Multimedia Projector MODEL PLC-XL45 Owner’s Manual http://www.pureglare.com.
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Large Screen in Limited Space ◆Digital Zoom (for Computer) Short focus lens allows you to project large images from short distance (p.13). ◆ Security Features The Security function helps you to ensure security of the projector.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . .
To the Owner Before installing and operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. This projector should be operated only from the type of power source indicated on the marking label.
Safety Instructions Air Circulation Installing the Projector in Proper Position Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Install the projector properly. Improper Installation may reduce the lamp life and cause fire hazard. CAUTION 20˚ Do not tilt the projector more than 20 degrees from side to side. 20˚ Hot air is exhausted from the exhaust vent.
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Part Names and Functions Front q Focus Lever w Projection Lens e Lens Cover (See page 51 for attaching.) CAUTION q w e r Do not turn on the projector with putting the lens cover on. The light beam may damage lens cover and result in fire hazard. Attach the lens cover while the projector is not in use to avoid scratching the lens surface. t r Exhaust Vents Back r y o u CAUTION !0 Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side.
Part Names and Functions Rear Terminal ✽ q w e r t y u (VARIABLE) RESET USB SERVICE PORT COMPUTER IN 1 / COMPONENT IN COMPUTER IN 2 / VIDEO IN S-VIDEO IN o q USB (Series B) In order to operate the computer with the remote control during a presentation, connect the USB port of the computer to the projector with a USB cable (not supplied) (p.14). w SERVICE PORT This jack is used to service the projector.
Part Names and Functions Top Control q w e r t y u i POWER WARNING LAMP REPLACE FF -O NE TO YS KE T PU IN U EN M N O CT LE SE + E M LU VO E M LU O -V o q SELECT button – Execute the selected item (p.20). – Expand or compress the image in Digital zoom mode (p.33). w POWER ON–OFF button Turn the projector on or off (pp.18 –19). e MENU button Open or close the On-Screen Menu (p.20). r POWER indicator – Lights red when the projector is in stand-by mode. – Lights green during operations.
Part Names and Functions Remote Control e w q POWER ON-OFF button Turn the projector on or off (pp.18, 19). q w VIDEO button Select VIDEO input source (pp.23, 34). e COMPUTER button Select COMPUTER input source (pp.23, 25, 35). r MENU button Open or close the On-Screen Menu (p.20). r !6 t !5 y !4 u !3 i !2 t Point ed 7 8 (VOLUME + / –) buttons – Select an item or adjust the value in the On-Screen Menu. (p.20) – Pan the image in Digital zoom + mode (p.33).
Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Two AA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment. To insure safe operation, please observe the following precautions: ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery.
Installation Positioning the Projector For the projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. ✔Note: •This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance. • The brightness in the room has a great influence on picture quality. It is recommended to limit the ambient lighting in order to get the best image. •All measurements are approximate and may vary from the actual sizes. 3.215’ (0.
Installation Connecting to a Computer Cables used for connection • VGA Cables (Mini D-sub 15 pin)* • USB Cable • Audio Cables (Mini Plug: stereo) (*One cable is supplied; other cables are not supplied with the projector.) Audio Output USB port Monitor Output Monitor Output or Monitor Input External Audio Equipment Audio Input USB cable Audio cable (stereo) USB VGA cable VGA cable Audio cable (stereo) COMPUTER IN 1/ COMPUTER IN 2/ COMPONENT IN MONITOR OUT This terminal is switchable.
Installation Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-VIDEO Cable • Audio Cable (Mini Plug: stereo) (Cables are not supplied with the projector.
Installation Connecting to Component Video Equipment Cables used for connection • Audio Cables (Mini Plug: stereo) • Scart-VGA Cable • Component Cable • Component-VGA Cable (Cables are not supplied with the projector.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100–120 V or 200–240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station.
Basic Operation Turning On the Projector 1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector’s AC power cord into an AC outlet. The POWER indicator turns red. 3 Press the POWER ON-OFF button on the top control or on the remote control. The POWER indicator becomes green and the cooling fans start to operate. The preparation display appears on the screen and the count down starts.
Basic Operation Turning Off the Projector 1 Press the POWER ON-OFF button on the top control or on the remote control, and “Power off?” appears on the screen. 2 Press the POWER ON-OFF button again to turn off the projector. The POWER indicator starts to blink red, and the cooling fans keep running. (You can select the level of the fans’ quietness and running speed. See page 49.) At this time you can unplug the AC power cord even if the fans are still running. 3 “Power off” disappears after 4 seconds.
