Technical data

64
sample itself or by system errors such as com-
ing, sticking etc. So what to do with the incor-
rect results? To through them and hide them
from the authorities? To eliminate that problem
completely the ERWEKA HADs is available with
video monitoring of six dissolution vessels of
one or both connected dissolution testers. The
video monitoring allows recording of each test-
run in combination with real-time overlapping
dissolution profile to identify disturbances such
as coning etc. and to get the visual impression
of 24 hours in 2 minutes. The video monitoring
is a very powerful tool for method development
as well for troubleshooting.
230V/50Hz 72-210-0001
230V/60Hz 72-210-0002
115V/60Hz 72-210-0003
127V/60Hz 71-210-0004
1. Dissolution Tester/s
up to two Dissolution Testers can be con-
nected to one HADs
 Dissolution Tester, Type DT 726/LH-1000
The 8 position - 6 test-stations DT 726 is the
ideal NG Dissolution Tester for software
controlled Dissolution System. While con-
trols are performed via the PC the unit itself
shows its run conditions at individual bright
LE displays. The DT 720 series includes
such features as MagniShaft "tool-free" stir-
rer exchange system, fully corrosion-free
construction (alloy; fibreglass etc.), one-
piece mould water bath with powerful exter-
nal flow-through heater, fast moving column
for the drive heat etc. "Low-Head" configura-
tion ("High-Head" on special request).(for
Dual system 2x DT 726/LH-1000 have to be
selected) 14-070-6001
 Automated Sample Withdraw System
Driven bar with attached sampling- and re-
placement tubes (st.steel) for sample-
withdraw and -replacement. Microprocessor
controlled to withdraw at the USP/EP speci-
fied sampling height (midway) for each com-
bination of media volume and stirrer type.
14-x7x-x4xx
 Automated Sample Withdraw System
Same as above - but with 8 additional elec-
tronic temperature sensors for display and
documentation of the media temperature in
each Vessel. 14-x7x-x9xx
 Titanium Sampling- and Replacement
tubes (instead of st.steel), corrosion-free
80-090-0200
 Cleaning Reservoir for sampling station;
with 3 compartments to avoid any cross-
contamination. 80-089-0000
 Electronic (waterless) calibration System
for calibration of PT 100 temperature sen-
sors, recommended with 10-092-0001
2. Options
 7 test-stations (instead 6); Position 7 with
drive shaft; Additional price 14-x7x-7xxx
 External electronic temperature sensor PT
100 for display of water bath - or media tem-
perature. Extended instrument menu for
one-point calibration routine as well as cali-
bration hard-copy documentation.
84-070-0100
 Automated Tablet Drop Magazine (instead
manual operation of standard tablet drop
magazine). With temperature check before
drop. 84-070-0010
 Illumination of the water bath by integrated
LEDs 84-090-0112
 Vessel Centering Ring for centering and
holding ERWEKA Vessel 84-060-3000
 USP compliant Vessel, Polycarbonate
80-000-1001
 USP compliant Vessel, glass, standard
80-000-1002
 USP compliant Vessel, glass, numbered
with certificate of compliance
85-000-1002
 USP compliant Vessel, UV resistant brown
glass 80-000-1004
 USP compliant Vessel, UV resistant glass,
numbered with certificate of compliance
85-000-1004
 Full-Teflon Paddle and Shafts (one piece
mould); numbered
MagniShaft 84-000-7001
UniShaft 84-010-7001
St. Steel 84-010-7002