SONYA instruction B/W CCD Camera VB-3524 Manual Congratulations! This is a newly developed SONYA CCD CAMERA. Please read theses instructions before operating this unit.
This symbol indicates that theta are important operating and maintenance instructions i the literature accompanying this unit. WARNING TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This equipment has naan tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed o provide reasonable protection against harmful interference in a residential installation.
CAUTIONS I SELECTING A LOCATION FOR INSTALLATION * Do not expose the unit to direct sunlight or place it near a heat source. * Be sure 1o use this camera only in conditions with a temperature range of ~ 10°C 10 50°C (14°F to 122'F) and less than 90% humidity, e Do not install the unit in an excessively dusty or humid location, Do not expose the unit to water. The unit is not waterproof. « Do not install the unit in a location which Is subject to excessive vibration or shocks.
i PART NAMES I Side view FLANGE-BACK ADJ. pin LOCK (songfest ¢ 37 } LENS iris output terminal jab] There ara E.l. {electronic iris) / BLC Camera mounting bracket {fightback compensation) ON/OFF . (Installation hole} switch, Al {auto-iris) LENS selector Protective cap switch, and the lens s LEVEL control { tor “DC” type lens Inside Rear view the side cover.
{ CONNECTION I M Lens connection The protective cap is used in order to protect the CCD image device. Remove this cap when using the unit and attach the automatic iris ins (sold separately). (@ Remove the protective cap. NOTE : if the lens is the CS-mount {counterclockwise) type, various lenses can be used, Attach the automatic irks lens.
i CONNECTIONS @ I W Regarding lens attached » This camera s equipped with a 1/2" CCD image, auto-iris circuit (ris medieval control circuity and “Mountain (Refer to *Note™). When the standard field of view (FOV) is desired, use the SONYA 1/2" ate-iris senses (“DC” type, only DC power supply (galvanometer) method excluded amplifier circuits, preset AL {auto-iris} LENS selector switch 10 “DC” at the factory.) sod separately (V CL-CS12QY, f=12mm). The V CL-CSBGY {f = 6mmj) Is a wide angle lens.
i CONNECTIONS addition, it is possible 1o use the present auto-rich lenses included amplifier circulate ('VIDEO” type, video signal and DC power supply method, 8. g. 2/3" C-mount auto-iris lens, etc., set Al LENS selector switch to However, they are necessary 1o attach the C-mount adapter (5 mm, supplied) and change the connections to the Ens Iris plug with 4-pin {supplied) as shown below. Then, If necessary, refer to the lens' instruction manual for iris controls.
CONNECTIONS @ I M Typical system connections @ The basic system for monitoring {or recording) conditions in one location Camera VIDEO IN I VIDEO 1N L)L S Moro = Time apse VOR ) {sold sea) NOTES : # The following table shows the maximum distance for different types of coaxial cables, (Distance ls between the camera and the mutt-video processor, etc.
CONNECTIONS I @ A system with multiple camera locations and one monitor location using a camera switcher unit (4-input) Coaxial cable (sold seeps) Ca moms switcher unit {20! sea} DIVIDED OUT® DIVED IN* Time lapse VCR L {acid vape) “VIDEO OUT" “VIDEO N N [ looseness NOTE : * For additional detailed information conceding connections and related equipment, please consult with your deals.
CONNECTIONS @ W Type of power supply AC ADAPTER #24 VAC Is required for operating MODEL NO. PVT-115 voltage in this camera. Therefore, be sure o use the specified AC adapter as the power supply. The AC adapters model No.
INSTALLATION e There is a installation hole on the bosom for convenient mounting. (shipment state) Installation hole : standard threaded hole o It is also possible to suspend the camera from the top by attaching the carnal mounting bracket to the camera top. Folio the steps below. (D Loosen the two fixing craws (M3 x 6) for tha camera mounting bracket. (2 Loosen the two screws {M3 X 4) located on the camera top. (3) Attach the camera mounting bracket to the top of the camera.
* OPERATION I @ Connect power (24 VAC, 60 subject will soon appear on the Hz), after connecting all of monitor. the equipment. @ Adjust the focus and angle The power indicator will depending on the subject, illuminate to indicate that the installation location. power is on, The image of the NOTES : » Be sure 1o carefully read tha corresponding instruction manual, # The lens iris may not operate properly with some auto irks lenses included AMP, In this case,adjust the sensitivity LEVEL of the ins.
I ELECTRONIC IRIS FUNCTION® . * This camera is equipped with a newly developed the ELECTRONIC IRIS function, adopting built-in electronic shutter technology. The ELECTRONIC IRIS operation is equivalent to changing the electronic shutter speed. When a incoming light level becomes high, the unit automatically adjusted the light level by shifting the shutter speed 10 a faster one. The faster the shutter speed, the darker the picture becomes.
i ELECTRONIC [RIS FUNCTION® I NOTES : » If the ELECTRONIC IRIS function is used under fluorescent light, the picture periodically changes dus to a flicker phenomenon, In this case, operate the camera under incandescent lighting or set the £.1. {electronic iris) switch to “OFF” and use an auto-iris lens.
i BACK LIGHT COMPENSATION FUNCTION I Under fightback {counter-light) conditions, the lens iris is properly {Inside the side cover} controlled by setting the BLC {spaceflight compensation) switch to ON “ON". The clean pictures, therefore, OFF E. can be obtained on the monitor ON screen with the center zone BT t Eight-measuring system of the unit.
ADJUSTMENT OF MECHANICAL FOCUS POSITION I The picture may become out of focus especially during zooming if the pickup surface of the lens is not correctly postulation with relation 1o the flange-back if the image becomes out of focus, make the adjustment by following the spats blow. First of all, loosen the lock screw (M2, head) located on the side with a fine-tipped screwdriver. Set the zoom lens to the “telephoto” position and then use the focus ring {knob) te focus the image.
LINE PHASE ADJUSTMENT(D Before shipment Is made, each camera is adjusted in such a manner that vertical sync signal phase between each camera Is coincidental with the zero-cross point of the household AC fine {120V, 80HzZ) so that no adjustment is necessary for fine locked operation. When two or more cameras are Installed, It the picture on the monitor roils while switching from camera may be necessary to make a phase adjustment.
I LINE PHASE ADJUSTMENT .
TROUBLESHOOTING I This camera has been precision adjusted at the factory, however, in the event that any of the problems listed below do occur, refer to this troubleshooting table, and follow the instructions for the appropriate adjustment or inspection.
i FEATURES I « 24 VAC operation with fine dock. » Line phase (V) adjustable externally. » Interior-coordinated compact design. » 100% solid state, including the image device (1/2" interline transfer CDC. This makes the camera long-lasting and reliable. » Performance : 570 TV sines of resolution ars achieved with no after image or burning of image device, » Minimum required illumination is . (F1.2) » Ease of use in any application is achieved through the compact size.
SPECIFICATIONS I Scanning system Interlace Image device Synchronizing system Resolution Video output elev! Video S/N ratio Minimum required illumination: Gain control Electronic iris function iris range Back light compensation Lens-iris level contort Lens mount Environmental conditions Power requirement Po war consumption Weight Flange-back adj. Accessories EiA standard 525 TV lines, 60 fisids/sec.
SPECIFICATIONS @ I {External dimensions} 108.5 | 15 89,5 Standard 1/4” — UNCUT 22 Threaded hole {Unit: mm) For the customers In Canada This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Pour la clientele incarnadine Cet apparel numerous de [a Class A respect routes [es exigences du Regalement sur le material derailleur du Canada. 21350 Lassen Street, Chats worth, CA91311 1ACEP1P0566--B .