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. NE TO YS KE POINT button + E M LU VO To close the On-Screen Menu, press the MENU button again. T PU IN Press the SELECT button to show the item data. To adjust the data, use the Point 7 8 buttons. Refer to the relevant pages for more details about each adjustment.
Basic Operation Menu Bar For detailed functions, see Menu Tree on pages 57-58. For computer source q w e r q Guide Window Shows the selected Menu of the On-Screen Menu. t y u i o y Image Adjust Menu Used to adjust the computer image from Contrast, Brightness, Color temp., White balance (R/G/B), Sharpness, and Gamma (pp.31–32) w Input Menu Used to select the input source, Computer or Video (p.25). u Screen Menu e PC System Menu Used to select the computer system (p.26).
Basic Operation Focus Adjustment Adjust the lens focus with the focus lever. Focus Lever Keystone Correction If a projected picture has keystone distortion, correct the image with the Keystone function. Press the KEYSTONE button on the top control or on the remote control. The keystone dialog box appears. Correct keystone distortion with the Point ed buttons. Keystone adjustment can be stored (p.41). Reduce the upper width with the Point e button. Reduce the lower width with the Point d button.
Basic Operation Sound Adjustment POWER WARNING LAMP REPLACE NE TO YS KE T PU IN U EN M N O Direct Operation FF -O Top Control VOLUME+/buttons CT LE SE Volume + Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. E M LU VO E M LU O -V Remote Control Mute Press the MUTE button on the remote control to turn off the sound.
Basic Operation Remote Control AUTO PC button Press the AUTO PC button to operate the Auto PC function. See page 27 for more details. D.ZOOM buttons Press the D.ZOOM buttons to zoom in and zoom out the images. See page 33 for more details. NO SHOW button Press the NO SHOW button to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When the projected image is captured and is set as “User” in the Logo selection (p.
Computer Input Input Source Selection Direct Operation Top Control INPUT button INPUT button Press the INPUT button on the top control or the COMPUTER button on the remote control to select either Computer 1 or Computer 2. Before using the INPUT or COMPUTER buttons, select the correct input source through Menu operation as described below.
Computer Input Computer System Selection The projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If computer is selected as a signal source, the projector automatically detects the signal format and tunes to project proper images without any additional setting. (Signal formats provided in this projector is shown on page 60.
Computer Input Auto PC Adjustment Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical positions to conform to your computer. Direct Operation Remote Control The Auto PC adjustment function can be operated directly with the AUTO PC button on the remote control. AUTO PC button Menu Operation PC Adjust Menu Auto PC Adj. 1 2 Press the MENU button to display the On-Screen Menu.
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas (Mode 1–5) to store those parameters manually adjusted, which allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu.
Computer Input Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select “Reset” and press the SELECT button. A confirmation box appears and then select “Yes.” All adjustments return to their previous figures. Move the red frame pointer to an item and press the SELECT button.
Computer Input Image Level Selection Direct Operation Remote Control IMAGE button Select an image level from among Dynamic, Standard, Real, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 with the IMAGE button on the remote control. Dynamic Standard Dynamic For viewing pictures in a bright room. IMAGE button Real Standard Normal picture level preset on the projector. Blackboard(Green) Image 1 Real Picture level with improved halftone for graphics.
Computer Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item, and then press the SELECT button. The level of each item is displayed. Use the Point 7 8 buttons to adjust each level. Image Adjust Menu Image Adjust Menu icon Move the red frame pointer to the desired item and then press the SELECT button.
Computer Input Store To store the adjusted data, select “Store” and press the SELECT button. The Image Level Menu appears. Use the Point ed buttons to choose one of the four image level and press the SELECT button. A confirmation box appears and then select “Yes.” The stored data can be called up by selecting “Image” in the Image Level Selection on page 30. Move the red frame pointer to the desired image level (from Image 1 to 4) and then press the SELECT button. Quit Exit the Image Adjust Menu.
Computer Input Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the “Custom” is displayed on the screen for a few seconds and then the Aspect dialog box appears. Scale H/V……… Adjust the Horizontal/Vertical screen scale. H&V …………… When set to “On,” the aspect ratio is fixed. “Scale V” appears dimmed and becomes unavailable. Adjust “Scale H,” then the screen scale is automatically modified based on the aspect ratio.
