http://www.sapido.com.tw/ 1 User Manual 1.
FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions Frequency range - 2400.0 - 2483.5 MHz Country Bulgaria France Italy Luxembourg Norway Russian Federation Country Reason/remark General authorization required for outdoor use none and public service. Military Radiolocation use. Refarming of the 2.
Safe Seating Gestures You should follow the manufacturer’s instructions for adjusting the backrest to fit your body properly. An adjustable chair that provides firm, comfortable support is best. Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor. The back of the chair should support your lower back (lumbar region). http://www.sapido.com.tw/ 4 User Manual 1.
Table of Contents Chapter 1 Introduction ................................................................................................................. 8 1.1 Overview ...................................................................................................................... 8 1.2 Features ....................................................................................................................... 8 1.3 Specifications.............................................................
4.1.2 Wireless LAN setup from Web Browser .......................................................................... 37 4.1.2.1 Multiple APs ....................................................................................................................... 39 4.1.2.2 Enable Universal Repeater Mode..................................................................................... 40 4.2 Wireless Security Setup.......................................................................................
8.8 Others......................................................................................................................... 86 8.9 USB Device ................................................................................................................ 86 Chapter 9 Appendices................................................................................................................ 87 9.1 Operating Systems .................................................................................
Chapter 1 1.1 Introduction Overview Whether in-car Internet, campus network access, Internet activities at tradeshows, or just a home network without ADSL reaches, the RB-1632 can help you establish the Internet connection in minutes. Moreover, by adapting latest, state-of-the-art WLAN technology, RB-1632 implements cutting-edge "Active-ECO" algorithm, which controls automatically the power consumption in accordance with WLAN and Ethernet activities.
1.3 Specifications Interface Function Others WAN Port 1 x 10/100 Mbps RJ45, with auto MDI/MDIX LAN Port 1 x 10/100 Mbps RJ45, with auto MDI/MDIX Wireless Built-in Mini PCI Slide Switch Router / AP / WiFi AP mode exchange function.
1.3.1 Six Views of Product Appearance Power Plug Power Adapter DC5V/0.5A with mini-USB B type male connector Operation Mode Switch Router, AP, and WiFi AP operation modes Reset Button Press “Reset” button over 10 seconds. When status indicator turns from flashing to solid, the process is completed. All settings are back to default. Ethernet Port 2 RJ-45 Ethernet 10/100 Ports 1.3.
Chapter 2 System and Network Setup RB-1632 is an easy to setup and wireless device for various application and environment. It can be used in conference room, hotel, even in transportation. To begin with RB-1632, you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. Internet Account for XDSL/Cable Modem, broadband or 3G One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card.
2.1.2 AP Mode Switch to AP mode, if a router is already set at the hotel or the house, and you want to make the wireless LAN communication. 2.1.3 Wi-Fi AP Mode Switch to AP mode, if a router is already set at the hotel or the house, and you want to make the wireless LAN communication. Switch to WiFi AP Mode, If you want to connect to the internet wirelessly through PC and game device without wireless LAN function equipped, http://www.sapido.com.tw/ 12 User Manual 1.
2.2 Connecting to RB-1632 by using Web Browser Prepare the followings before the connection: 1. PC or Notebook for setup 2. Ethernet cable Setp 1. Make sure that the switch is shifted to "Router" (Router mode). Setp 2. Connect RB-1632 to xDSL/ Cable modem with the Ethernet cable, WAN to LANs. Setp 3. Connect this product's Internet port and the modem's LAN port (or Network Termination Unit). 2.
Windows 95/98/ME - please go to section 2.2.1 Windows 2000 Windows XP Windows Vista 2.3.1 - please go to section 2.2.2 - please go to section 2.3.3 - please go to section 2.3.4 Windows 95/98/ME 1. Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network icon, and Network window will appear. Select “TCP/IP”, then click ”Properties”. 2. Select “Obtain an IP address from a DHCP server”, and then click ”OK”. http://www.sapido.com.
