Specifications HE C-A2000 (GENERAL} Power source Local voltage 50/60 Hz Power consumption 250w Rated time 30 minutes Timer (MANUAL COURSE) Approx. 15 minutes (AUTOMATIC COURSE) Approx. 12 minutes 710 mm[width] x 1,160 mm[depth] x 1,060 mm[height] . . t reclined (with foot rest retracted) Dimensions e 710 widths] x 1,820 mm[depth] x 600 lightweight] * When reclined (with foot rest set horizontally) Weight Approx. 63kg Exterior cloth Artificial leather 100% Massaging Frequency (3 stages) Approx. 16 times/min.
Massage Motors HE CG-A2000 (GENERAL) Vassalage motor 1. Tapping motor Screw bar 3. Elevation motor 1. Tapping motor This motor rotates to move the massage balls upward and downward alternately via the driving belt coupled ta the motor. {The motor revolutions is adjustable in three steps so that the patting frequency can be changed over to approximately 300, 480 and 600 cycles/minute.) 2.
Air Massage HE C-A2000 {GENERAL) e of air massaging component for lower extremities " | Zam Structure Air hoses Ajr pump @@ Foot finger pressure (2) Foot pinching @) Leg finger pressure @) Leg pinching Solenoids 1. The air massage is composed of 14 air bags (photo-1} contained in an air pump, an air tank and solenoids (Photo-3), and foot and leg massaging components and of air hoses {photo-2) connecting among them, all of which are located under the seat. 2.
Operation of Stiffness Detecting Sensor HE C-A2000 (GENERAL} « The body size sensor detects the curve along the body figure to recognize the positions of the shoulders. This enables the users of different body sizes to undergo massaging on their desired points of shoulder with no need for complicated adjustment of shoulder position. « During the measurement of shoulder positions, the "“Body size sensor” LED blinks and goes On as soon as the measurement has been finished.
Replacement Procedure HE C-AZ000 (GENERAL) (1) Removing an arm rest (right) {2) Replacing a main board 1. Recline the seat back down to the limit point 1. Lift up the foot rest and insert a driver or so that iris displaced in a horizontal position. any other tool into a ring for fixing. Photo-1 Photo-3 2. Remove one Holt fixing the arm rest (right) 2. Remove four screws fixing the cover {under around the hinge of the seat back. Photo-1 front) to detach the cover.
Replacement Procedure 5. Detach the code attachment system to remove connectors from the main board, 6. Remove three screws from the board frame B to detach the frame B sideways. * Pull out the cord from the hole of the board frame B to detach the frame B. HE C-A2000 (GENERAL) (4) Replacing an air pump and solenoids 1. Detach the attachment system for individual cords. 2. Disconnect the connectors at solenoid terminals. 3. Disconnect the air hoses from the air pump, air tank, and solenoid.
Replacement Procedure HE C-A2000 (GENERAL) {5) Replacement of power switch section (7) Replacement of remote control section 1. Disconnect connector CN1 connected to 1. Disconnect connector CN11 connected to PRINTED BOAS ASS'Y (MAIN). PRINTED BOAS ASS'Y (MAIN). 2. Unscrew two CASE (SWITCH BOX) set 2. Detach bushing of remote control cord and screws and detach power supply switch remove remote control section. section. Photo-8 3.
Replacement Procedure HE C-AZ2000 {(GENERAL) (8) How to detach COVER (BACK COVER) (10) Replacement of elevating motor section 1. Unscrew four COVER (BACK COVER) set 1. Disconnect elevating motor lead wires (CN404). screws and remove COVER (BACK COVER). 2. Detach BELT (ROLLING). Photo-15 Photo-12 3. Detach PULLEY (SM) from elevating motor shaft, and unscrew four elevating motor set screws. Photo-15 & . Photo-12 {3} Replacement of PRINTED BOAS ASS'Y {WIDOW PULSE) 1.
Replacement Procedure 11) Replacement of tapping motor section . Disconnect connectors of tapping motor. . Detach BELT (AKITA. Photo-17 . Unscrew two motor fixing screw. Photo-17 . Unscrew two STAY A (MOTOR T) set screws and remove tapping motor section. Photo.17 BN 5. Remove PULLEY {(TM) from tapping motor shaft and unscrew three tapping motor set S Crews, Photo.
Replacement Procedure HE C-A2000 (GENERAL) {19 Replacement of PRINTED BOAS ASS'Y (RELAY)PULSE) (15) Replacement of PRINTED BOAS ASS'Y (SHAPE) 1. Disconnect three connectors connected to 1. Disconnect three connectors connected to PRINTED BOAS ASS'Y (RELAY). Photo-21 PRINTED BOAS ASS'Y (SHAPE). Photo-23 2. Unscrew two PRINTED BOAS ASS'Y 2. Unscrew 2 substrate holder set screws and {RELAY) set screws and detach PRINTED remove PRINTED BOAS ASS'Y (SHAPE), BOAS ASS'Y (RELAY). Photo-21 Photo-23 3.
Replacement Procedure HE C-A2000 {GENERAL} (17} Replacement of gear box section 1. Detach massaging belt. Photo-25 9. Detach massaging belt. Photo-27 2. Disconnect three connectors connected to 10, Unscrew one STAY (GEAR CASE L) set PRINTED BOAS ASS'Y {RELAY). Photo-25 screw and remove STAY (GEAR CASE L ). 3. Unscrew two PRINTED BOAS ASS'Y Photo-27 (RELAY} set screws and detach PRINTED BOAS ASS'Y (RELAY). Photo-25 4. Unscrew two STAY (HARNESS) set screw and remove STAY (HARNESS). Photo-25 8 5.
Replacement Procedure HE C-A2000 (GENERAL) (18) Replacing a body size sensor (20} Replacing a massaging unit 1. Disconnect the connectors (CN502) from the 1. Remove four screws fixing the frame on the board {the body size sensor) to detach the cross pipe to detach the frame. cord attachment systems. Photo-31 2. Remove the helical spring for the right arm. Photo-29 Rare (on the cross pipe) 3. Remove the E ring fixing the shaft ;! {the body size sensor} to detach the shaft.
Replacement Procedure (22) Replacing a reclining component 1. Disconnect the connectors for individual reclining motor (paired) lead wires connected to the main board. 2. To remove the pins, detach the E rings fixed at two end points where the individual reclining motors (paired) are disposed. Photo-33 (23) Replacement of transformer 1. Unscrew three fixing screws to remove the transformer caver. Photo-34 Transformer cover i 2. Unscrew fixing screws to remove the transformer.