User guide

ManualsBrandsSARGENT ManualsSafety281 Series Cast Iron Closer

A7313B

of Sargent Manufacturing Company is prohibited.

MODEL 281 POWERGLIDE SERIES

INSTRUCTIONS FOR INSTALLING SARGENT DOOR

CLOSERS WITH "H" HOLDER ARMS

81 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.

LEFT

HAND DOOR

RIGHT

HAND DOOR

PULL

HINGE SIDE

PULL

HINGE SIDE

STOP (PUSH) SIDE STOP (PUSH) SIDE

TANDARD APPLICATION*

(

TYPE 25-H ARM)

TOP JAMB

APPLICATION*

(TYPE 25-H, 25-HZ, 25-HZA)

PARALLEL ARM

APPLICATION*

(TYPE 25-PH9)

CLOSER

MOUNTED

ON STOP SIDE

OF DOOR

CLOSER MOUNTED ON FRAME

ON STOP SIDE OF DOOR

NOTE: FOR H8 ARM MOUNTING

EE DATA SHEET ENCLOSED

UMBER OF TURNS OF SPRING POWER ADJUSTING SCREW

ROM FACTORY SETTING

(USE CHART AS GUIDE ONLY)

OOR WIDTH

(INCHES)

OVER 48

EXTERIOR DOORS

FACTORY SET

-5 CW

5-8 CW

-13 CW

13-15 CW

UP TO 19 CW AS REQ.

NTERIOR DOORS

1-5 CCW

ACTORY SET

1-5 CW

5 CW AND UP AS REQ.

PPROXIMATE

DOOR WEIGHT (POUNDS)

115

130

150

155

170

180

NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT

FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)

DOOR WIDTH

(INCHES)

OVER 48

281

EXTERIOR DOORS

2-7 CW

7-11 CW

11-15 CW

15-17 CW

UP TO 19 CW AS REQ.

APPROXIMATE

DOOR WEIGHT (POUNDS)

110

115

130

150

155

165

170

180

ADJUST SPRING POWER ACCORDING TO CHART

1/4" ALLEN SPRING POWER

ADJUSTING SCREW

INCREASE

POWER

DECREASE

POWER

*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS

ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING

SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW

COUNTERCLOCKWISE.

USE

PAGE 2

USE

PAGE 3

USE

PAGE 4

NOTE: FOR PH4 ARM MOUNTING,

SEE DATA SHEET ENCLOSED.

1-5 CCW

FACTORY SET

1-8 CW

8 CW & UP AS REQ.

INTERIOR DOORS

LOSER MOUNTED ON

INGE SIDE OF DOOR

CLOCKWISE

(CW)

COUNTER CLOCKWISE

(CCW)

STANDARD & TOP JAMB APPLICATIONS

A7313B H arm 5.08:Layout 1 7/3/08 8:32 AM Page 1

Summary of content (6 pages)

PAGE 1
A7313B H arm 5.08:Layout 1 7/3/08 8:32 AM Page 1 MODEL 281 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS 281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.
PAGE 2
A7313B H arm 5.08:Layout 1 7/3/08 8:32 AM Page 2 281 STANDARD APPLICATION FOR "H" ARM INSTRUCTIONS IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING ARM TYPE “H” HOLDER MAX. DOOR OPENING DIM. A DIM. B STANDARD 105∞ 7 3/4" 13 1/4" ALTERNATE 160∞ MOUNTING ALTERNATE MOUNTING IS RECOMMENDED FOR ADA COMPLIANT DOORS DIM. "B" DIM.
PAGE 3
A7313B H arm 5.08:Layout 1 7/3/08 8:32 AM Page 3 281 TOP JAMB APPLICATION INSTRUCTIONS A B C Copyright © 2003, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
PAGE 4
A7313B H arm 5.08:Layout 1 7/3/08 8:32 AM Page 4 281 PARALLEL ARM APPLICATION INSTRUCTIONS MAX. DOOR OPENING DIM. A DIM. B 120∞ 4 1/2" 10 1/2" HINGE PIVOT: BUTT, OFFSET PIVOTS, SWING CLEAR, CENTER HUNG OR INVISIBLE HINGES 2 1/2" 1 1/4" 1/2" 180∞ 1 1 5/8" 7 5/8" DOOR LEFT HAND DOOR SHOWN. RIGHT HAND DOOR DIMENSION OPPOSITE. 7/8" 2 DO NOT USE THIS MOUNTING FOR “SWING CLEAR” HINGES. 3 THIS DIMENSION IS TAKEN FROM HINGE EDGE OF DOOR FOR INVISIBLE HINGES.
PAGE 5
A7313B H arm 5.08:Layout 1 7/3/08 8:33 AM Page 5 FINAL ADJUSTMENT AND REGULATING PROCEDURE DELAYED ACTION VALVE (OPTIONAL) BACKCHECK VALVE DELAYED ACTION RANGE CLOSING SPEED RANGE LATCHING SPEED VALVE 1/4" SPRING POWER ADJUSTMENT SCREW CLOSING SPEED VALVE A B REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED. USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT.
PAGE 6
A7313B H arm 5.08:Layout 1 7/3/08 8:33 AM Page 6 USING MORTISE NUTS WITH SARGENT DOOR CLOSER 1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY AND FOOT ON DOOR AND FRAME. 2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR. 3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT SHOWN FOR MOUNTING THE CLOSER BODY. 4.