Owner’s Manual HD DATA WIRELESS Transmitter Box Model POA-HDTM01
Features and Design This transmitter POA-HDTM01 can be used on the specified projector with the receiver board POA-MD26HDWL installed. The image from the peripheral equipment is transferred to each projector via wireless network. There is no need for wire connection between the transmitter and the projector. You can select one of 2 installation modes as follows. Single Mode This mode is available only between one transmitter and one receiver.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To the Owner Before operating this transmitter, read this manual thoroughly and operate the transmitter properly. Operating the transmitter properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions Read all of the instructions given here and retain them for later use. Unplug this transmitter from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the transmitter. For added protection to the transmitter during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet.
Safety Instructions Unplug this transmitter from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the transmitter. c. If the transmitter has been exposed to rain or water. d. If the transmitter does not operate normally by following the operating instructions.
Safety Instructions CAUTION IN CARRYING OR TRANSPORTING THE TRANSMITTER AND THE RECEIVER - T he transmitter and the receiver are precision equipment. Do not drop, bump, or subject it to strong forces. Doing so may cause damage or malfunction of the transmitter or the receiver. - When transporting the projector, make sure that the receiver is removed from the projector. Do not transport the projector with the receiver installed. To do so may cause damage or malfunction of the receiver or the projector.
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Compliance The CE Mark is a Directive conformity mark of the European Community (EC). The Alert Mark is a Directive conformity mark of the European Community. Hereby, SANYO FISHER Sales (Europe) GmbH, declares that this Wireless Tx Module (AMN11100) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliance Declaration of Conformity 10
Preparation Before use Package contents The package contains following items. Check each item when unpacking the package. If you have any of the following items missing, contact the sales dealer. ❑ HD DATA WIRELESS Transmitter 1 piece ❑ AC-DC Converter 1 piece ❑ AC Power Cord 1 piece ❑ Owner's Manual 2 pieces 1 piece English ❑ Stand Trademarks and Copyright Each name of corporation or product in this Owner’s Manual is either a registered trademark or a trademark of its respective corporation.
Preparation Part Names and Functions Front q w y u q LINK INDICATOR - When the wireless configuration is set up correctly and the wireless communication is established with the wireless receiver at the single mode, this indicator lights orange. - This indicator lights orange during operation in the broadcast mode. w LCD DISPLAY Display the selected menu. The back light LED will be turned off when the transmitter is not operated for 3 minutes.
Preparation q w r e t q INPUT 1 COMPONENT Connect component output signal (Y-Pb/Cb-Pr/Cr) from video equipment to this terminal. w INPUT 2 DIGITAL (DVI-D) Connect DVI digital output signal from computer to this terminal. e INPUT 3 HDMI Connect HDMI output signal from video equipment to this terminal. This input is only available in the single mode. y r DC 16V Connect the AC adapter (supplied). t SERIAL - This terminal is used to service the transmitter.
Installation Connection to external equipment Cables used for connection q BNC Cable (BNC x 3) Unplug the power cords of both the transmitter and external equipment from the AC outlet before connecting cables. w DVI Cable e HDMI Cable r Serial Control Cable Cables are not supplied with this unit.
Installation Connecting the AC Power Cord This transmitter uses nominal input voltages of 100–120 V or 200–240 V AC. - T he AC outlet must be near this equipment and must be easily accessible. - Use only the supplied AC adaptor, and do not use any other AC adaptor. Otherwise, a malfunction may occur. e Connect the AC adaptor with following steps q to e. When disconnecting, reverse the order. ✔Note: -B e sure to turn off the transmitter, before disconnecting the AC power cord.
Installation Installing the Receiver into the Projector Part Names and Functions Receiver q w q LINK INDICATOR w POWER INDICATOR When the wireless configuration is set up correctly and the wireless communication is established with the transmitter, this indicator lights orange. When this receiver is selected in the projector, this indicator lights green during operation. Replacement of the Receiver Board Insert the HD DATA WIRELESS Receiver board.
Basic Setting and Operation Projector Operation Turning on the Projector 1. C onnect the projector’s AC power cord into an AC outlet and turn on the MAIN ON/OFF Switch. The LAMP indicator lights red and the READY indicator lights green. 2. Press the ON/STAND-BY button on the side control or on the remote control. The LAMP indicator dims red and the cooling fans start to operate. The preparation display appears on the screen and the countdown starts. 3.
Basic Setting and Operation Turning on the Transmitter 1. C omplete peripheral connections before turning on the Hello transmitter. HD Data Wireless 2. C onnect the AC power cord into an AC outlet. (see p.13) The Video 1/5 POWER indicator blinks red and then becomes redSetup in stand-by mode. Wireless 2/5 Setup INPUT SIGNAL >> [S] Phase 1/2 Transmission [OK] NG 3. P ress the ON/STAND-BY button.
