Multimedia Projector MODEL PLC-XW50A PLC-XW55A PLC-XW55G PLC-XW55K Owner's Manual
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Compact Design This projector is designed compact in size and weight. It is easy to carry and work anywhere you wish to use.
Table of Contents Features and Design . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . 3 To the Owner . . . . . . . . . . . . . . . . . . . 4 Safety Instructions . . . . . . . . . . . . . . 5 Air Circulation 6 Installing the Projector in Proper Position 6 Moving the Projector 6 Compliance . . . . . . . . . . . . . . . . . . . . 7 Part Names and Functions . . . . . . . .
To the Owner Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the projector.
Safety Instructions Air Circulation Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. CAUTION Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Hot air is exhausted from the exhaust vent.
Compliance Federal Communication Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Part Names and Functions Front q Speaker w Focus Ring e Infrared Remote Receiver r Projection Lens t Slide Shutter (See page 52.) y Slide Shutter Lever u Air Intake Vent q wer t y i Exhaust Vents u CAUTION Back i i o !0 !1 u Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side.
Part Names and Functions Rear Terminal q w e r t y u q SERVICE PORT This jack is used to service the projector. w COMPUTER IN /S-VIDEO IN /COMPONENT IN Connect output signal from a computer, RGB scart 21-pin video output, S-VIDEO output, or component video output to this terminal. (p.15-17) y VIDEO IN Connect the composite video output from video equipment to VIDEO jack. (p.16) u AUDIO IN Connect the audio output from video equipment connected to w or y to this jack.
Part Names and Functions Top Control u y t r e w i o q q MENU button Open or close the On-Screen Menu. (p.20) w KEYSTONE ed buttons ✽ Correct the keystone distortion. (p.22, 41) e INPUT button Select input source. (p.25, 34, 35) r POWER ON/STAND-BY button Turn the projector on or off. (p.18, 19) t POWER indicator Emit a red light until the projector gets ready to be turned on. It turns red when the projector is in the stand-by mode. It remains green while the projector is under operation. (p.
Part Names and Functions Remote Control q POWER ON/STAND-BY button Turn the projector on or off. (p.18, 19) e w w VIDEO button q Select VIDEO input source. (p.23, 34) e COMPUTER button Select COMPUTER input source. (p.23, 25, 35) r MENU button Open or close the On-Screen Menu. (p20) t Point ed 7 8 (VOLUME + / –) buttons !5 r t !4 y – Select an item or adjust the value in the OnScreen Menu. (p.20) – Pan the image in Digital zoom + mode. (p.33) – Adjust the volume level.
Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 3 Install new batteries into the compartment. Replace the compartment lid. Two AA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment. To insure safe operation, please observe the following precautions: ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery.
Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set horizontally to the flat screen. ✔ Note: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image. • The values shown below are approximate and may vary from the actual sizes. 32.6' (9.9 m) A:B = 6:1 (Inch Diagonal) 21.7' (6.6 m) 16.3' (5.0 m) 300" 10.8' (3.3 m) 200" 4.3' (1.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station.
Installation Connecting to a Computer Cables used for connection • VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) • Audio Cables (Mini Plug: stereo) ( Not all the cables are supplied with this projector.
Installation Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-Video Cable • S-Video-VGA Cable • Audio Cables (RCA X 2, Mini Plug: stereo) ( Not all the cables are supplied with this projector.
Installation Connecting to Component Video Equipment Cables used for connection • Audio Cables (Mini Plug :stereo) • Scart-VGA Cable • Component Cable • Component-VGA Cable ( Not all the cables are supplied with this projector.
Basic Operation Turning On the Projector 1 2 3 4 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. Connect the projector's AC power cord into an AC outlet. The POWER indicator becomes red. Open the Slide Shutter by sliding the Slide Shutter Lever.(see page 8) Press the POWER ON/STAND-BY button on the top control or on the remote control. The POWER indicator becomes green and the cooling fans start to operate.
