CG2 Series Quick Guide CG208TT CG212TT Korean Chinese Thermal Transfer Type 203 dpi/305 dpi German English CG2 Series CG208DT CG212DT Direct Thermal Type 203 dpi/305 dpi
FCC WARNING English You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Safety Precautions This section describes how to use the printer safely. Be sure to read it carefully before using the printer. Pictographic Symbols This instruction manual and the printer labels use a variety of pictographic symbols to facilitate safe and correct use of the printer and to prevent injury to others and property damage. The symbols and meanings for them are given below. Be sure to understand these symbols well before reading the main text.
Caution English Do not place in areas with high humidity Power cord • Keep the power cord away from • Do not place the printer in areas with high humidity or hot devices. Getting the power where condensation forms. If cord close to hot devices could condensation forms, cause the cord’s covering to immediately turn off the power melt and cause a fire or switch and do not use the electrical shock. • When unplugging the power printer until it dries.
Precautions for Installation and Handling Printer operation can be affected by the printer environment. Refer to the following instructions for installation and handling of CG2 Series. Select a Safe Location Place the printer on a surface that is flat and Keep the printer out of high temperature and level. humidity. Do not place the printer on a location that produces vibration. Avoid locations subject to extreme or rapid changes in temperature or humidity.
Table of Contents Safety Precautions ········································································· I Precautions for Installation and Handling ···································· III English Unpacking····················································································· 1 Names of Parts ············································································· 3 Loading Paper ·············································································· 7 Cut Position Adjustm
Unpacking Unpack the box, and then set up the printer. Leaflet (Global waranty) English Accessory box Cushioning material (top) Printer Cushioning material (bottom) Box The shape of the cushioning material (cushions that hold the printer in place) may differ slightly from the diagram shown above. 1 CG208i_E_02.
Checking Accessories Make sure that you have received all of the following items in the package. If there are any accessories missing, contact your nearest dealer or the store where you purchased the printer. Quick Guide (this manual) English Leaflet (Global warranty) AC power cord AC adapter ▲ About the Box Please retain both the box in which the printer was packed and the cushioning material (cushions that hold the printer in place).
Names of Parts ▲ Printer Unit (Unit Exterior) Operation panel English Top cover Cover open/close latch Label discharge outlet ▲ Back (USB + LAN Interface) USB connector LAN connector DC input power terminal (Power connector) ▲ Back (USB + RS-232C Interface) USB connector RS-232C connector DC input power terminal (Power connector) 3 CG208i_E_02.
When Top Cover Is Opened ▲ For CG208/212DT Print head Paper holder English Paper holder slide lever Paper sensor Platen roller ▲ For CG208/212TT Print head Ribbon unit Paper holder Paper holder slide lever Paper sensor Platen roller 4 CG208i_E_02.
When Top Cover Is Opened (Cutter Type (Optional)) ▲ For CG208/212DT Paper holder Paper holder slide lever Paper sensor English Platen roller Cutter unit ▲ For CG208/212TT Paper holder Paper holder slide lever Paper sensor Platen roller Cutter unit 5 CG208i_E_02.
When Top Cover Is Opened (Dispenser Type (Optional)) Paper holder Paper holder slide lever Paper sensor Platen roller Dispenser paper sensor English Backing paper discharge outlet (When the dispenser unit is open) Dispenser unit ▲ Operation Panel POWER button Press this button to turn the power on or off. ON LINE (POWER) lamp The lamp lights green when the printer is online and blinks green when the printer is offline.
Loading Paper Roll paper Paper feed direction Front English This printer can print on roll paper and fan-folded paper. The method of loading the paper is different for roll paper and fan-folded paper. The printer uses a sensor to detect I-marks in the paper in order to precisely position the print content. Be sure to use genuine Sato paper in this printer. Do not use non-standard paper. Gap 3 mm 1.
Loading Roll Paper (Continuous/Cutter Type) 1 Pull the cover open/close latches 1 on both sides of the printer toward you to unlock the top cover, and then open the top cover 2. ② English ① ① 2 While holding the paper holder slide lever, adjust the width of the paper holder 1 to match the paper size. ① ① Paper holder slide lever 3 Load the paper into the paper holder. 8 CG208i_E_02.
4 After pulling out the paper, pass the paper through the paper sensor. When using a cutter type, place the leading edge of the paper on top of the platen roller. 5 6 English Paper sensor Close the top cover. Press the top cover from above in the direction of the arrows until it clicks into position. When the printer is offline, the ON LINE (POWER) lamp blinks. Press the FEED/ LINE button 1. The printer is online and the ON LINE (POWER) lamp lights.