2.3.2 Windows 2000 Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Dial-up Connections icon; double click Local Area Connection, and Local Area Connection Properties window will appear. Select “Internet Protocol (TCP/IP)”, then click “Properties”. 1. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. 2.3.3 1.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ 16 User Manual 1.
2.3.4 1. Windows Vista / Windows 7 Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”. 2.
2.4 Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default Gateway” (In this example, the gateway IP address of router is 192.168.1.1) http://www.sapido.com.tw/ 18 User Manual 1.
NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with “169.x.x.x”, please recheck network connection between your computer and router, and / or go to the beginning of this chapter, to recheck every step of network setup procedure. 2.4.
http://www.sapido.com.tw/ 20 User Manual 1.
Chapter 3 Internet Connection This Chapter describes how to setup RB-1632 to the internet. RB-1632 is delivered with the following factory default parameters. Default IP address: 192.168.1.1 (Router Mode) 192.168.1.254 (AP Mode) 192.168.1.254 (WiFi AP Mode) Default IP subnet mask: 255.255.255.0 Web login user name: admin Web login password: admin 3.1 Plug and Play The RB-1632 supports three types of Internet connection method: 3G/3.5G modem card, wire or wireless connection via xDSL/Cable modem.
3.2.1 WAN Interface- Ethernet Port The WAN access type is depended on the service that you contract with the provider. The RB-1632 provides five selections for the WAN access type, Static IP, DHCP Client, PPPoE, PPTP, L2TP. Check with your ISP if you don’t know the WAN type. 3.2.1.1 Static IP Select WAN under the IP Config menu, and choose Ethernet Port for the WAN Interface. Its associated setting will show up. http://www.sapido.com.tw/ 22 User Manual 1.
Item Description WAN Access Type Select “Static IP” IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Default Gateway Input ISP Default Gateway Address. DNS Input DNS information which is provided by your ISP Clone Mac Address Some ISPs require MAC address registration.
3.2.1.2 DHCP Client Item Description WAN Access Type Select "DHCP Client" Host Name You can keep the default as the host name, or input a specific name if required by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration.
3.2.1.3 PPPoE Item Description WAN Access Type Select "PPPoE" User Name Input your user name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Service Name Input the service name provided by your ISP. http://www.sapido.com.tw/ 25 User Manual 1.
Connection Type Three types for select: Continues, Connect on Demand, and Manual. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data.
Item Description WAN Access Type Select "PPTP" Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration.
the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset 3.2.1.5 Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. L2TP Item Description WAN Access Type Select "PPTP" Server IP Address / Host http://www.sapido.com.tw/ Input your server IP address or Host Name provided by your ISP. 28 User Manual 1.
Name If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration.
Item Description APN (Access Point Name) Enter the access point name. If you do not know the setting information for APN, check with your 3.5G service provider. User Name Enter the User Name supplied by the provider. Password Enter the password supplied by the provider. Phone Number Enter the subscribing access point's phone number. Always / Dial on demand If your 3G USB adapter is a pay-as-you-go plan base, select “Dial on demand” and disconnect the connection when you don't use the internet.
3.2.3 Setp 1. WAN Interface- Wireless Select WAN under the IP Config menu, and choose 3.5G usb dongle for the WAN Interface. Its associated setting will show as below. http://www.sapido.com.tw/ 31 User Manual 1.
3.3 AP Mode-Using as a Access Point Make sure to shift the mode into AP Mode. Note: 1. Before sliding the switch modes, please power-off the router firstly. Moreover, please stay over 10 seconds between power-off / power-on condition. When this product is used as an access point, the IP address has to be changed. The default IP under AP mode is 192.168.1.254. Setp 1. Open a Web browser, and enter http://192.168.1.254 (Default Gateway) into the blank. Setp 2.