Basic Operation Turning Off the Projector 1 Press the POWER ON/STAND-BY button on the top control or on the remote control, and a message "Power off?" appears on the screen. 2 Press the POWER ON/STAND-BY button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling fans are operating for about 120 seconds. (You can select the level of fan quietness and rotation speed. See page 50.
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedures. 1 Press the MENU button to display the On-Screen Menu. 2 Press the Point 7 8 buttons to select a Menu icon to adjust and press the Point ed buttons to select an item to adjust. 3 Press the SELECT button to show the item data. To adjust the data, press the Point 7 8 buttons.
Basic Operation Menu Bar For detailed functions, see Menu Tree on p.58, 59. For computer source Guide Window PC System Menu Show the selected Menu of the On-Screen Menu. Used to select computer Used to select an system. (p.26) image level among Dynamic, Standard, Real, Blackboard (Green), and Image 1 ~ 4. (p.30) Image Select Menu Screen Menu Setting Menu Used to adjust size of image. [Normal / True / Wide / Full screen / Digital zoom +/–] (p.
Basic Operation Zoom Adjustment Press the ZOOM +/- buttons on the top control to adjust the screen size. Screen size can be adjusted 80% to 100% from its maximum screen size. Top Control ZOOM +/- buttons It is not available when On-Screen menu is displayed. Zoom adjustment can be memorized. (p.41) Screen Position Adjustment Screen position can be adjusted in the Zoom Adjustment. 1 Press the ZOOM+ or ZOOM- buttons on the top control.
Basic Operation Sound Adjustment Direct Operation Remote Control Volume VOL+ button Press the VOLUME+/– buttons on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute MUTE button Press the MUTE button on the remote control to cut off the sound. To restore the sound to its previous level, press the MUTE button again or press the VOLUME +/– buttons. Mute function is also effective for AUDIO OUT jack. Approximate level of the volume.
Basic Operation AUTO PC button Remote Control Press the AUTO PC button on the remote control to operate the Auto PC function. For more detail, see page 27. VOLUME +/- buttons (See p.23.) KEYSTONE button (See p.22) D.ZOOM buttons POINT ed buttons Press the D.ZOOM buttons on the remote control to zoom in and zoom out the images. For more detail, see page 33. AUTO PC button IMAGE button NO SHOW button P-TIMER button Press the NO SHOW button on the remote control to black out the image.
Computer Input Input Source Selection Direct Operation Top Control Choose Computer by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. INPUT button INPUT button Computer Video Remote Control COMPUTER button Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is shown on page 61.
Computer Input Auto PC Adjustment Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Direct Operation Remote Control The Auto PC adjustment function can be operated directly by pressing the AUTO PC button on the remote control unit. Menu Operation AUTO PC button PC Adjust Menu Auto PC Adj. 1 Press the MENU button to display the On-Screen Menu.
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu.
Computer Input Display area H Press the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Press the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. The confirmation box appears and then select [Yes]. All adjustments return to their previous figures. Mode free To clear the stored data, select Mode free and press the SELECT button.
Computer Input Image Level Selection Direct Operation Select an image level among Dynamic, Standard, Real, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Dynamic Picture level suitable for viewing picture in a bright room. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics.
Computer Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Computer Input Store To store the adjusted data, select Store and press the SELECT button. Select a level from Image 1 to 4 with the Point ed buttons and press the SELECT button. A confirmation box appears and then select [Yes]. Stored data can be called up by selecting "Image" in the Image Level Selection on page 30. Move the red framed pointer to any of Image 1 to 4 where you want to set and then press the SELECT button. Quit Exit the Image Adjust Menu.
Computer Input For zooming in and out the images Remote Control Digital zoom + POINT buttons When the D.ZOOM + (e) is pressed, the On-Screen Menu disappears and the message "D. zoom +" is displayed. Press the D.ZOOM e or the SELECT button to expand the image size. And press the Point ed 7 8 buttons to pan the image. The Panning function can work only when the image is larger than the screen size. SELECT button D.ZOOM + button D.ZOOM - button Digital zoom – When D.
