User Manual

Joule 3.0 User Guide page 29
1. Press the MODE button until Menu mode appears.
2. Select Sensors.
3. Select the desired sensor type (Power, Cadence, Speed, Heart Rate or RU); make sure
sensor is awake and isolated from other active sensors by 65 feet/20 meters).
4. For Power sensors, select type of power meter. (PowerTap, Indoor Cycle -IC, ANT+, SRM,
Quarq)
5. Select Start Pairing. Note: If a heart rate strap was purchased with Joule™ with it
will already be paired to Joule™ .
6. After successful pairing, Joule™ should display a five digit code corresponding to the
sensor. (Pairing may take up to 60 seconds).
7. Select Name and/or Wheel Circumferance to edit if desired.
8. Select Active Sensor to save as the primary sensor and return to sensor list.
9. Only activate sensors will be found by Joule™.
Follow above steps for Setting Up any Power, Cadence, Speed, Heart Rate or Resistance Unit sen-
sor. Note: It is recommended the Auto Zero setting for PowerTap remain selected as yes, unless
using a track hub.
Chapter 5: Sensors
Setting Up Sensors
Joule™ is compatible witn many ANT+ sesnors, each having a unique code. A sensor is defined as
ANT + compatible power meters, cadence sensors, speed sensors, heart rate straps and CycleOps
resistance units. Joule™ needs to be paired to each sensor to ensure proper functionality.
Power Sensor:
>
- None
Cadence Sensor:
>
>
Speed Sensor:
>
- None
>
Heart Rate Sensor:
>
- None
>
RU Sensor
>
-None
>
Y
>
>
Auto Zero (Y or N):
Y
>
Re-Pair Sensor
>
Re-Pair Sensor
>
Delete Sensor
>
PT Data
>
Pair
>
Pair New Sensor
>
Back
<
Report
Menu
Sensors
- None
Select Sensor
>
- Po werSensor1 >
Sensor ID
>
Add PowerTap
>
The Gun Show
>
Torque O set
>
Torque O set
>
Torque O set
>
>
Add IC Power
>
Add ANT+
>
Pair New Sensor
>
Back
<
Report
Menu
Po wer Sensor
Activate Sensor
>
>
>
00000
>
Wheel Circumference:
>
02096
>
Auto Zero (Y or N):
>
Y
>
Auto Zero (Y or N):
>
Y
>
>
Auto Zero (Y or N):
Y
>
Re-Pair Sensor
>
Cancel Pairing
>
Delete Sensor
>
Calibration
>
Pair
>
Pair New Sensor
>
Back
<
Report
Menu
Po werSensor1
Sensor ID:
PowerSensor1
Name:
>
Start Pairing
>
Activate Sensor
>
>
>
PAIRING
>
Wheel Circumference:
>
02096
>
Auto Zero (Y or N):
>
Y
>
Auto Zero (Y or N):
>
Y
>
>
Auto Zero (Y or N):
Y
>
Re-Pair Sensor
>
Cancel Pairing
>
Delete Sensor
>
Calibration
>
Pair
>
Pair New Sensor
>
Back
<
Report
Menu
Po werSensor1
Sensor ID:
Po werSensor1
Name:
>
Start Pairing
>
Activate Sensor
>
>
>
12345
>
Wheel Circumference:
>
02096
>
Auto Zero (Y or N):
>
Y
>
Auto Zero (Y or N):
>
Y
>
>
Auto Zero (Y or N):
Y
>
Re-Pair Sensor
>
Cancel Pairing
>
Delete Sensor
>
Calibration
>
Pair
>
Pair New Sensor
>
Back
<
Report
Menu
Po werSensor1
Sensor ID:
Po werSensor1
Name:
>
Start Pairing
>
blink