Loading Fan-folded Paper (Continuous/Cutter Type) Pull the cover open/close latches on both sides of the printer toward you to unlock the top cover, and then open the top cover. English 1 2 3 Pass the paper through the opened window at the rear of the unit. While holding the paper holder slide lever, adjust the width of the paper holder 1 to match the paper size. After pulling out the paper, pass it through the paper sensor.
5 Close the top cover. Press the top cover from above in the direction of the arrows until it clicks into position. When the printer is offline, the ON LINE (POWER) lamp blinks. Press the FEED/ LINE button 1. The printer is online and the ON LINE (POWER) lamp lights. When the printer is ready, press the FEED/LINE button to output the top part of the paper. English 4 ① ON LINE (POWER) lamp CAUTION • After printing, the print head and surrounding area are hot.
Loading Roll Paper (Dispenser Type) Pull the cover open/close latches on both sides of the printer toward you to unlock the top cover, and then open the top cover 1. ① English 1 2 Open the dispenser unit. Dispenser bar Dispenser unit 3 Remove the lead label leaving only the backing paper, and load the paper in the paper holder. After pulling out the paper, pass the paper through the paper sensor. Pass the paper over the dispenser bar so as to cover it. Paper sensor 12 CG208i_E_02.
Load the backing paper so that it sticks out from the bottom of the dispenser unit. If the paper is not taut, roll the paper on the paper holder so that the paper is taut. Next, tightly close the dispenser unit by pressing it in the direction of the arrow. English 4 Output label Output backing paper 5 Close the top cover. Press the top cover from above in the direction of the arrows until it clicks into position. 13 CG208i_E_02.
6 When the printer is offline, the ON LINE (POWER) lamp blinks. Press the FEED/ LINE button 1. The printer is online and the ON LINE (POWER) lamp lights. When the printer is ready, press the FEED/LINE button to output the top part of the paper. ① English ON LINE (POWER) lamp CAUTION • After printing, the print head and surrounding area are hot. Be careful not to get burned when replacing paper immediately after printing. • Touching the edge of the print head with bare hands could result in an injury.
Cut Position Adjustment Label Cut The label-cut position should be between labels or at the area with only the backing paper. English Label Backing paper Cut position Cut Position Adjustment If the cutting position is not at the regular position, use the Phillips tip of the potentiometer adjustment screwdriver attached to the side of the paper holder to adjust the potentiometer for the cut position.
Cutting Paper with Perforated Lines For paper with perforated lines, cutting on or in front of the perforated lines is prohibited. Cutting in those locations could cause the printer to malfunction. If paper is cut at or before the perforation, use the Phillips tip of the potentiometer adjustment screwdriver to adjust the potentiometer for the cut position so that the paper is cut after the perforation.
Replacing the Cutter 123 —456 English Over time, the cutter loses its cutting ability and begins to show signs of wear. Replace the cutter unit at this time. Contact the store, dealer, or Support Center for purchasing options. 1 2 3 —4 5 6 Potentiometer for Adjustment This potentiometer is for servicing the printer. Do not change the potentiometer unless specifically instructed to do so. Potentiometer for adjustment 17 CG208i_E_02.
Loading Carbon Ribbon Pull the cover open/close latches 1 on both sides of the printer toward you to unlock the top cover, and then open the top cover 2. English 1 ② ① ① 2 Pull the lever on the middle of the ribbon unit toward you to pull out the ribbon unit. Lever Ribbon unit 18 CG208i_E_02.
3 After setting the carbon ribbon in the right side of the ribbon supply unit 1, press the core guide 2. ① Core guide 4 After setting the ribbon core in the right side of the ribbon windup unit 1, check that the projecting part on the printer is securely inserted into the opening on the roll. Next, press the core guide 2. English ② ① ② 19 CG208i_E_02.
Pass the carbon ribbon from the ribbon supply unit beneath the print head to the ribbon windup unit. Affix the carbon ribbon to the ribbon core using tape, etc., and wind it up several times in the direction shown by the turn arrow. English 5 Wind up several times in the direction shown by the turn arrow. 6 Close the top cover. Press the top cover from above in the direction of the arrows until it clicks into position. 20 CG208i_E_02.
7 When the printer is offline, the ON LINE (POWER) lamp blinks. Press the FEED/ LINE button 1. The printer is online and the ON LINE (POWER) lamp lights. When the printer is ready, press the FEED/LINE button to output the top part of the paper. ① English ON LINE (POWER) lamp CAUTION • After printing, the print head and surrounding area are hot. Be careful not to get burned when replacing the carbon ribbon immediately after printing.
Connecting to a Computer Standard Interface English ▲ USB + LAN Type LAN connector USB connector 1 Turn on the printer while pressing the FEED/LINE button. Continue pressing the FEED/LINE button until the ON LINE (POWER) lamp blinks green. Each time you press the FEED/LINE button, the ON LINE (POWER) lamp 2 indicator changes. When using the USB connector, check that the ON LINE (POWER) lamp is alternating between green and red.