Item Description IP Address The default IP address is 192.168.1.254 Subnet Mask Enter the Subnet Mask address. Default Gateway Enter the Default Gateway address for LAN interfaces. DHCP Select DHCP type: Client, Disable, or Server under different environment. DHCP Client Range When enable DHCP server, you can fill in the start and end IP address; client will be assigned an IP address from the range.
Login to enter. http://www.sapido.com.tw/ 34 User Manual 1.
Chapter 4 4.1 Wireless LAN Setup Wireless setup There are two ways to setup wireless LAN with RB-1632. You can use either way to setup Wireless LAN. 4.1.1 WPS setup You can setup wireless LAN easily by using the WPS button if both WLAN router and the WLAN adapter (client) are WPS supported. Before starting the setup, please check the things below: 1. Get ready for Internet connection with RB-1632. 2. The WLAN adapter is finished installation and plug in your computer/ laptop.
Setp 1. Open Wireless adapter utility. Setp 2. Press the WPS button (1) from RB-1632 and wait for Wireless/WPS LED light (2) changed into red. Setp 3. Back to the WLAN adapter utility and click its “PBC” button. The utility will start searching the destination connection. Setp 4. Confirm the information form the Utility. http://www.sapido.com.tw/ 36 User Manual 1.
Setp 5. After completes the WPS setup. Please confirm that it can be connected to the Internet. 4.1.2 Wireless LAN setup from Web Browser The Wireless Basic Settings include Band, Mode, SSID, Channel Number and other wireless settings. http://www.sapido.com.tw/ 37 User Manual 1.
Item Description Disable Wireless LAN Interface Turn off the wireless service. Band Select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). Mode Select the mode. It has 3 modes to select: (AP, Client, WDS, AP+WDS). Multiple AP: Please check Section 4.1.2.1. SSID Service Set identifier, users can define to any or keep as default. Channel Width Please select the channel width, it has 2 options: 20MHZ, and 40MHZ.
Enable MAC Clone (Single Ethernet Client) Clone the MAC address for ISP to identify. Enable Universal Repeater Mode (Acting as AP and Client simultaneously) Allow to equip with the wireless way conjunction upper level, provide the bottom layer user link in wireless and wired way in the meantime. (The IP that bottom layer obtains is from upper level.) Please also check Section 4.1.2.
Active Client List Display the properties of the client which is connecting successfully. Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. 4.1.2.2 Enable Universal Repeater Mode The router can act as Station and AP at the same time. It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage.
4.2 Wireless Security Setup Here users define the security type and level of the wireless network. Selecting different methods provides different levels of security. Please note that using any encryption may cause a significant degradation of data throughput on the wireless link. There are five Encryption types supported: “None”, “WEP”, “WPA (TKIP)”, ”WPA2(AES)”, and “WPA2 Mixed”. Enabling WEP can protect your data from eavesdroppers.
It is a safety system by using authentication to protect your wireless network. 2. Encryption – WPA (WPA, WPA2, and WPA2 Mixed), WPA Authentication Mode (a). Enterprise (RADIUS): Please fill in the RADIUS server Port, IP Address, and Password (b). Personal (Pre-Shared Key): Pre-Shared Key type is ASCII Code; the length is between 8 to 63 characters. If the key type is Hex, the key length is 64 characters. 3. Apply Change & Reset: Click on ‘Apply Changes’ to save setting data.
click on “Apply Changes” to save the new addition. To delete a MAC address, select its corresponding checkbox under the Select column and click on “Delete Selected” button. Take the wireless card (MAC address: 0018F8638A54) as the example. (1) Please select Deny Listed in Wireless Access Control Mode first, and then fill in the MAC address what you plan to block in the MAC Address field. Click Apply Changes to save the setting.
(3) The wireless client will be denied by the wireless router. http://www.sapido.com.tw/ 44 User Manual 1.