Basic Setting and Operation Input Source Selection 1. Choose either INPUT 1 (COMPONENT), INPUT 2 (DVI) or INPUT 3 (HDMI) by pressing the INPUT button. INPUT button INPUT 1 COMPONENT 2. The Indicator of the selected input lights blue. INPUT 2 DVI INPUT indicators INPUT 3 HDMI INPUT button ✐ "INPUT 3 HDMI" cannot be selected in the Broadcast Mode. How to Operate the Menu 1. Press the MENU button to show the LCD Display. Point button 2.
Basic Setting and Operation Menu Tree TRANSMITTER MAIN MENU 1/6 1/6 Single Mode Setup Broadcast Mode Setup 2/6 Image Adjust 3/6 Information SUB MENU 1/2 Authentication Yes/No 2/2 Initialize Yes/No 1/1 Output Level Select 1,2,3,4,5 1/2 Contrast Setting UP/DOWN 2/2 Brightness Setting UP/DOWN Link On / Link Off H freq. / V freq. H resol. / V resol.
Basic Setting and Operation Flow of Installation Mode TRANSMITTER PROJECTOR Single Mode Operation When using a pair of transmitter and receiver for the first time. Step 1: Select "Single mode" in "Mode select". Step 2: Execute "Authentication". Step 2: Select "Execute" in "Authentication". Step 3: "Please wait ..." >>> "Success" Step 3: "Please wait ..." >>> Su ccess icon Step 1: Select "Reset" in "Authentication". Step 2: Execute "Authentication".
Single Mode Operation 6/6: Mode Select & 1/6: Single Mode Setup TRANSMITTER When using a pair of transmitter and receiver for the first time Select the installation mode according to the situation in which the projector is installed. When using in the single mode, it is necessary to perform the mutual authentication between the transmitter and the receiver. Setup them side by side as described below. Main Menu 6/6: Mode Select 1. Press the MENU button to show the Menu.
Single Mode Operation PROJECTOR Mode select 1. P ress the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the HD DATA WIRELESS icon. 2. U se the Point de buttons to move the red frame pointer to the Mode Select icon and then press the SELECT button twice. A dialog box appears. Mode Select Menu 3. U se the Point de buttons to select Single mode and then press the SELECT button. Authentication 1.
Single Mode Operation TRANSMITTER When changing a pair of transmitter and receiver If you want to communicate with the other receiver, you should reset the current authentication. Main Menu 6/6: Mode Select If not set to the Single Mode, set to the Single Mode. Refer to page 22. Authentication SingleMode 1/6 Authenti- 1/2 Setup Main Menu 1/6: Single Mode cation Setup a Sub Menu 2/2: Initialize YES [NO] Authentication [YES] NO 1. Press the MENU button to show the Menu.
Single Mode Operation PROJECTOR Mode select If not set to the Single mode, set to the Single mode. Refer to page 23. Authentication 1. U se the Point de buttons to move the red frame pointer to the Authentication icon and then press the SELECT button. A dialog box appears. Authentication Menu English 2. Select Reset and then press the SELECT button. The authentication will be reset. Authentication Perform the Authentication again. Refer to page 23.
Hello HD Data Wireless INPUT SIGNAL >> [S] 1/5 Phase Broadcast ModeVideo Operation Setup 1/2 INPUT SIGNAL >> [S] XGA 1 H Position 2/2 Wireless Transmission Transmission Select the installation mode according2/5 to the situation in which the projector is installed. Setup [OK] NG OK [NG] When using in the broadcast mode, it is necessary to set up the ID number into the receiver 3/5 which is conformed to thatWireless of the transmitter. Setup Setup them side by sideInitial as described below.
Broadcast Mode Operation PROJECTOR Mode select 1. P ress the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the HD DATA WIRELESS icon. 2. U se the Point de buttons to move the Mode Select Menu red frame pointer to the Mode Select icon and then press the SELECT button twice. A dialog box appears. 3. Use the Point de buttons to select Broadcast mode and then press the SELECT button. Input ID Input ID Menu English 1.
Broadcast Mode Operation TRANSMITTER 1/1: Output Level Select Noise or interference may appear on images of some projectors when using in the broadcast mode depending on whether the signal reception level of receiver is too high or low. Try to adjust the output level of the transmitter to get the best reception condition for all projectors. 1. Press the MENU button to show the Menu. Press the Point de buttons to select Main Menu "1/6: Broadcast Mode Setup" Menu and then press the SELECT button. 2.
Broadcast Mode Operation PROJECTOR Reception Level 1. P ress the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the HD DATA WIRELESS icon. 2. U se the Point de buttons to move the red frame pointer to Reception level icon and then press the SELECT button. Reception Level Menu 3. The Reception Level (0 to 7) display appears. 0 . . . . . . minimum reception level 7 . . . . . . maximum reception level 5.
