Soundbar Owner's Manual ES Manual del Propietario FWSB405FS To obtain a more detailed Electronic Copy of this Manual or much further contents, go to ES Para obtener una Copia Electrónica más detallada de este Manual o mucho otras contenido, visite sanyo-av.com Need help? sanyo-av.cc o m sanyo-av.
PRECAUTIONS Supplied Accessories • SETUP MANUAL • Remote Control (NC300UH) • Line-in cable Contents PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS ............................................ 3 Your Soundbar Main unit ............................................................................................ 6 Front panel of main unit. ..........................................................6 Back connectors of main unit. .................................................6 Connections .......................
The model and serial numbers of this unit may be found on the cabinet. Model No.: You should record and retain those numbers for future reference. Serial No.: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
Disconnect the mains(AC) plug to shut off when find trouble or not in use. The mains(AC) plug shall remain readily operable. CAUTION: WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries (Battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it.
TRADEMARK INFORMATION The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Funai Electric Co., Ltd. is under license. Other trademarks and trade names are those of their respective owners. MAINTENANCE Servicing • Please refer to relevant topics on the “Troubleshooting Guide” on page 14. If you cannot find any solution there, our service center is pleased to assist you.
Your Soundbar Main unit Front panel of main unit 1 2 1 POWER ( Standby indicator ) Lights up when Soundbar is on standby (Turned Off). Blinks when Soundbar is Turned On and audio output is Muted. 2 Source indicators AUX INPUT : Lights up when you switch to analog input source. LINE INPUT : Lights up when you switch to line in source(3.5mm jack). OPTICAL INPUT : Lights up when you switch to optical input source. Blinks when unsupported optical signals are input.
Connections 1 Connect to a device Connect to TV If your TV does not have audio outputs shown left, to connect the Soundbar directly to your other devices (Blu-ray player, game system, etc.) see your device’s user manual. Use a Coaxial (RCA) to Optical Toslink Digital Audio Converter (not supplied) for our Soundbar which only has an optical input.
2 Plug the AC plug into an electrical outlet 3 Turn Soundbar on For Bluetooth connections, refer to “Play audio through bluetooth”. 4 Select the source Lights up when you switch to your connected source.
WALL MOUNT THE SOUNDBAR(OPTIONAL) 1 3.5~4mm/0.14’’ ~0.16’’ 4mm/0.16’’ >25mm/0.98’’ 190m m/7 .5’’ 2 ~5mm /0.2’’ ~9m m/0 .
About the Remote Control Remote Control Button Specification Press to Turn On the unit, or to switch the unit into Standby mode. (To completely Turn Off the unit, you must unplug the AC power cord.) Press to adjust volume up / down for Soundbar. Press to mute the sound and recover the sound. Press to adjust lower-pitched sounds. Press to adjust higher-pitched sounds. Press to select AUX of connected devices to this Soundbar. Press to select Line of connected devices to this Soundbar.
Use your Soundbar Adjust the volume Adjusting the volume (default: level 10) 1) To increase or decrease volume, press VOL +/- on remote control. • To mute sound, press on remote control. – When the mute on, the POWER indicator on the front panel of main unit blinks in red. – When the mute off, the POWER indicator stop blink and light off. • To restore the sound, press Volume LED display again or press VOL +/-.
Adjusting TREBLE and BASS level Adjusting the higher-pitched sound level: TREBLE (default: level ± 0) 1) To increase or decrease the level, press TREBLE K / L on remote control. Level LED display Behavior -2 Lights up for 3 seconds -1 Flashes 3 times 0 +1 Moves from right to left 3 times (default: level ± 0) +2 +3 Adjusting the lower-pitched sound level: BASS (default: level ± 0) 1) To increase or decrease the level, press BASS K / L on remote control.
Play audio through bluetooth on the remote control to switch the Soundbar to Bluetooth mode. 1) Press 2) Turn On the Bluetooth compatible device. 3) On the Bluetooth device, switch on Bluetooth, search for and select SANYO_FWSB405F (see the user manual of the Bluetooth device on how to enable Bluetooth). • If a Passcode is requested, enter “0000”. • If the Soundbar name does not appear on the Bluetooth compatible device, press on the remote control.
INFORMATION Troubleshooting Guide If the Unit does not perform properly when operated as instructed in this Owner’s Manual, refer to the following. Problem Corrective action No Power – Check if the AC power cord is properly connected. – Unplug the outlet once, and wait for 15-20 seconds and then plug it in again. – – – – No Sound Make sure both the TV or other devices and the Soundbar are Turned On. Confirm the connections to the TV are made properly as shown in Connections.
Español 1 3 Conexiones Para conectar a una TV, consulte “Conexiones” en la página 7 y verifique las terminales de la TV, después conecte su Soundbar a la TV, y conecte el cable de energía CA. Para reproducir audio a través de un dispositivo Bluetooth, consulte “Reproducir audio a través de bluetooth” en la página 12 y conecte el dispositivo Bluetooth a su Soundbar.
LIMITED WARRANTY NINETY (90) DAY LABOR / ONE (1) YEAR PARTS WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
