Installation & Assembly

ManualsBrandsSARIS ManualsBike & Sport RacksLock Bar Wall Mounted Bike Rack

Assembly Instructions

3-8 Bike

VERTICAL RACK

Bicycle Storage & Parking Solutions

Optional

Tools Required:

• 9/16” Combination wrench & 7/16“ Combination wrench

• Hammer drill (for anchors)

• ½” concrete drill bit (for anchors)

• Tape measure

Mounting Hardware – part # 6264 (sold separately)

Recommended for

8023, 8024, 8043, 8044; REQUIRED for

8033, 8034, 8063, 8064

WARNINGS:

• Mounting vertical rack to oor is recommended for single sided models

(8023, 8024, 8043, 8044) and REQUIRED for double sided models (8033,

8034, 8063, 8064).

• Manufacturer and seller expressly disclaim any and all liability for personal

injury, property damage or loss, whether direct, indirect or incidental,

resulting from the incorrect attachment, improper use, inadequate

maintenance, or neglect of this product.

WARRANTY:

We warrant this product to the rst consumer to be free from defect in

material and workmanship for a period of one year from date of purchase

(please retain your sales slip for your records). Any product or part thereof

found to be defective within that period will be replaced without charge

provided that (1) the product was not misused; (2) no alterations or

modications were made; (3) its failure resulted from a defect in material or

workmanship and not from normal wear expected in the use of the

product; (4) the product or part is delivered, freight prepaid, to Saris Cycling

Group. Manufacturer’s only obligation shall be to replace such products or

parts proved to be defective. Damage to mounting surface is not covered

under warranty.

SKU Decsrip�on Bike Spacing Ceiling Height Footprint W/Bikes

8023 3 bike, single sided, non locking ver�cal rack 18" 84" 54"X46"

8024 4 bike, single sided, non locking ver�cal rack 18" 84" 75"X46"

8043 3 bike, single sided, locking ver�cal rack 18" 84" 54"X90"

8044 4 bike, single sided, locking ver�cal rack 18" 84" 75"X90"

8033 6 bike, double sided, non locking ver�cal rack 18" 84" 54"X46"

8034 8 bike, double sided, non locking ver�cal rack 18" 84" 75"X46"

8063 6 bike, double sided, locking ve

r�cal rack 18" 84" 54"X90"

8064 8 bike, double sided, locking ver�cal 18" 84" 75"X90"

Product shown 8024

Summary of content (4 pages)

PAGE 1
VERTICAL RACK Bicycle Storage & Parking Solutions Assembly Instructions 3-8 Bike Tools Required: • • • • 9/16” Combination wrench & 7/16“ Combination wrench Hammer drill (for anchors) ½” concrete drill bit (for anchors) Tape measure Optional Mounting Hardware – part # 6264 (sold separately) Recommended for 8023, 8024, 8043, 8044; REQUIRED for 8033, 8034, 8063, 8064 WARNINGS: • Mounting vertical rack to floor is recommended for single sided models (8023, 8024, 8043, 8044) and REQUIRED for double sided
PAGE 2
A B C D E F F H I J K L M Product shown 8024 Part 6006 Bike tray, locking 6003T Bike tray, non locking Ver�cal 2” square side bar 2” x 24” x 1” C channel stabilizing foot Connec�on plate, 6” x 6” Horizontal cross bar, c channel, 54” long Horizontal cross bar, c channel, 72” long Tube caps (2” square plas�c) Carriage Bolt, 1/4 – 20 x ½” Carriage Bolt, ¼-20 x 2.
PAGE 3
STEP 1: LEG ASSEMBLY • Assemble side supports and connect feet (part D - 2x24x1) to side support vertical tubes (part C), using connection plate (part E), and Carriage Bolt (part K) Step 1(x2) 3/8 X 3” Holes closer to the edge on the ground. STEP 2 : HORIZONTAL CROSS BAR • Attach Horizontal Cross bar (Part F) to each vertical side support (part C), using carriage bolt (Part J) Shown: 8044, 4 bike, single sided, locking vertical rack Step 2 C 1/4 X 2.
PAGE 4
STEP 3: ATTACH WHEEL TRAYS TO FRAME SINGLE AND DOUBLE SIDED: • Standard spacing – standard bike spacing is 18” on center. Use “Square” oriented holes on cross bar (part F) to achieve standard bike spacing. To connect Bike trays to rack, use bolt (part I) and nut (Part M) to secure Bike Tracs to the cross bar (part F). • Note: An additional Bike Trac can be added to all increase bike capacity by 1 bike for single sided racks, and 2 bikes for double sided racks. This will change bike spacing to 14.