power loss dates and times, hard disk running times, and the power-on time of the DVR.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-79.html>PAGE 79</a></h6><p>L8HBM_XE(HARD)(GB).book 78 ページ ２００６年２月６日 月曜日 午前１０時５２分 Initialization log A Initialization log menu description 1 DATE --------------------------------- 2 <initialization log> TIME AREA --:--------:--------:--------:--------:--------:--------:--------:------- 3 A-1 Viewing the log Use this procedure to view the hard disk initialization and area reset log. The log displays the eight most recently performed operations.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-80.html>PAGE 80</a></h6><p>L8HBM_XE(HARD)(GB).book 79 ページ ２００６年２月６日 月曜日 午前１０時５２分 Menu copy A Menu copy screen description A-1 Save the set menu on the CompactFrash (CF) card and load the same menu onto a different DVR of the same model. It is possible to control several units using the same menu. 1 2 3 4 Insert the CF card into the CF card slot Front 2 Insert DVR TYPE VER. SA06-04 SAVE MENUS TO CF 2 Pull out 1 Open <copy menu settings> 1 Save the menu content in the CF card.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-81.html>PAGE 81</a></h6><p>L8HBM_XE(HARD)(GB).book 80 ページ ２００６年２月６日 月曜日 午前１０時５２分 Menu copy A-2 Load menu content saved to the CF card onto other DVRs of the same model. 1 Press the MENU button in order to display the <copy menu settings> screen and load the menu content onto other DVRs of the same model. MENU B) When "YES" is selected for COPY RECORDING AREA SETTINGS (Initialized). <copy menu settings> LOAD MENUS FROM CF -> COPY RECORDING AREA SETTINGS: YES DVR TYPE VER.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-82.html>PAGE 82</a></h6><p>L8HBM_XE(HARD)(GB).book 81 ページ ２００６年２月６日 月曜日 午前１０時５２分 Interface (RS-485) specifications b Data format b Communication protocol Mode Character length Data transmission speed Parity check Stop bit It is recommended that the exclusive controller is used for operation as a protocol unique to our company (SANYO protocol) is used for this DVR. Consult the service center regarding the exclusive controller.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-83.html>PAGE 83</a></h6><p>L8HBM_XE(HARD)(GB).book 82 ページ ２００６年２月６日 月曜日 午前１０時５２分 Specifications Signal method Compression method Number of pixels Recording type Recording quality PAL signal standard Video: M-JPEG, Audio: WAVE 720 x 288 Field record 5 stage [BASIC/NORMAL/ENHANCED/ FINE/SUPER FINE] Recording rate 27 levels (50 to 0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-84.html>PAGE 84</a></h6><p>L8HBM_XE(HARD)(GB).book 83 ページ ２００６年２月６日 月曜日 午前１０時５２分 List of recording rate and recording times The recording time on this DVR are adjusted automatically when the recording rate and the recording quality have been altered. The list below displays the recording rate and quality when recording images within the hard disk normal recording area of this DVR.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-85.html>PAGE 85</a></h6><p>L8HBM_XE(HARD)(GB).book 84 ページ ２００６年２月６日 月曜日 午前１０時５２分 List of recording rate and recording times b When recording using an 500GB hard disk (when 99% of the area is utilized) Recording rate (fields/second) 50 25 16.67 12.5 8.333 6.25 5 4.167 3.571 3.125 2.778 2.5 2.273 1.923 1.667 1.471 1.316 1.190 1.087 1 0.5 0.333 0.25 0.2 0.1 0.05 0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-86.html>PAGE 86</a></h6><p>L8HBM_XE(HARD)(GB).book 85 ページ ２００６年２月６日 月曜日 午前１０時５２分 List of record rate setting/pre-alarm recording times b Recording rate setting Normal recording Pre-alarm recording Program recording Alarm recording (Note 1) (Note 2) (Note 1) 50 F (Note 3) T T T 25 F F F F 16.67 F F F T 12.5 F F F F 8.333 F F F T 6.25 F F F F 5 F F F T 4.167 F F F T 3.571 F F F T 3.125 F F F F 2.778 F F F T 2.5 F F F T 2.273 F F F T 1.923 F F F T 1.667 F F F T 1.563 T T T F 1.471 F F F T 1.316 F F F T 1.190 F F F T 1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-87.html>PAGE 87</a></h6><p>L8HBM_XE(HARD)(GB).book 86 ページ ２００６年２月６日 月曜日 午前１０時５２分 Push-lock terminal specifications Input/output terminals 5V Open grounded input 100kΩ 1kΩ 0V Over 100 ms <sensor alarm out> [Open collector/1kΩ, Low Level active (max. 25 mA)] Input/output circuit 10kΩ Open 1kΩ 0V Motion sensor detection Date adjustment input [Zero voltage contact] (CLOCK IN) Clock adjustment output [Open collector/1kΩ, Low Level active (max. 25 mA)] (CLOCK OUT) Alarm total output [Open collector/Low Level active (max.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/sanyo/dsr-3706pa/user-s-manual-english/page-88.html>PAGE 88</a></h6><p>L8HBM_XE(HARD)(GB).book 1 ページ ２００６年２月６日 月曜日 午前１０時５２分 Printed on recycled paper SANYO Electric Co., Ltd.</p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2025</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script>
googletag.cmd.push(function() { googletag.display('pixel'); });
</script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript>
$.extend({
redirectPost: function(location, args) {
var form = '';
$.each(args, function(key, value) {
form += '<input type="hidden" name="' + key + '" value="' + value + '">';
});
form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>';
$(document.body).append(form);
$("#s1").submit();
}
});
$(document).ready(function(){
$("#query").autocomplete({
minChars: 3,
groupBy: 'type',
paramName: 'q',
dataType: 'json',
serviceUrl: '/autocomplete',
noCache: true,
showNoSuggestionNotice: true,
noSuggestionNotice: 'Zarro results found',
onSelect: function (suggestion) {
$.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))});
}
});
var toc = $('.toc-selector');
if (toc.length) {
var slideParams = { duration: 800, easing: 'linear' };
toc.click(function() {
$(this).toggleClass('open');
var section = $('.toc-content');
var isCollapsed = section.attr('data-collapsed') === 'true';
if (isCollapsed) {
section.slideDown(slideParams)
section.attr('data-collapsed', 'false')
} else {
section.slideUp(slideParams);
section.attr('data-collapsed', 'true')
}
});
}
});
var lastSmall = $(window).width() < 576;
$(window).resize(function() {
var newSmall = $(window).width() < 576;
if (lastSmall != newSmall) {
lastSmall = newSmall;
window.location.href = window.location.href;
}
});
</script></body></html>
