User Manual

ManualsBrandsSARGENT ManualsSafety11 Line Lever Lock

INSTALLATION INSTRUCTIONS FOR

11 Line U.S. Patent No. 6,626,018

Item Description Qty.

1 Inside Lever 1

2 6 Lobe Security Set Screw, 2

1/4-28 x 11/64" 2

3 Rose 2

4 Rosette 2

5 Inner Collar 1

6 Inner Sleeve 1

7 Bearing Assembly 1

8 Aligning Pin 1

9 Outer Sleeve (with captive Collar) 1

10 Cylinder 1

11 Outside Lever 2

12 Keys 1

13 Latch Assembly 4

14 Screw, Flat Hd, #8-32 x 3/4" 1

15 Strike (800 shown)

To view helpful video installation tips, scan the Microsoft

Tags with

your mobile phone. Download the free mobile app at http://gettag.mobi.

Code Latchbolt Functions

A 15

B 04, 05, 13, 15-3, 16, 17, 30, 37, 38

C 65

D 44, 50, 54

K 24

LATCHBOLTS ARE NOT INTERCHANGEABLE.

Code stamp

location

NOTE– CONSULT FACTORY FOR

CORRECT TEMPLATE INFORMATION

FOR 11G93, 11G94 AND 11G94-2

FUNCTIONS

FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com

2013 SARGENT Manufacturing. All rights

reserved. Reproduction in whole or in part without

the express written permission of SARGENT

Manufacturing is prohibited.

A7469K

2" (51mm)

1-3/4" 44mm)

Mark for

1" hole (25mm)

at center of

door thickness

2-3/4" (70 mm)

BACKSET

3-3/4" (95 mm)

BACKSET

5" (127 mm) BACKSET

FOLD HERE

IMPORTANT

Place fold on

HIGH EDGE

of beveled door

Mark center for

2-1/8" crossbore

hole at correct

backset

IMPORTANT

2 x 5/32" (4 mm) Dia

2-1/8" (54 mm) Diameter

2-1/4" (57mm)

Mark for 1" hole

at center of

door thickness

FOLD HERE

IMPORTANT

Place fold on

HIGH EDGE

of beveled door

Mark center for

2-1/8" crossbore

hole at correct

backset

IMPORTANT

1-3/4"

2-3/4" (70 mm) BACKSET

3-3/4" (95 mm) BACKSET

5" (127 mm) BACKSET

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR 11 Line U.S. Patent No. 6,626,018 FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.
PAGE 2
1 Door Preparation 2 1-1/8" • Fold template on door and mark hole centers 38" Finished floor High edge of beveled door 3 • Mark centerline on jamb • Mark outline of strike 2-1/4" • Cut recess for latch bolt • I nstall strike; secure with two screws IMPORTANT Guardbolt stops on strike when door is closed GUARDBOLT 2-1/8" Hole 2-1/8" 1" 1" 5/32" DEEP RECESS • Bore 2-1/8" • Bore 1" hole 1/8" DESIRED BACKSET STRIKE • Cut rectangular front recess 4 5 Lock Disassembly 1.
PAGE 3
7 Sleeve Installation Scan to see a video of this installation step. 1. With driver tips aligned, insert outside sleeve first. Dimple must face door edge 2. Thread outside collar by hand. Tighten to bearing assembly with wrench 3. Insert inside sleeve. Dimple must face door edge 4. Thread inside collar by hand. Tighten to bearing assembly with wrench Inside 4 3 Caution: If excessive wrench torque is required, stop and check alignment of driver tips 8 Cam Orientation 1.
PAGE 4
Function Specific Directions - Lever Installation For functions not shown proceed to step 10 Inside Sleeve Lock lever by button Rotate cam until lever catch button can be depressed, holding cam in rotated position Function Function Description 05 24 44 65 04 Entrance/Office Entry Service Station Privacy/Bathroom Storeroom/Closet Rotate cam until lever catch button can be depressed, holding cam in rotated position Scan to see a video of this installation step.