Chapter 5 Router Mode Security Setup This section contains configurations for the RB-1632’s advanced functions such as: virtual server, DMZ, and Firewall to provide your network under a security environment. 5.1 NAT 5.1.1 Visual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. Item Description Enable Port Forwarding Select to enable Port Forwarding service or not.
Reset Click Reset to cancel. Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP. Configuration: 5.1.2 DMZ The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing. When enabled, this feature opens all ports to a single station and hence renders that system exposed to intrusion from outside.
Enable DMZ It will enable the DMZ service if you select it. DMZ Host IP Address Please enter the specific IP address for DMZ host. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 5.2 Firewall 5.2.1 Port Filtering When enabled packets are denied access to Internet/filtered based on their port address. Item Description Enable Port Filtering Select Enable Port Filtering to filter ports.
Protocol Please select the protocol type of the port. Comment You can add comments for this regulation. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. Current Filter Table It will display all ports that are filtering now. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. Reset You can click Reset to cancel.
Item Description Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. Local IP Address Please enter the IP address that needs to be filtered. Protocol Please select the protocol type of the IP address Comment You can add comments for this regulation. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. Current Filter Table It will display all ports that are filtering now.
Item Description Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses. MAC Address Please enter the MAC address that needs to be filtered. Comment You can add comments for this regulation. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. Current Filter Table It will display all ports that are filtering now. Delete Selected & Delete All Click Delete Selected will delete the selected item.
Item Description Enable URL Filtering Please select Enable MAC Filtering to filter MAC addresses URL Address Please enter the MAC address that needs to be filtered. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. Current Filter Table It will display all ports that are filtering now. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table.
6.1 Dynamic DNS Setting Router You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it will re-register its domain-name-to-IP-address mapping with the DDNS service provider. This is the way Internet users can access the router through a domain name instead of its IP address. Note: make sure that you have registered with a DDNS service provider before enabling this feature. Please enter Domain Name, User Name/Email, and Password/Key.
In Advanced Settings page, more 802.11 related parameters are tunable. Item Description Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is 2346. RTS Threshold This value should remain at its default setting of 2347. The range is 0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended.
particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. Fill the range from 0 to 2347 into this blank. Beacon Interval Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. The allowed setting range is 20-1024 ms..
Please follow the instructions to setup WDS connections. Step 1. Please check the MAC address and Channel number from the upper lever device. Step 2. Set the connection mode to “AP+WDS” from “Wireless Basic Setting”, and then select the channel number (in this example is "11”). Click Apply Changes to save the setting. http://www.sapido.com.tw/ 55 User Manual 1.
Step 3. Enable WDS function from the page – “WDS Setting”, and then fill in the upper level device MAC address. Click Apply Changes to save the setting data. http://www.sapido.com.tw/ 56 User Manual 1.
Step 4. The WDS AP List will show the WDS device MAC address after reboot. Step 5. Set “Broadcast SSID” to disable from page “Wireless Basic Setting”. http://www.sapido.com.tw/ 57 User Manual 1.
Step 6. Go to the upper level device WDS setting page and fill in the MAC address Input the MAC address here. Step 7. You will receive an IP address from the upper lever device. http://www.sapido.com.tw/ 58 User Manual 1.
6.2.2 WPS This page allows user to change the setting for WPS (Wi-Fi Protected Setup). Using this feature could let your wireless client atomically synchronize it’s setting and connect to the Access Point in a minute without any hassle. RB-1632 could support both Self-PIN or PBC modes, or use the WPS button (at real panel) to easy enable the WPS function. PIN model, in which a PIN has to be taken either from a sticker label or from the web interface of the WPS device.
Setp 2. Press the WPS button (3) from the adapter for more than 2 seconds. Setp 3. Waiting for around 30 seconds to 3 minutes, open a web browser to check the internet connection. Please also refer to section 4.1.1 WPS set up for more details. 6.3 System Management Router AP WiFi AP This section including Change Password, Upgrade Firmware, Profiles Save, Time Zone Setting, UPnP Setting, and Language Setting. It is easy and helpful for users making more detailed settings. http://www.sapido.com.
