ECD-T1545 LOU/ENT/ENT OPEN SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN S-MODE CAT-DIR 3 RPT 4 SHF 5 DISC 6 DISC MON MUT LOC MODE Fold Down Panel Detachable High Power FM/AM Stereo Receiver Compact Disc Player/MP3 Player/With ESP ISO Mounting with Removable Trim Ring Sirius Function (see separate booklet on Sirius Radio operation) Remote Control CD-R/RW Compatibility (English) OPERATING INSTRUCTIONS…………….
CONTENTS COMPACT DISC CARE ...........................................................................................................3 DIGITAL DISPLAY .....................................................................................................................4 DETACHABLE FRONT PANEL .................................................................................................5 GENERAL OPERATION .....................................................................................................
COMPACT DISC CARE Dirt, dust, scratches and warpage can cause a deterioration in the sound or intermittent skipping some tracks during play. TEXT ReWritable • This unit has been designed to play compact discs bearing the identification logo shown on the left. No other discs can be played. • Do not use non-conventional discs such as heart- shaped, octagonal discs, etc. The player could be damaged.
DIGITAL DISPLAY CD-IN indicator Radio Frequency, Time, CD Track Number, Audio Control Selected Mode Stereo Local SAT Channel name indicator Category CLASSIC Mono SAT Skip POP Artist Channel name Loud ROCK Subwoofer Song title 4
DETACHABLE FRONT PANEL The front panel is designed to be removable for antitheft purposes. It is recommended that you remove and carry the front panel with you when you leave your car. HOW TO DETACH THE FRONT PANEL Press the release button (OPEN) to fold down the front panel. To remove the front panel, lift it up at a little angle from horizontal position, then first pull out the right side and then pull out the left side.
GENERAL OPERATION 3 2 6 LOU/ENT/ENT OPEN BAND 50W x 4 VOLUME A-Z/0-9 SEL 8 IR MANU/SKIP/CH EQ ECD-T1545 P.SCN AS/PS DSP MP3 7 1 1 PAU 2 SCN S-MODE CAT-DIR 3 RPT 4 SHF 5 DISC 6 DISC MON MUT 5 LOC MODE 10 SW 4 9 TURNING THE POWER ON........................Any button Install the front panel and press any button (except OPEN button) when ACC is on. TURNING THE POWER OFF ...............................….. (1) When system is on, press the button (1) to turn off the unit.
- e.g. When preset button is pressed. When BAND/LOU/ENT button is pressed. When AS/PS/P.SCAN/MP3 button is pressed. BEEP ALL mode: The beep is generated when every button is pressed. BEEP OFF mode: The beep is disabled. MODE SELECTION...................................……..…....(4) Press MODE/SW button (4) to choose desired listening mode. (e.g. radio mode to SIRIUS mode to CD (MP3) mode to CDC (or AUX) mode) SUBWOOFER FUNCTION...........................…...…....
RADIO OPERATION 2 LOU/ENT/ENT OPEN BAND 50W x 4 VOLUME A-Z/0-9 SEL 3 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN 4 S-MODE CAT-DIR 3 RPT 4 SHF 5 5 DISC 6 DISC MON MUT 7 LOC MODE 6 1 SW SWITCHING TO RADIO MODE…………………….…(1) Press MODE/SW button (1) to select radio mode, the radio mode appears in the display together with the memory band and frequency. SELECTING THE FREQUENCY BAND……………..
LOCAL/DISTANT SELECTION ...........................…..(6) Press LOC/S-MODE button (6) to set local or distant stations. Use local position (LOC appears on the display) for reception of strong station, and distant position (DX appears on the display) for reception of weaker stations. This function is effective during AUTO SEEK operation. MONO/STEREO.......................……………………….(7) Press MON button (7) to select mono or stereo mode.
CD OPERATION 3 LOU/ENT/ENT OPEN SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN 3 RPT 4 SHF 5 6 7 4 S-MODE CAT-DIR 5 DISC 6 DISC MON MUT LOC MODE SW 2 1 8 LOADING AND EJECTING THE CD……………....(1),(8) Press OPEN button to fold down the front panel, then insert a disc into the CD slot (1) and the CD player will start. Press the eject button (8) to eject a disc. SWITCHING TO CD MODE............................…..........
PLACING THE CD IN PAUSE MODE ........................ (4) While playing a CD, press the PAU button (4). To resume playing, press the PAU button (4) again. Notes • During playback of a CD, the CD running indicator spins. • The unit will turn-on automatically when a CD is inserted if the ignition switch is “ON”. SCAN MODE (PLAYING THE BEGINNING OF EACH TRACK) ...................................................... (5) This function plays the first several seconds of each track sequentially.
