L53H4/US2 (VCC-5984) GB 2003, 1, 7 INSTRUCTION MANUAL COLOR CCD CAMERA About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . . . .
L53H4/US2 (VCC-5984) GB 2003, 1, 7 INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Pour la clientèle canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre).
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 4 1 2 Power input terminal 24 V AC input terminal (AC 24 V, GND) 3 2 3 External sync composite video signal input connector (VBS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 6 Flange-back adjustment screw (FLANGE BACK ADJ.) 7 5 6 8 7 Flange-back lock screw (FLANGE BACK LOCK) 8 Camera installation bracket 1 2 3 2 The bracket can be fixed at the top or bottom of the camera.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 9 Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F F Camera setup section (under the cover) 9 These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS").
L53H4/US2 (VCC-5984) GB 2003, 1, 7 CONCERNING AUTO-IRIS LENSES VR301 DC VIDEO A. I. LENS DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens 2 L 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. 3 2 CS mount type lens 3 CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. 1 Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 CONNECTIONS 1 (A) 3 AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) : VIDEO IN : VIDEO OUT ~ ~ GND Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), AC adaptor and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 24 V AC adaptor.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 7-a 9 Control name Position 1 High speed electronic shutter (ES) setting 1/60 sec.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS Electronic shutter settings and electronic iris settings 1 When all of these switches are down, electronic shutter (1/60 sec or auto iris setting) is enabled. The electronic shutter can be set to one of 7 speeds as shown in Table A. Furthermore, when all switches are up, electronic iris setting is enabled. Notes on the electronic shutter: • Using the high speed electronic shutter indoors with low lighting, will give darker pictures.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS Backlight compensation setting 45 This camera has two different backlight compensation functions: Normally backlight compensation switch 6 (MULT) and 7 (CENT) are set to the down (OFF) position. Change 6 7 the backlight compensation switch settings depending on the conditions. • MULT mode: Use this position when applying backlight compensation to the whole of the screen.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS White balance adjustment 6 Normally the switch 8 (WB) is set to the down (ATW: auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 (WB) to the up (M: manual) position, then adjust the colour. • Turn RED (VR302) to set the red ratio and/or BLUE (VR303) to set the blue ratio.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS Lens iris adjustment 9 If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. VR301 L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window. • If the subject background is extremely bright or dark. • If the brightness of the picture on the monitor is not correct.
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre.
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) : PLL 2:1 interlace : 1/3 inch solid state image device CCD : 811 (H) x 508 (V) : 768 (H) x 494 (V) Interlace Image device Picture elements Effective picture elements Synchronizing system : Internal sync, External sync, Automatically switchable Resolution : 520 TV lines horizontally, 350 TV lines vertically Video output level : 1.
SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at
L53H4/US2 (VCC-5984) GB 2003, 1, 7 Printed on recycled paper 1AC6P1P2624-L53H4/US2(0103KPS-CZ) SANYO Electric Co., Ltd.
