Specifications

ManualsBrandsSargent and Greenleaf ManualsHome building and Decor6120

page 1

I. General Information

a. About Your Lock

b. PIN Positions

c. Changing the Batteries

d. Quick Reference Tables

e. Keypad Tamper Indicator (Optional)

II. Management Reset Code (MRC) and Master Code (MC)

a. Management Reset Code

b. Master Code

III. Creating, Changing and Deleting Codes

a. Creating Supervisor Code

b. Creating User Codes

c. Changing Codes

d. Deleting Codes

e. Detecting Active User Positions

IV. Time Delay

a. Time Delay Duration

b. Opening Window Duration

c. Time Delay Override

d. Creating, Changing, Deleting the TDO Code

V. Management/Employee Access

VI. Duress Function

VII. Audit Trail Options

a. Event Audit Trail

VIII. Codes—General Information

VIII. Speciﬁcations and Warranty

Model 6124 / 6125 Multiple User Access

Electronic Safe Lock

Setup and Operations Guide

2006, Sargent & Greenleaf, Inc.

Document 630-656ENG

Revised 5/25/06

Sargent & Greenleaf, Inc.

A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.

PO Box 930

Nicholasville, KY 40356

Phone: (800)-826-7652 Fax: (800)-634-4843

Phone: (859)-885-9411 Fax: (859)-887-2057

Sargent & Greenleaf S.A.

9, chemin du Croset

1024 Ecublens, Switzerland

Phone: +41-21 694 34 00

Fax: +41-21 694 34 09

Note: This lock has been Listed by Underwriters Laboratories for use with the following

S&G keypad(s):

6120-0XX, 6120-2XX, 6160-2XX (IP Series), 61KP-1XX, 61KP-2XX

Summary of content (11 pages)

PAGE 1
Model 6124 / 6125 Multiple User Access Electronic Safe Lock Setup and Operations Guide I. General Information a. b. c. d. e. II. About Your Lock PIN Positions Changing the Batteries Quick Reference Tables Keypad Tamper Indicator (Optional) Management Reset Code (MRC) and Master Code (MC) a. Management Reset Code b. Master Code III. Creating, Changing and Deleting Codes a. b. c. d. e. Creating Supervisor Code Creating User Codes Changing Codes Deleting Codes Detecting Active User Positions IV.
PAGE 2
I. General Information a. About Your Lock Each time you press a number, letter, or other character on the keypad of your Model 6124 or 6125 electronic safe lock, it beeps and the red LED flashes. If it doesn’t, check your batteries to make sure they are fresh and connected properly, then try again. (See Changing the Batteries, paragraph C.) The lock responds with various beep () sequences to indicate different conditions. The  symbols in examples show the number of beeps you hear.
PAGE 3
d. Quick Reference Tables Command Reference: Each of the following commands (CMD) begins a code sequence to perform a specific function. CMD Function 22* Change six-digit user code. 28* Download the event audit trail. 32* Set up the Management/Employee enabling/disabling of user codes. 38* Enable/disable the duress function 43* Identify the type of lock. 46* Program the time delay override option. 55* Enable/disable user codes (with Master or Supervisor Code, in Management/Employee mode).
PAGE 4
e. Keypad Tamper Indicator—Required for VdS rating (Optional: Tamper-indicating keypad must be ordered) If a tamper-indicating keypad is installed, the lock records each time the lock keypad housing is unseated or removed from the base. If the housing is disturbed, the Keypad Tamper Indicator beeps an SOS warning signal the next time you attempt to enter a valid access code. The lock will not open; it beeps the SOS: 3 short/high beeps, 3 short/low beeps, 3 short/high beeps. This signal is repeated twice.
PAGE 5
For example, to use the MRC of 9, 1/0, 8, 9, 2, 7 and create a Master Code of 6, 5, 4, 3, 2, 1: 6 7 * 9 1/0 8 9 2 7 #  6 5 4 3 2 1 #  6 5 4 3 2 1 #  2. MRC Audit Trail This audit trail lets you know how many times the MRC has been used to reset the lock. Immediately after the new Master Code is set with the MRC, the lock beeps once for each time the MRC has been used, including the current usage. Note: Usage of the MRC is recorded in the event audit trail. b.
PAGE 6
b. Creating User Codes Using the Master or Supervisor Code, create new User Codes. For each user, create a unique 6-digit code and assign a PIN position (2 through 8). PIN position 9 is also available as a normal User Code if the Time Delay Override feature is turned off. Note that PIN positions 4 through 8 are not available if the lock’s duress function is enabled.
PAGE 7
a. Time Delay Duration If the time delay parameter has been set and you want to change it, enter a user code to start the time delay. When Time Delay expires (the lock emits 10 rapid beeps) and the opening window period has begun, set your Time Delay minutes.
PAGE 8
c. Time Delay Override With Time Delay Override (TDO), you define whether or not you can override Time Delay, in case you need to open the lock before the time delay expires - for example, by a cash carrier. If time delay has been programmed, the following steps must be performed during the opening window period. Important Note: PIN position 9 is where the Time Delay Override Code is stored.
PAGE 9
V. Management/Employee Access During everyday operation of the lock, the Manager or Supervisor ‘enables’ the lock, and the lock can then be opened by User Codes until it is “disabled”. There are two versions of the enable/disable function: • In the first version, only the Master and the Supervisor can both enable and disable the lock. • In the second version, Users may disable the lock (Master and Supervisor can still disable the lock). a.
PAGE 10
VI. Duress Function (Order Duress Module Separately) Your lock has duress capability (a silent alarm option). Installation of a duress signal box (duress module) is required for proper connection to your existing alarm system. Use the instructions provided with the module to ensure accurate installation and connection. a. Enabling the Duress Feature When the lock is installed with the duress module, you need to enable duress feature.
PAGE 11
VIII. Specifications and Warranty Specifications for Models 6124 and 6125 Electronic Safe Locks and 61KP Keypads Lock Dimensions Width: 2.4” (61 mm) Height: 1.1” (30 mm) Length: 3.32” (84 mm) Keypad Dimensions 4 inches diameter (101 mm) Height: 1.44” (36 mm) Weight 6124: 1 pound (45 g) 6125: 1 pound (45 g) Housing/base: 0.7 pound (28 g) Shipping Weight 6124: 1.75 pounds (74 g) 6125: 1.