CD CHANGER OPERATION 2 OPEN LOU/ENT/ENT SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 3 S-MODE CAT-DIR 2 SCN 3 RPT 4 SHF 4 5 6 5 DISC 7 6 DISC MON MUT LOC MODE SW 1 8 SWITCHING TO CD CHANGER (CDC) MODE..........(1) Press the MODE/SW button (1) with the power on to select CDC mode. When the CDC mode is switched on, playback begins with the first CD that the CD changer detects.
SHUFFLE MODE......................................................... (6) This function plays the tracks on one CD or all CDs in the magazine in random order. • “Shuffle-playing” tracks Press the SHF button (6) to play the current disc in random order. • “Shuffle-playing” discs Press and hold the SHF button (6) for several seconds. The system selects a disc at random and plays all tracks on that disc. When all tracks have been played, the next disc is selected and “Shuffle-playing” is repeated.
MP3 OPERATION 15 4 5 LOU/ENT/ENT OPEN BAND 50W x 4 VOLUME A-Z/0-9 SEL 10 IR MANU/SKIP/CH EQ ECD-T1545 P.SCN AS/PS DSP MP3 9 3 1 PAU 11 S-MODE CAT-DIR 2 SCN 3 RPT 4 SHF 5 DISC 12 13 14 7 6 DISC MON MUT LOC MODE SW 2 6 1 8 LOADING AND EJECTING THE MP3-CD……………....(1),(8) Press OPEN button to fold down the front panel, then insert a disc into the disc slot (1) and the player will start. Press the eject button (8) to stop MP3 function and eject the disc from disc slot (1).
SEARCHING TRACK DIRECTLY...................………….…(3),(4),(5) Press the AS/PS/MP3 button (3) one time to enter into “Searching track directly” mode. Set desired track by rotating VOLUME A-Z/0-9 dial (4), and then press BAND/LOU/ENT button (5) shortly. Note: The unit searches the track after few seconds, even if the BAND/LOU/ENT button (5) is not pressed. SEARCHING DIRECTORY OR FILE NAME.......…...(3),(4),(5),(15) Press the AS/PS/MP3 button (3) two times.
REPEAT THE SAME SONG...............……………….(13) Press RPT button (13) to continuously repeat the same song. Press again to cancel repeat function. SCAN...............………………………………………….(12) The scan function enables you to listen to the first few seconds of the song. Press SCN button (12) to activate/deactivate scan function. PLAY SONGS IN RANDOM ORDER.........………….(14) During MP3 operation, press SHF button (14) to play songs in random order. Press again to cancel the function. DISPLAY INFORMATION.........
MIXED-CD OPERATION LOU/ENT/ENT OPEN SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN S-MODE CAT-DIR 3 RPT 4 SHF 5 DISC 1 6 DISC MON MUT LOC MODE SW 2 This unit can play the mixed-CD disc (the disc contains both CD audio tracks and MP3 files). When you insert a mixed-CD disc into the CD slot, it starts to play the CD audio tracks. And the operation is the same as that of the CD operation described in page 12.
AUX MODE OPERATION LOU/ENT/ENT OPEN SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN S-MODE CAT-DIR 3 RPT 4 SHF 5 DISC 6 DISC MON MUT LOC MODE SW 1 SWITCHING TO AUX MODE.......................................(1) The unit has a pair of auxiliary input terminals (see WIRING figure on page 27). This allows you to listen to an auxiliary audio source (MP3, portable cassette player, etc).
ERROR SIGNS If a problem should occur while operating the CD player, one of the following error signs may be displayed. Refer to the table below to identify the problem. DISPLAY DESCRIPTION ERROR 1 MECHANISM ERROR ERROR 2 SERVO ERROR If a problem should occur while operating the CD CHANGER player, one of the following error signs may be displayed. Refer to the table below to identify the problem.
REMOTE CONTROL 3 5 A-Z/0-9 SW SET 2 1 POWER 6 4 VOL 7 MANU/SKIP/CH LOU/ENT/ENT VOL PAST .SCN/MP3 8 9 PAU 10 17 SHF SCN 11 14 S-MODE RPT DISC/CAT/DIR 12 13 15 16 1.POWER 10.PAU 2. SEL/SET 3. VOL (A~Z/0~9) 4. VOL (A~Z/0~9) 5. MOD/SW 6. MANU/SKIP/CH 7. MANU/SKIP/CH 8. AS/PS/P.CAN/MP3 9. BAND/LOU/ENT/ENT 11.SCN 12.RPT 13.SHF 14.LOC/S-MODE 15. DISC/CAT/DIR 16.DISC/CAT/DIR 17.1~6 Preset buttons REMOTE SENSOR……........…………………..….…..