Other Basic Operation 5/6: Key Lock TRANSMITTER This function allows you to lock the key operation on the transmitter. To enter a new Lock Key At first, set up a new Lock Key in the transmitter to operate Key Lock function. ✐ If a Lock Key is already set, this menu "Input Lock Key [#]### OK" will not be displayed. 1. Press the MENU button to show the Menu. Press the Point de buttons to select Main Menu "5/6: Key Lock" and then press the SELECT button. "Input Lock Key [#]### OK" will be displayed. 2.
Other Basic Operation Key Lock 5/6 To change Lock Key TRANSMITTER Input Lock Key [#]### OK Input Lock Key #### [OK] 1. Press the MENU button to show the Menu. Press the Point de buttons to select Main Menu "5/6: Key Lock" and then press the SELECT button. Key Lock 1/2 2. Press the Point de buttons to select Sub Menu "2/2: Change Lock Key" and then press the SELECT button. enterLock a number. Press 3. Enter theKey current four-digit Point ed buttons toKey Lock 1/2 number.
Other Basic Operation 2/6: Image Adjust TRANSMITTER You can adjust contrast and brightness of the output signal from the transmitter. 1. Press the MENU button to show the Menu. Press the Point de buttons to select Main Menu "2/6: Image Adjust" and then press the SELECT button. Image Adjust 2/6 Contrast 1/2 Setting Brightness 2/2 Setting Contrast +32 Brightness -32 1/2: Contrast Setting After the step 1; 2.
Other Basic Operation Reset Function of the projector PROJECTOR Reset 1. P ress the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the HD DATA WIRELESS icon. Reset Menu 2. Use the Point de buttons to select Reset and the “Return to Wireless factory default?” appears. Select [Yes] to continue. English 3. Another confirmation dialog box appears, select [Yes] to reset the Wireless setting of Mode select, Input ID and Authentication.
Maintenance and Care Cleaning the cabinet Turn off the transmitter and unplug the AC power cord from the AC outlet before cleaning. Gently wipe the transmitter body with a soft dry cleaning cloth. When the cabinet is heavily soiled, use a small amount of mild detergent and finish with a soft dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet.
Appendix Before calling your dealer or service center for assistance, check the items below once again. - Make sure you have properly connected the transmitter to peripheral equipment. - Make sure all equipment is connected to the AC outlet and the power is turned on. Problem Solutions No power - Plug the AC power cord into the AC outlet. - Check the connection of the AC adaptor and try to re-connect the AC adaptor. - Check the LINK indicator. No image - Check the authentication in the single mode.
Appendix Specifications Interface Component Input Jacks BNC Type x 3 Computer Digital Input Jack DVI-D Terminal x 1 HDMI Input Jack HDMI Terminal x 1 DC IN Jack DC 16 V (AC Adaptor) Power Voltage 100 - 120 V or 200 - 240V, 50/60 Hz Power Consumption DC 16V 1.0A 11.8 [W] at normal, 2.43 [W] at stand-by mode Operating Environment Operating Temperature 41ºF - 95ºF (5ºC - 35ºC) Storage Temperature 14ºF - 140ºF (-10ºC - 60ºC) Mechanical Information Dimensions ( W x H x D ) 10.63" x 1.97" x 8.
Appendix Compliance JAPAN: VCCI Class A, TELEC (Wireless) USA: FCC Part15 Subpart C (Wireless) FCC Part15 Subpart C, Class A Canada: IC RSS-210 (Wireless), IC ICES-003 Class A Europe: R&TTE, EMC, LVD English Countries and Standards HD DATA WIRELESS TRANSMITTER BOX OWNER'S MANUAL 37
Appendix Compatible Signals Specifications V-Freq. [Hz] LCD DISPLAY 480p 31.47 59.88 480p 575p 31.25 50.00 575p 720p - 50 37.50 50.00 720p 720p - 60 45.00 60.00 720p 1080i - 50 28.125 50.00 1080i 1080i - 60 33.75 60.00 1080i SIGNAL INPUT 1 : COMPONENT INPUT 3 : HDMI INPUT 2 : DVI-D 38 H-Freq. [kHz] TERMINAL RESOLUTION VGA 1 640 x 480 31.47 59.94 VGA 1 SVGA 2 800 x 600 37.88 60.32 SVGA 2 XGA 1 1024 x 768 43.363 60.00 XGA 1 WXGA 6 1280 x 768 47.776 59.
Appendix Configurations of Terminals INPUT 2 : DIGITAL DVI-D (DVI 24 Pin) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 T.M.D.S. Data2– T.M.D.S. Data2+ T.M.D.S. Data2 Shield No Connect No Connect DDC Clock DDC Data No Connect 9 10 11 12 13 14 15 16 T.M.D.S. Data1– T.M.D.S. Data1+ T.M.D.S. Data1 Shield No Connect No Connect +5V Power Ground (for +5V) Hot Plug Detect 17 18 19 20 21 22 23 24 T.M.D.S. Data0– T.M.D.S. Data0+ T.M.D.S. Data0 Shield No Connect No Connect T.
OWNER'S MANUAL POA-HDTM01 1AA6P1P5524-- (IFFZ) SANYO Electric Co., Ltd.