6.3.1 Change Password Users can set or change user name and password used for accessing the web management interface in this section. Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 6.3.2 Upgrade Firmware This function can upgrade the firmware of the router. There is certain risk while doing firmware upgrading. Firmware upgrade is not recommended unless the significant faulty is found and published on official website.
Caution: To prevent that firmware upgrading is interrupted by other wireless signals and causes failure. We recommend users to use wired connection during upgrading. Caution: The firmware upgrade will not remove your previous settings. Reset button: On the back of this router, there is a reset button. If you can not login the administrator page by forgetting your password; or the router has problem you can’t solve. You can push the reset button for 10 seconds with a stick.
a. Save Configuration (1) Click Save. (2) Please click “Save” to save the configuration to your computer. http://www.sapido.com.tw/ 63 User Manual 1.
(3) Select the location which you want to save file, then click “Save”. b. Load configuration file. (1) Click Browser (2) Select configuration file then click “Open”. http://www.sapido.com.tw/ 64 User Manual 1.
(3) Click Upload to upload configuration file to RB-1632. (4) After 90 seconds, RB-1632 will reboot automatically. (C) Reload factory default setting. 1. Please click Reset. http://www.sapido.com.tw/ 65 User Manual 1.
(2) Please click “OK” to start reload factory default setting to RB-1632. (3) After 90 seconds, RB-1632 will reboot automatically. 6.3.4 Time Zone Setting Users can synchronize the local clock on the router to an available NTP server (optional). To complete this setting, enable NTP client update and select the correct Time Zone. http://www.sapido.com.tw/ 66 User Manual 1.
Item Description Current Time Users can input the time manually. Time Zone Select Please select the time zone. Enable NTP client update Please select to enable NTP client update or not. Automatically Adjust Please select to enable Automatically Adjust Daylight Saving or not. Daylight Saving NTP Server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. Apply Changes & Reset & Please click on Apply Changes to save the setting data.
6.4 Log & Status The category provides Network Config and Event Log status for users to know the operation status. 6.4.1 Network Config Users can check the Internet status under this category, including Firmware version, Wireless setting, Connecting Time, WAN, TCP/IP …information. http://www.sapido.com.tw/ 68 User Manual 1.
6.4.2 Event Log You may enable the event log feature here. http://www.sapido.com.tw/ 69 User Manual 1.
Item Description Enable Log You may choose to enable Event Log or not. System all, Wireless, & DoS Please select the event you want to record. Enable Remote Log You may choose to enable the remote event log or not. Log Server IP Address Please input the log server IP Address. Apply Changes & Refresh & Click on Apply Changes to save the setting data. Click on Refresh to renew the system time, or on Clear to clear all the record.
6.5 Logout This function logs out the user. http://www.sapido.com.tw/ 71 User Manual 1.
Chapter 7 DDNS Service Application DDNS is a service changes the dynamic IP to the static IP. The settings of DDNS can solve the problem of being given the different IP by router every time. After setting the Router, your host name would correspond to your dynamic IP. Moreover, via the host name application, it could be easier for you to use FTP, Webcam and Printer remotely. Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static host name.
Step 2. Fill in the form as required, and then click on Create Account button. http://www.sapido.com.tw/ 73 User Manual 1.
Step 3. When you got this account created message, close it, and check your mailbox. You would get a mail from DynDNS website. Step 4. Click on the indicated address within your mail to confirm. Step 5. Click on login. http://www.sapido.com.tw/ 74 User Manual 1.
Step 6. Click Add New Hostname. Step 7. Put in your favorite hostname and service type, and then click Create Host after finished. http://www.sapido.com.tw/ 75 User Manual 1.
Step 8. Your hostname has been created when you see the following page. http://www.sapido.com.tw/ 76 User Manual 1.