HINTS FOR PROPER AND SAFE OPERATION • Condensation Moisture can condense on the optical lens of the CD player during humid or rainy days, or after the car heater is turned on. If this occurs the disc player may not function properly. To remedy the situation, remove the disc from the unit and wait approximately one hour. This should allow the moisture to evaporate and restore normal operation. • Temperature Consideration The unit may not operate correctly in extremely hot or cold temperatures.
TROUBLE SHOOTING Sometimes a simple operational error or a mistake in the wiring can appear to be a problem with the unit. Before having the unit serviced, refer to the troubleshooting chart below. Symptom Cause Solution The compact disc The volume control is turned down. Turn up the volume control. does not play when inserted into unit. the The power connections are not wired Check the +12V and ground correctly. connections. No power. The vehicle ignition is switched off.
ACCESSORIES AND HARDWARE INSTALLATION Mounting Bracket (Half Sleeve) X1 Mounting Strap and Screw X4 Removable Trim Ring X1 Unlock Levers X2 Locking Screw X1 Carrying Case X1 INSTALLATION 1. BEFORE INSTALLATION When mounting the unit in a car, keep the unit as level as possible. If the unit must be mounted at an angle, due to the design of the vehicle, make sure the unit does not tilt by more than 300.
2. INSTALLATION PROCEDURES When mounting the unit into a DIN–standard cutout (182x53 mm) in the dashboard or console, attach the provided Removable Trim Ring to the unit. 1. Insert the mounting bracket into the DIN-standard cutout (182x53 mm) in the dashboard or console. 2. Bend the mounting bracket stopper outward until the bracket fits snugly in the cutout. 3. Attaching the Mounting Strap to the underside of the dashboard, using screw.
ELECTRICAL CONNECTIONS WIRING (BLACK) RED WHITE Rch Lch AUX IN CABLE (BLACK) CD CHANGER AND SIRIUS RECEIVER CONNECTOR SOCKET ANTENNA SOCKET (Brown) Lch White FRONT LINE OUT CABLE (Gray) (BLACK) Rch Red (Gray) Lch White REAR LINE OUT CABLE (Green) SUBWOOFER CABLE I.
4. Ground Wire (Black) • Connect this wire to the vehicle chassis. 5. Power Antenna/Amplifier Turn On (Blue/Red) • Connect this wire to the control terminal of a Power Antenna or an external amplifier. • When not using a Power Antenna or an external amplifier, this wire is not connected. 6. I.R Remote Sensor Socket • Connect a remote IR sensor to I.R remote sensor socket to use with the corresponding remote control and to extend range of remote control. MAIN UNIT (BLACK) REMOTE IR SENSOR (OPTIONAL) I.
LINE OUT CONNECTIONS • The unit has two pairs of line out terminals (see WIRING figure above). You can use a separate front or a separate rear channel amplifier to upgrade your system. RCA Line- out Jacks • Connect a patch cable (not supplied) from the White (left channel) and Red (right channel) RCA line output jacks to the line input terminals of the external amplifier. AUXILIARY INPUT CONNECTIONS The unit has a pair of auxiliary input terminals.
SANYO MOBILE AUDIO MODEL ECD-T1545 LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
ECD-T1545 SIRIUS SATELLITE RADIO OPERATING MANUAL LOU/ENT/ENT OPEN SEL BAND 50W x 4 VOLUME A-Z/0-9 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN S-MODE CAT-DIR 3 RPT 4 SHF 5 DISC 6 DISC MON MUT Fold Down Panel Detachable High Power FM/AM Stereo Receiver Compact Disc Player/MP3 Player/With ESP ISO Mounting with Removable Trim Ring Sirius Function Remote Control CD-R/RW Compatibility (English) SIRIUS OPERATION…………….
SIRIUS OPERATION 2 LOU/ENT/ENT OPEN BAND 50W x 4 VOLUME A-Z/0-9 SEL 3 IR MANU/SKIP/CH EQ ECD-T1545 DSP P.SCN AS/PS MP3 1 PAU 2 SCN 4 S-MODE CAT-DIR 3 RPT 4 SHF 8 5 DISC 6 DISC 6 7 MON MUT LOC MODE 5 1 SW SWITCHING TO SIRIUS MODE……………………..…(1) Press MODE button (1) to select Sirius mode. SELECTING USER-PRESET CHANNEL……………..
SIRIUS MODE SELECTION .........….............…….…..(5) Press LOC/S-MODE button (5) to switch Category mode, Skip mode or normal. It is used as the selection of each: Normal Category mode Direct Tune Skip Channel mode When Category mode or Skip mode is engaged, the “CATEGORY” or “SKIP” function is turned on in the display. When Category mode or Skip mode is released, the “CATEGORY” or “SKIP” function is turned off. When Direct mode is engaged, “DIRECT” of alphanumeric display is turned on.
21605 Plummer Street Chatsworth, CA91311 ECD-T1545. Issue Number 1.
