Multimedia Plasma Monitor MODEL PDP-32H1ENV PDP-32H1AN PDP-32H1EN Owner's Manual
TO THE OWNER Before operating this Plasma Monitor, read this manual thoroughly and operate the Plasma Monitor properly. This Plasma Monitor provides many convenient features and functions. Operating the Plasma Monitor properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
SAFETY INSTRUCTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this Plasma Monitor from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Clean only with dry cloth. Follow all warnings and instructions marked on the Plasma Monitor.
COMPLIANCES European Norm Compatibility / CE This machine is provided with the CE-mark and therewith corresponding to the norms that are valid for its operation at present. Thus the effective guidelines on the electromagnetic compatibility 89/336/EWG and safety regulations according to low voltage guideline 73/23/EWG and 93/68/EWG are guaranteed. Mutual disturbances with other electronic appliances are normally excluded, if those also are in accordance with valid norms.
TABLE OF CONTENTS FEATURES AND DESIGN PREPARATION 6 7 NAME OF EACH PART OF PLASMA MONITOR 7 SETTING-UP PLASMA MONITOR 9 CONNECTING PLASMA MONITOR 11 TERMINALS OF PLASMA MONITOR CONNECTING TO VIDEO EQUIPMENT CONNECTING TO COMPONENT VIDEO EQUIPMENT CONNECTING TO COMPUTER 11 13 14 15 BEFORE OPERATION OPERATION OF REMOTE CONTROL OPERATING ON-SCREEN MENU BASIC OPERATION TURNING ON / OFF PLASMA MONITOR OFF TIMER SELECTING INPUT SOURCE PICTURE IMAGE LEVEL SELECT IMAGE LEVEL ADJUSTMENT WIDE SCREEN OPERATI
FEATURES AND DESIGN This Plasma Monitor is designed with the most advanced technology. The Plasma Monitor utilizes built-in multimedia features, a palette of 16.77 million colors, and Plasma Display Panel technology. ◆ High Definition Plasma Panel ◆ ● D-SUB, RGB input for PC (Up to XGA) ● Component input for DVD ● S-Video / Video for VCR This Plasma Monitor has 852 x 1,024 dots High Definition Plasma Display Panel. This Plasma Display Panel has High brightness and wide viewing angle.
PREPARATION NAME OF EACH PART OF PLASMA MONITOR FRONT PLASMA DISPLAY PANEL FRONT CONTROLS AND INDICATORS MENU BUTTON CURSOR BUTTON FRONT CONTROLS Used to set and adjust the menu data on On-Screen Menu. (P18) Used to select MENU operation. (P18) OK BUTTON Used to execute the selected menu on OnScreen Menu. (P18) MENU OK INPUT CURSOR BUTTON Used to select the menu on On-Screen Menu. (P18) VOLUME VOLUME BUTTONS MAIN ON/OFF SWITCH Used to adjust volume.
PREPARATION NAME OF EACH PART OF PLASMA MONITOR BACK COOLING FANS This Plasma Monitor detects internal temperature and automatically controls operating power of Cooling Fans. TERMINALS AND CONNECTORS (SIDE) (Refer to page 11) SPEAKER OUTPUT TERMINALS (LEFT) TERMINALS AND CONNECTORS (BACK) SPEAKER OUTPUT TERMINALS (RIGHT) (Refer to page 12) POWER CORD CONNECTOR NOTES ON USING PLASMA MONITOR For using this Plasma Monitor, Optional Stand or Mounting Bracket is needed.
PREPARATION SETTING-UP PLASMA MONITOR CONNECTING AC POWER CORD This Plasma Monitor uses nominal input voltages of 100120 V or 200-240 V AC. The Plasma Monitor automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use.
PREPARATION INSTALLATION OF OPTIONAL SPEAKERS AND STAND Please read the each option's instruction manual (or installation manual) for the installation. CAUTION IN INSTALLATION ● Through installation work, handling with more than two people is recommended. ● When holding (moving or lifting) the Plasma Monitor, hold the Monitor's body. Do not handle it by holding the attached accessory parts (the Speakers), otherwise damage could be result. ● Provide space that enough larger than the screen size.
CONNECTING PLASMA MONITOR TERMINALS OF PLASMA MONITOR This Plasma Monitor has INPUT TERMINALS and OUTPUT TERMINALS on its side and back, for connecting computers and video equipment. Refer to the figure on pages 13 to 15 and connect properly. SIDE RS-232C TERMINAL RS-232C WIRED R/C When controlling this Plasma Monitor by computer, connect your computer to this terminal.
CONNECTING PLASMA MONITOR BACK VIDEO1 INPUT JACKS PC INPUT TERMINALS Connect video and audio outputs from video equipment. (Refer to P13.) ● S-VIDEO (Mini DIN 4-type) ● VIDEO (RCA-type) ● AUDIO R and L(MONO) (RCA-type) ✽✽ SEE NOTE BELOW Connect computer outputs to this terminals. (Refer to P15.