Video Input Input Source Selection (Video) Direct Operation Top Control INPUT button Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. INPUT button Video Computer Remote Control VIDEO button Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Video Input Input Source Selection (S-Video, Component, RGB Scart 21-pin) Direct Operation Top Control INPUT button Choose Computer by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. INPUT button Computer Video Remote Control COMPUTER button COMPUTER button Computer Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the AV System Menu icon. 2 Press the Point ed buttons to move the red arrow pointer to the system that you want to select and then press the SELECT button. Video or S-Video AV System Menu (Video or S-Video) Auto The projector automatically detects incoming video system, and adjusts itself to optimize its performance.
Video Input Image Level Selection Direct Operation Select an image level among Dynamic, Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Dynamic Picture level suitable for viewing picture in a bright room. Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture with fine tone.
Video Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Video Input Sharpness Press the Point 7 button to soften the image and the Point 8 button to sharpen the image. (From 0 to 15.) Gamma Press the Point 7 8 buttons to adjust the gamma value to obtain better balance of contrast. (From 0 to 15.) Noise reduction Noise interference on the screen can be reduced. Select one of the following to get smoother images. Off . . . . disabled. L1 . . . . lower reduction L2 . . . .
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Screen Menu icon. 2 Press the Point ed buttons and move the red framed pointer to the function that you want to select and then press the SELECT button. Normal Provide the image at a normal video aspect ratio of 4:3.
Setting Setting This projector has Setting menu that allows you to set up the other various functions described as follows: 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Setting Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to set and then press the SELECT button. The Setting dialog box appears.
Setting Display Press the Point 7 8 buttons to switch On/Off. This function decides to display On-Screen Displays. On . . . . . . . . . . . . . Show all the On-Screen Displays. Use this function when you want to project images after the lamp becomes bright enough. Factory default setting is this mode. Countdown off . . . . Show the input image instead of the countdown when turning on the projector.
Setting Capture This function enables you to capture the image being projected and use it for a start-up display or interval of presentations. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image is displayed when turning on the projector next time or pressing the NO SHOW button. (p.24) To capture the image, select [Yes]. To cancel the Capture function, select [No].
Setting To Enter the Logo PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer. The number changes to "✳". If you fixed an incorrect number, move the pointer to the number you want to correct by pressing the Point 7 button, and then select the correct number by pressing the Point ed buttons. Logo PIN code lock Dialog Box After a correct Logo PIN code is entered, the following dialog box appears.
Setting Ceiling Ceiling When this function is "On", the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector. Rear When this function is "On", the picture is left/right reversed. This function is used to project the image to a rear projection screen. Rear Input search This function detects the input signal automatically. When finding a signal, the search will stop. Use the Point 7 8 buttons to select one of the following. Off .
Setting Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. When the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with "No signal" appears. The countdown starts to turn off the lamp. Power management Time left before Lamp is off. Select one of the operations: Ready . . . . . . . .
Setting On start On start When this function is "On", the projector is automatically turned on just by connecting the AC power cord to a wall outlet. ✔ Note: Be sure to turn the projector off properly (see "Turning Off the Projector" on page 19). If the projector is turned off in the incorrect sequence, the On start function does not operate properly. Lamp control This function allows you to change brightness of the screen. Normal . . . . . normal brightness Auto . . . . . . .
Setting Security (Key lock and PIN code lock settings) Key lock This function allows you to use Key lock and PIN code lock function to set the security for the projector operation. Key lock This function locks operation of the top control or the remote control. It is useful to prevent operation by an unauthorized person. ���������� not locked. ���������� lock the operation of the top control. To unlock, use the remote control. ���������� lock the operation of the remote control.
Setting To Enter the PIN code Enter a PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer. The number changes to "✳". If you fixed an incorrect number, move the pointer to the number you want to correct by pressing the Point 7 button, and then select the correct number by pressing the Point ed buttons. Repeat this step to complete entering a four-digit number.