Step 9. Click “Activate Service” Filish http://www.sapido.com.tw/ 77 User Manual 1.
Chapter 8 8.1 1. Q&A Installation Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is installed between the XDSL line and the LAN. Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub (switch or computer). 2. Q: Why does the throughput seem slow? A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter.
8.3 1. IP Address Q: What is the default IP address of the router for LAN port? A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0 2. Q: I don't know my WAN IP. A: There are two ways to know. Way 1: Check with your Internet Service Provider. Way 2: Check the setting screen of RB-1632. Click on Status & Log item to select Network Configuration on the Main Menu. WAN IP is shown on the WAN interface. 3.
A: Possible Solution 1: Make sure that your Ethernet connect properly and securely. Make sure that you've plugged in the power cord. Possible Solution 2: Make sure that your PC is using an IP address within the range of 192.168.1.2 to 192.168.1.254. Make sure that the address of the subnet mask is 255.255.255.0. If necessary, the Default Gateway data should be at 192.168.1.1. To verify these settings, perform the following steps: Windows 95, 98, or My Users: 1.
6. Click on OK button. 3. Q: Web page hangs, corrupt downloads, or nothing but junk characters is being displayed on the screen. What do I need to do? A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate" feature of your NIC as a temporary measure. (Please look at the Network Control Panel, in your Ethernet Adapter's Advanced Properties tab.) 4. Q: Why can't I connect to the Web Configuration? A: you can remove the proxy server settings in your web browser. 8.5 1.
A: Periodically, a new Flash Code is available for RB-1632 on your product supplier’s website. Ideally, you should update RB-1632’s Flash Code using Firmware Upgrade on the System Management menu of RB-1632 Settings. 5. Q: My 11n Mobile Server Router cannot connect to the ISP? A: There are three possible solutions. 1. Check the Cable/XDSL modem is power on. 2. Check the Cable/XDSL link light is on to verify a good physical connection. 3.
8.6 1. Wireless LAN Q: Why couldn’t my wireless notebook work on-line after checking? A: Generally, Wireless networks can sometimes be very complicated to set up, particularly if you're dealing with encryption and products from different vendors. Any number of variables can keep your workstations from talking to each other. Let's go over some of more common ones. For starters, verify that your router and your workstation are using the same SSID descriptions.
2. Q: My PC can’t locate the Wireless Access Point. A: Check the following: Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode.) The SSID on your PC and the Wireless Access Point are the same. Remember that the SSID is case-sensitive. So, for example “Workgroup” does NOT match “workgroup”. Both your PC and the Wireless Access Point must have the same setting for WEP.
A: The Wireless Router processes the data passing through it, so it is not transparent. Use the Special Application feature to allow the use of Internet applications which do not function correctly. If this does solve the problem, you can use the DMZ function. This should work with almost every application, but: It is a security risk, since the firewall is disabled. Only one (1) PC can use this feature. 5. Q: I can’t connect to the Wireless Router to configure it.
A: Maybe your USB devices and RB-1632 are not compatible. So if you want to know whether your inserted device such as USB Web Camera, USB Printer or USB HDD corresponds with RB-1632, please check with your product supplier. 3. Q: What is the maximum number of IP addresses that the XDSL Router will support? A: The Router will support to 253 IP addresses with NAT mode. 5. Q: Is the Router cross-platform compatible? A: Any platform that supports Ethernet and TCP/IP is compatible with the Router. 8.8 1.
Chapter 9 9.1 Appendices Operating Systems 1. Microsoft：Windows 2000, XP, Vista 32bit and the following related versions. 2. Apple：Mac OS X 10.4.7, Leopard and the following related versions. 3. Linux：Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions. 9.2 Browsers 1. Internet Explorer ver. 6 and 7 and the following related versions. 2. FireFox ver. 2.0.0.11 and the following related versions.3. 3. Safari ver. 3.04 and the following related versions. 9.