CONNECTING PLASMA MONITOR CONNECTING TO VIDEO EQUIPMENT NOTE : Models PDP-32H1ENV and PDP-32H1AN only. Cables used for connection ( Cables are not supplied with this Plasma Monitor.) • 21-PIN Video Cable (BNC x 4) • Video Cable (RCA x 1) • Video Cable (RCA x 3) • S-VIDEO Cable • Audio Cable (RCA x 2) NOTE : When connecting Plasma Monitor, AC Power Cords of both Plasma Monitor and external equipment should be disconnected from AC outlet.
CONNECTING PLASMA MONITOR CONNECTING TO COMPONENT VIDEO EQUIPMENT NOTE : Models PDP-32H1ENV and PDP-32H1AN only. Cables used for connection (Cables are not supplied with this Plasma Monitor.) • Video Cable (RCA x 3) or (BNC x 3) NOTE : • Audio Cable (RCA x 2) When connecting Plasma Monitor, AC Power Cords of both Plasma Monitor and external equipment should be disconnected from AC outlet. Component video output equipment.
CONNECTING PLASMA MONITOR CONNECTING TO COMPUTER Cables used for connection • VGA Cable (HDB 15 pin) • Video Cable (BNC x 5) ✽ • MAC Adapter (in the case of connecting Macintosh computer) ✽ • Audio Cables (RCA x 2) or ( Mini Plug - Mini Plug (R/L)) ✽ ✽Those Cables and Adapter are not supplied with Plasma Monitor.
BEFORE OPERATION OPERATION OF REMOTE CONTROL Remote Control Unit can be used as either Wired or Wireless. WIRED REMOTE JACK COMPONENT BUTTON When using as Wired Remote Control, connect Remote Control Cable to this jack. (P17) Used to select COMPONENT VIDEO input. (P22) POWER ON-OFF BUTTON Used to turn Plasma Monitor on or off. (P20) VIDEO BUTTON Used to select video inputs "AV 1" and "AV 2". (P22) INPUT VIDEO COMPONENT ON-OFF VOLUME BUTTONS Used to adjust volume.
BEFORE OPERATION WIRED REMOTE CONTROL OPERATION When using this Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to R/C JACK with Remote Control Cable (supplied). Batteries installation is required when using as Wired Remote Control Unit. Remote Control Cable (supplied) REMOTE CONTROL BATTERIES INSTALLATION 1 Remove the battery compartment lid. 2 Slide 2 batteries into the compartment. OPEN 3 Replace the compartment lid. OPEN Press the lid downward and slide it.
BEFORE OPERATION OPERATING ON-SCREEN MENU You can control and adjust this Plasma Monitor through ON-SCREEN MENU. Refer to the following pages to operate each adjustment on ON-SCREEN MENU. BUTTONS OF ON-SCREEN MENU OPERATION REMOTE CONTROL UNIT WIDE OFF TIMER PICTURE MOVE UP OK CURSOR Used to select the item to adjust. MUTE Used to execute the selected menu. OK CURSOR STATUS Used to set or adjust the menu data. MOVE DOWN MENU MENU POWER ON STATUS Used to display ON-SCREEN MENU.
BEFORE OPERATION MENU LIST Contrast Brightness Color Tint Sharpness Sound Screen adjust PC mode adjustment Setup menu Information : Select OK : OK MENU : Return STATUS : Exit Contrast 63 : Select : Adjust MENU : Return STATUS : Exit Contrast (P24) Brightness 31 : Select : Adjust MENU : Return STATUS : Exit Brightness (P24) Color 31 : Select : Adjust MENU : Return STATUS : Exit Color (P24) Tint 0 : Select : Adjust MENU : Return STATUS : Exit Tint (P24) Sharpness 15 : Select : Adjust MENU : Return
BASIC OPERATION TURNING ON / OFF PLASMA MONITOR 1 Complete the peripheral connections (with Computer, VCR, etc.) before turning on Plasma Monitor. (Refer to "CONNECTING PLASMA MONITOR" on Pages 13~15 for connecting that equipment.) 2 Connect the Plasma Monitor's AC Power Cord into an AC outlet . 3 Press MAIN ON/OFF switch on Front Control of Plasma Monitor to turn ON. POWER indicator will light up(green) when Plasma Monitor is ON. Press MAIN ON/OFF switch again to turn OFF.
BASIC OPERATION WHEN USE MULTIPLE MONITORS When you use multiple Plasma Monitors, you can use POWER ON button and POWER OFF button on Remote Control Unit instead of the POWER ON-OFF button. OK STATUS MOVE DOWN MENU POWER Press POWER ON button to turn Plasma Monitor ON so as not to affect another Plasma Monitor which may be already turned ON.