▲ USB + RS-232C Type RS-232C connector English USB connector 1 Turn on the printer while pressing the FEED/LINE button. Continue pressing the FEED/LINE button until the ON LINE (POWER) lamp blinks green. 2 Each time you press the FEED/LINE button, the ON LINE (POWER) lamp indicator changes. When using the USB connector, check that the ON LINE (POWER) lamp is alternating between green and red. When using the RS-232C connector, check that the ON LINE (POWER) lamp is blinking green.
Expansion Interface (Optional) English ▲ Wireless LAN Interface 1 Turn on the printer while pressing the FEED/LINE button. Continue pressing the FEED/LINE button until the ON LINE (POWER) lamp blinks green. 2 Each time you press the FEED/LINE button, the ON LINE (POWER) lamp indicator changes. When using the wireless LAN connector, check that the ON LINE (POWER) lamp is alternating between green and red. 3 Press the FEED/LINE button for at least three seconds to register the connector type.
Keypad (Simple input device (Optional)) English RS-232C connector Communication cable Keypad (Simple input device) 1 Turn on the printer while pressing the FEED/LINE button. Continue pressing the FEED/LINE button until the ON LINE (POWER) lamp blinks green. 2 Each time you press the FEED/LINE button, the ON LINE (POWER) lamp indicator changes. When using the keypad, check that the ON LINE (POWER) lamp is blinking red.
Turning On the Power Power Setting Plug the DC power cord of the AC adapter into the printer and turn on the power. Connect the AC power cord to the AC adapter. English 1 AC adapter AC power cord 2 Connect the printer AC adapter AC power outlet. When plugging the DC power cord into the printer's power connector, make sure the DC power cord connector is oriented properly. When plugging in the DC power cord to the printer, use one hand to hold the printer while using the other hand to plug in the cord.
The plug of the supplied AC power cord is 3-pronged. One of the 3-pronged electrodes is dedicated to grounding. When the outlet is a 3-prong type, plug the AC power cord directly into it. English 3 CAUTION • Be sure to connect the ground wire to the ground. Not connecting the ground wire could result in electrical shock. • The power cord set supplied with this printer is only for use with this printer. Do not use it for other electrical products.
Cleaning the Printer This printer is used to print barcodes and data containing important information. If the printer parts become dirty, the printer may not be able to print barcodes and data accurately, and it may malfunction. Therefore, it is important to regularly clean the printer. Recommended Cleaning Schedule English It is recommended that you clean the printer with the cleaning sheet (sold separately) after six paper rolls or 300 meters of paper are discharged.
Basic Specifications CG208DT 203 dpi (8-dot/mm) Direct Thermal CG212DT 305 dpi (12-dot/mm) CG208TT CG212TT 203 dpi 305 dpi (8-dot/mm) (12-dot/mm) Thermal Transfer (Direct Thermal/ Thermal Transfer) Printing effective area 56 mm wide × 600 mm pitch 56 mm wide × 400 mm pitch Label issuing Standard: Continuous mode, Tear off mode, Sensor off mode mode Optional: Dispenser mode, Cutter mode Printing speed 50, 75 or 100 mm/sec (Setting: 50, 75, 100) 2, 3 or 4 inches/sec (Setting: 2, 3, 4) Unprintable area Label
English Model name Printing direction (Characters/ Barcode) Barcode ratio Magnification ratio (Characters/ Barcode) Self-diagnostic function CG208DT CG212DT CG208TT CG212TT Characters: 0, 90°, 180°, 270° Barcode: Parallel 1 (0°), Parallel 2 (180°), Serial 1 (90°), Serial 2 (270°) Dimensions Weight Power specifications Power consumption Environmental conditions (Temperature/ Humidity) Options 128 (W) × 235 (D) × 173 (H) (mm) 1.5 kg 1.
▲Label size CG212DT/CG212TT Continuous type Pitch: 9 to 403 mm Width: 15 to 63 mm Cutter type Pitch: 25 to 403 mm Width: 15 to 63 mm Tear-off type Pitch: 15 to 403 mm Width: 15 to 63 mm Continuous type Pitch: 6 to 400 mm (Backing paper 9 to 403 mm) Width: 15 to 60 mm (Backing paper 18 to 63 mm) Cutter type Pitch: 22 to 400 mm (Backing paper 25 to 403 mm) Width: 15 to 60 mm (Backing paper 18 to 63 mm) Tear-off type Pitch: 12 to 400 mm (Backing paper 15 to 403 mm) Width: 15 to 60 mm (Backing paper 18 to 63 mm
English 32 CG208i_E_02.