Video Input Input Source Selection (Video, S-Video) Top Control Direct Operation Press the INPUT button on the top control or VIDEO button on the remote control to select “Video.” Before using INPUT or VIDEO buttons, select the correct input source through menu operation as described below. INPUT button POWER WARNING LAMP REPLACE FF -O NE TO YS KE T PU IN N O U EN M INPUT button Video CT LE SE Computer 1 + E M LU VO E M LU O -V Computer 2* *See Note at the bottom of this page.
Video Input Input Source Selection (Component, RGB Scart 21-pin) Direct Operation Top Control Press the INPUT button on the top control or COMPUTER button on the remote control to select Computer 1. Before using INPUT or COMPUTER buttons, select the correct input source through Menu operation as described below.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the AV System Menu icon. 2 Use the Point ed buttons to move the red arrow pointer to the desired system and then press the SELECT button. AV System Menu (Video or S-Video) Video or S-Video Auto The projector automatically detects an incoming video system, and adjusts itself to optimize its performance.
Video Input Image Level Selection Remote Control Direct Operation IMAGE button Dynamic Select an image level from among Dynamic, Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 with the IMAGE button on the remote control. Standard Dynamic For viewing pictures in a bright room. IMAGE button Standard Normal picture level preset on this projector. Cinema Blackboard (Green) Image 1 Cinema Picture level adjusted for the picture with fine tone.
Video Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Video Input Sharpness Press the Point 7 button to decrease the sharpness of the image; press the Point 8 button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point 7 8 buttons to adjust the gamma value to get better balance of contrast (from 0 to 15). Noise reduction Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off……… Disabled.
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. 2 Use the Point ed buttons and move the red frame pointer to the desired function and then press the SELECT button. Screen Menu Screen Menu icon Move the red frame pointer to the desired function and press the SELECT button.
Setting Setting This projector has Setting menu that allows you to set up the other various functions described as follows: 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the item that you want to set and then press the SELECT button. The Setting dialog box appears.
Setting Logo (Logo and Logo PIN code lock settings) Logo select This function allows you to customize the screen logo with Logo select, Capture, and Logo PIN code lock functions. ✔Note: • When “On” is selected in Logo PIN code lock function, Logo select and Capture functions cannot be selected.
Setting Logo PIN code lock Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. Off…… the screen logo can be changed freely from the Logo select menu (p.42). On…… the screen logo cannot be changed without the Logo PIN code. If you want to change the Logo PIN code lock setting, enter a Logo PIN code along the following steps. The initial Logo PIN code is set “4321” at the factory. Enter a Logo PIN code Select a number by pressing the Point ed buttons.
Setting Ceiling Ceiling When this function is set to “On,” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to “On,” the picture is left/right reversed. This function is used to project the image to a rear projection screen. Rear Terminal The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output (p.9).
Setting Input search This function detects the input signal automatically. When finding a signal, the search will stop. Use the Point 7 8 buttons to select one of the following. Off …… Input search does not work. On1 …… Input search works under the situation below. • When the INPUT button on the top control is pressed. • When the COMPUTER button or VIDEO button on the remote control is pressed. On2 …… Input search works under the situation below.
Setting On start On start When this function is set to “On,” the projector is automatically turned on just by connecting the AC power cord to an outlet. ✔Note: • Be sure to turn the projector off properly (see “Turning Off the Projector” on page 19). If the projector is turned off in the incorrect sequence, the On start function does not operate properly. Lamp control You can change the brightness of the screen.
Setting Security (Key lock and PIN code lock) This function allows you to use Key lock, PIN code lock to set the security for the projector operation. Key lock Key lock This function locks operation of the top control and remote control. It helps to prevent operation by an unauthorized person. ……Unlocked. …… Locks operation of the top control. To unlock, use the remote control. …… Locks operation of the remote control. To unlock, use the top control.
Setting Enter a PIN code Enter a PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer. The number changes to "✳". If you fixed an incorrect number, move the pointer to the number you want to correct by pressing the Point 7 button, and then select the correct number by pressing the Point ed buttons. Repeat this step to complete entering a four-digit number. The input numbers change to “✳” for security reasons.
Setting Fan This function provides the following options in the cooling fans’ operation after turning off the projector (p.19). L1 …… Normal operation L2 …… Slower and lower-sound than the normal operation (L1), but it takes longer to cool down the projector. Lamp counter This function is used to reset the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement counter by using this function. See page 54 for operation.
Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. WARNING blinking red Top Control When the temperature inside the projector reaches a certain level, the projector is automatically shut down to avoid overheating.
Maintenance and Cleaning Cleaning the Air Filters Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters become clogged with dust particles, they will reduce cooling fans’ effectiveness and may result in a buildup of internal heat and adversely affect the life of the projector. Clean the air filters by following the steps below. 1 Turn off the projector, and unplug the AC power cord from the AC outlet.
Maintenance and Cleaning Cleaning the Projection Lens CAUTION This projector is equipped with a plastic lens. Do not rub the lens with a hard fiber cloth or hit it with a something hard to prevent the lens from scratching. Do not use a chemical cleaner (liquid and solid) to avoid deteriorating the lens. Unplug the AC power cord before cleaning. First, remove the dust with a blower. Then gently wipe the lens surface. Use a lens cleaning paper moistened with methyl alcohol (methanol).
Maintenance and Cleaning Lamp Replacement When the projection lamp of the projector reaches the end of its life, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow, replace the lamp with a new one promptly. Top Control POWER WARNING LAMP REPLACE This indicator turns yellow when the projection lamp reaches the end of its life.
Maintenance and Cleaning Lamp Replacement Counter Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting. 1 Turn the projector on and press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Use the Point ed buttons to move the red frame pointer to Lamp counter and then press the SELECT button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on pages 14–16. – Make sure all equipment is connected to the AC outlet and the power is turned on. – When you operate the projector with a computer and it does not project an image, restart the computer.
Appendix Some displays are not seen during the operation. – Check the Display function (see page 41). PIN code dialog box appears at start-up. – PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set (see pages 18, 47–48). Computer 2 cannot be selected. – Select Computer 2 in the Terminal function (see page 44). The Terminal function cannot be selected. – The Terminal function cannot be selected after Computer 2 is selected.
Appendix Menu Tree Computer Input/Video Input Input Computer 1 RGB Go to System (1) Component Go to System (2) RGB( Scart ) N/A Quit Computer 2 Go to System (1) Video Auto Go to System (3) Video Go to System (3) S-Video Go to System (3) ✽N/A - - - not applicable Quit Sound Sound Volume 0 - 63 Mute On / Off Quit Computer Input System (1) Mode 1 Mode 2 SVGA 1 ---✽Systems displayed in the System Menu vary depending on an input signal. PC Adjust Auto PC Adj. Fine sync.
Appendix Setting Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i System (3) Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL-N Image Select Dynamic Standard Cinema Blackboard (Green) Image 1 Image 2 Image 3 Image 4 Image Adjust Contrast Brightness Color Tint Color temp. Red Green Blue Sharpness Gamma Noise reduction Progressive Reset Store Setting 0 - 63 0 - 63 0 - 63 0 - 63 High Mid Low XLow Adj.
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER WARNING red/green red Projector Condition LAMP REPLACE yellow The projector is off. (The AC power cord is unplugged.) ✽ The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ✽ The projector is ready to be turned on with the POWER ON-OFF button. ✽ The projector is operating normally.
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. 60 ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq.
Appendix Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Multi-media Projector 10.50” x 4.86” x 9.58” (320 mm x 148 mm x 292 mm) (Not including adjustable feet) 7.1 lbs (3.2 kg) 0˚ to 10.0˚ Panel Resolution LCD Panel System Panel Resolution Number of Pixels 0.
Appendix Accessories Owner’s Manual(CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. Optional Parts The parts listed below are optionally available.
Appendix Configurations of Terminals COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG) Terminal : Analog RGB (Mini D-sub 15 pin) 4 5 10 15 3 9 14 2 8 13 12 1 2 3 4 5 6 7 8 1 7 6 11 Red (R/Cr) Input / Output Green (G/Y) Input / Output Blue (B/Cb) Input / Output 9 10 11 12 13 14 15 ----Ground (Horiz.sync.) Ground (Red) Ground (Green) Ground (Blue) 5V Ground (Vert.sync.) Ground / ----DDC data Horiz. sync. Input/Output (Composite H/V sync.) Vert. sync.
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit number be changed, the factory set number will be invalid. While the projector is locked with the PIN code...
SANYO Electric Co., Ltd. KZ6AC http://www.pureglare.com.