BASIC OPERATION SELECTING INPUT SOURCE VIDEO INPUT AV 1 Select either "AV 1 (VIDEO 1)" or "AV 2 (VIDEO 2)" by pressing VIDEO button on Remote Control Unit. (Refer to "CONNECTING TO VIDEO EQUIPMENT" on Page 13.) AV 2 COMPONENT INPUT COMPONENT Select "COMPONENT" by pressing COMPONENT button on Remote Control Unit. (Refer to "CONNECTING TO COMPONENT VIDEO EQUIPMENT" on Page 14.) PC PC/RGB INPUT Select "PC" or "RGB 1" by pressing PC/RGB button on Remote Control Unit.
BASIC OPERATION PICTURE IMAGE LEVEL SELECT IN VIDEO/COMPONENT MODE Select image level among Dynamic, Natural, Cinema and Memory by pressing PICTURE button on the Remote Control Unit. Dynamic Dynamic High contrast picture level preset on this Plasma Monitor. Natural Natural Normal picture level preset on this Plasma Monitor. Cinema Cinema Picture level adjusted for the picture with fine tone. Memory Memory User preset picture adjustment in IMAGE ADJUST Menu (P24).
BASIC OPERATION IMAGE LEVEL ADJUSTMENT Press MENU button and ON-SCREEN MENU will appear. 1 2 Press button to select the item that you want to adjust, and then press OK button. The level of selected item is displayed. 3 Adjust each level by pressing button. NOTE : ●Sharpness cannot be adjusted when the input mode is "PC", "RGB 1" or "RGB 2". ●The adjusted Video and Computer matters are memorized individually. Contrast Press button to decrease contrast, and contrast. (From 0 to 63.
BASIC OPERATION WIDE SCREEN OPERATIONS With this function, you can select screen size. WIDE button SELECTING WIDE MODE Natural wide Select screen size among "Natural wide", "Zoom", "Zoom(CaptionIN)", "Full" and "Normal" by pressing WIDE button on the Remote Control Unit. Zoom Zoom(Caption-IN) ✽ "Zoom(Caption-IN)" mode cannot be selected at "PC", "RGB 1" or "RGB 2" input mode.
BASIC OPERATION UP/DOWN PICTURE To move up/down the image vertically, press the MOVE UP / MOVE DOWN buttons. NOTE : ●Up/down picture function can work only when the input signal mode is "AV 1 (VIDEO 1)", "AV 2 (VIDEO 2)" and "COMPONENT". ●Up/down picture function can work only when the image mode is "Natural wide", "Zoom" and "Zoom(Caption-IN)".
BASIC OPERATION SOUND ADJUSTMENT VOLUME Indicates the roughly level of volume. (yellow) Press VOLUME (+/–) button(s) on Remote Control Unit or Front Control to adjust volume. Volume dialog box appears on the screen for a few seconds. (+) button to increase volume, and (–) button decreasing. Volume MUTE 15 (red) Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/–) button(s).
COMPUTER MODE SELECTING INPUT SOURCE REMOTE CONTROL OPERATION PC Select "PC" or "RGB 1" by pressing PC/RGB button on Remote Control Unit. RGB 1 FRONT CONTROL OPERATION RGB 2 Select "PC" or "RGB 1" by pressing INPUT button on Front Control. NOTE : "RGB 2" is used for RGB Video signals from 21-PIN connector. (Refer to "CONNECTING TO VIDEO EQUIPMENT" on page 13.
COMPUTER MODE PC ADJUSTMENT PC MODE ADJUSTMENT "PC mode adjustment" menu is provided to adjust "Auto setup", "Clock", "Phase", "Position", "Power save" and "Information" to conform to your computer. These function can be operated as follows. 1 Press MENU button and ON-SCREEN MENU will appear. 2 Press button to select "PC mode adjustment" menu and then press OK button. "PC mode adjustment" menu will appear. 3 Press button to select the item that you want to adjust, and then press OK button.
COMPUTER MODE Power save Enable or disable Power save function. Enable Power save by choosing "Yes" with buttons. NOTE : ●The Power save function automatically reduces the Plasma Monitor's power consumption if the computer is not operated for a certain period of time. This function can be used when using the Plasma Monitor with a computer conforming to the VESA DPMS standard. ●To activate power save, computer setup is also needed. (Refer to Computer Operation manual.
COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this Plasma Monitor can accept the signal from all computers with the V, H-Frequency mentioned below and less than 100 MHz of Dot Clock.