Setting Fan This function provides the following alternatives in the cooling fans' operation after turning off the projector. (p.19) L1 . . . . . . normal operation L2 . . . . . . slower and lower-sound than the normal operation (L1), but it takes longer to cool the projector down. Lamp counter This function is used to reset the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement counter by using this function. See page 55 for operation.
Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. Top Control WARNING blinking red When the temperature inside the projector reaches a certain level, the projector is automatically shut down to protect the inside of the projector.
Maintenance and Cleaning Cleaning the Air Filters Air filters prevent dust from accumulating on the optical elements inside the projector. Should the air filters become clogged with dust particles, it will reduce cooling fans' effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet.
Maintenance and Cleaning Cleaning the Projection Lens Disconnect the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use lens cleaning paper or a commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface. Cleaning the Projector Cabinet Disconnect the AC power cord before cleaning.
Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow, replace the lamp with a new one promptly. TOP CONTROL This indicator is yellow when the life of the projection lamp draws to an end. WARNING: TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover.
Maintenance and Cleaning Lamp Replacement Counter Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting. 1 Turn the projector on, press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Setting Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the Lamp counter function and then press the SELECT button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on pages15-17. – Make sure all equipment is connected to AC outlet and the power is turned on. – When you operate the projector with a computer and it does not project an image, restart the computer. Problem – Solutions No power – Plug the power cord of the projector into the AC outlet.
Appendix No sound – – – – – Some displays are not seen – Check the Display item. (See page 42.) during operations PIN code dialog box appears at the start-up The Remote Control does not work Check audio cable connections from the audio input source. Adjust the audio source. Press the VOLUME + button. (See page 23.) Press the MUTE button. (See page 23.) Is the image projected? You will hear the sound only when the image is projected. – PIN code lock is being set.
Appendix Menu Tree Computer Input/Video Input Input Computer RGB Go to System (1) S-Video Go to System (2) Component Go to System (3) RGB (Scart) N/A Quit ✽ N/A - - - not applicable Video Go to System (2) Volume 0 - 63 Mute On/Off Sound Sound Quit Computer Input System (1) Mode 1 Mode 2 Image Select Dynamic Standard SVGA 1 Real ---- Blackboard (Green) Image 1 ✽ Systems displayed in the System Menu vary depending on the input signal.
Appendix Video Input Setting System (2) Setting Auto Language PAL NTSC NTSC 4.43 PAL-M PAL-N Auto 1080i 1035i 720p 575p 480p Zoom Keystone Blue back Display Logo 575i 480i Image Select Dynamic Standard Cinema Blackboard (Green) Image 1 Image 2 Image 3 Image 4 Image Adjust German French SECAM System (3) English Contrast Brightness 0 - 63 Color 0 - 63 Tint 0 - 63 Color temp.
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators Projector Condition LAMP POWER WARNING REPLACE red red/green yellow The projector is off. (The AC power cord is unplugged.) ✽ The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ✽ The projector is ready to be turned on with the POWER ON/STAND-BY button on the top control or on the remote control.
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited.
Appendix Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Foot Adjustment Multi-media Projector 12.99" x 3.15" x 9.33" (330 mm x 80 mm x 237 mm) (Not including adjustable foot) 6.4 lbs (2.9 kg) 0˚ to 10.0˚ Panel Resolution LCD Panel System 0.
Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. Optional Parts The parts listed below are optionally available.
Appendix Configurations of Terminals COMPUTER IN/S-VIDEO IN/COMPONENT IN/MONITOR OUT TERMINAL (ANALOG) Terminal : Analog RGB (Mini D-sub 15 pin) 4 5 10 15 3 9 14 2 8 13 1 7 12 6 11 1 Red (R/Cr) Input/Output 9 2 Green (G/Y) Input/Output 10 Ground (Vert.sync.) 3 Blue (B/Cb) Input/Output 11 Ground/----- 4 5 Ground (Horiz.sync.
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* * Should the four-digit number be changed, the factory set number will be invalid. While the projector is locked with the PIN code....
KR6AD SANYO Electric Co., Ltd.