VIDEO MODE SELECTING INPUT SOURCE VIDEO INPUT AV 1 Select either "AV 1 (VIDEO 1)" or "AV 2 (VIDEO 2)" by pressing VIDEO button on Remote Control Unit. AV 2 COMPONENT INPUT Select "COMPONENT" by pressing COMPONENT button on Remote Control Unit. FRONT CONTROL OPERATION Select "AV 1 (VIDEO 1)" , "AV 2 (VIDEO 2)" or "COMPONENT" by pressing INPUT button on Front Controls.
VIDEO MODE SELECTING VIDEO SYSTEM VIDEO JACK OR S-VIDEO JACK 1 Press MENU button and ON-SCREEN MENU will appear. 2 Press button to select "Setup menu" and then press OK button. "Setup menu" will appear. 3 4 Press button to select "Color system". Press button and select Color system. Auto Plasma Monitor automatically detects incoming Color system, and adjusts itself to optimize its performance.
SETTING SCREEN SAVER FUNCTION Displaying a still picture (non-movement) on the screen for a long time cause a burning image on the screen. To neutralize the remaining image, Screen Saver function (3 modes) is provided in the Monitor. Use the function conveniently. SELECTING SCREEN SAVER "Screen saver" MENU 1 Press MENU button and ON-SCREEN MENU will appear. 2 Press button to select "Setup menu" and then press OK button. "Setup menu" will appear.
SETTING SETTING MENU 1 Press MENU button and ON-SCREEN MENU will appear. 2 Press button to select "Setup menu" and then press OK button. "Setup menu" will appear. 3 Press button to select the item that you want to setup, and setup the selected item by pressing button.
SETTING Color temperature This function is used for selecting color temperature. Select "Normal", "Cool" or "Warm" with buttons which you wish to select. No operation shut off timer This function turns off Plasma Monitor's power automatically, when there is no operation of Remote Control or Front Control for 3 hours.
APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected Plasma Monitor to your equipment as described in the section "CONNECTING PLASMA MONITOR" on pages 13 ~ 15. 2. Check cable connection. Verify that all computer, video and power cords are properly connected. 3. Verify that all power is switched on. 4. If Plasma Monitor still does not produce an image, re-start the computer. 5.
APPENDIX Problem: Try these Solution There are tiny black points and/or bright points on the PDP. ● There may be some tiny black points and/or bright points on PDP (Plasma Display Panel). These points are normal. The POWER indicator is flashing. (No power) ● The Plasma Monitor has trouble, and Self Diagnose function activates. (Refer to P39) WARNING : High voltages are used to operate this Plasma Monitor. Do not attempt to open the cabinet.
APPENDIX INTERNAL TEMPERATURE MONITOR This function activates due to the temperature inside Plasma Monitor. When the temperature inside Plasma Monitor exceeds the normal, after displaying a message, Plasma Monitor will be turned off automatically. When the message "Warning! Internal temperature is too high." is displayed. When this message is displayed, the internal temperature of Plasma monitor exceeds normal. After displaying this message for 10 seconds, Plasma Monitor will be turned off automatically.
APPENDIX TECHNICAL SPECIFICATIONS Screen Diagonal Product name Panel type Display area Resolution / Color Viewing Angle Color System PC Interface Capability Plug & Play Power Management Audio Amp Terminals AC IN VIDEO1 IN ✽ VIDEO2 IN ✽ COMPONENT/RGB IN ✽ PC IN RS232C IN WIRED RC IN MONITOR OUT ✽ HEADPHONE OUT EXT.
APPENDIX MEASUREMENT 829 (32.6) 122 (4.8) 101 (4.0) 829 (32.6) 517 (20.4) Size in mm (inch) OPTIONS The products listed below are optionally supplied. When ordering these products, give name and Type No. to sales dealer. Speaker unit Table top stand Floor stand Side rack Tilt mount unit Wall mount unit Ceiling mount unit KA-SX-32H (R and L) KA-TD-H10S KA-TD-H10W KA-TD-R100 KA-TI-H10 KA-WA-H10WV KA-CH-H10 This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc.
APPENDIX CONFIGURATIONS OF RS232C TERMINALS RS232C TERMINAL Terminal : HDB9-PIN Connect the serial port of computer to this terminal with Serial Cross Cable (not supplied).
APPENDIX CONFIGURATIONS OF PC TERMINALS PC IN (D-SUB) TERMINAL Terminal : HDB15-PIN Connect the display output terminal of computer to this terminal with VGA Cable (supplied). When connecting the Macintosh computer, the MAC Adapter (not supplied) is required. Pin Configuration 4 5 10 15 14 2 3 9 8 12 13 1 7 6 11 1 2 3 4 5 6 7 8 Red Input Green Input Blue Input Sense 2 Ground (Horiz.sync.) Ground (Red) Ground (Green) Ground (Blue) 9 10 11 12 13 14 15 No Connect Ground (Vert.sync.
Printed in Japan Part No. 610 301 2599 (1AA6P1P3504-- J3SF) SANYO Electric Co.
