2008 Saturn Astra Owner Manual Seats and Restraints ......... 1-1 Front Seats .................... 1-2 Rear Seats .................... 1-7 Safety Belts ................... 1-8 Airbag System .............. 1-23 Child Restraints ............. 1-37 Keys, Doors and Windows ............................ 2-1 Keys ............................. 2-2 Doors and Locks ............ 2-5 Theft-Deterrent Systems ... 2-7 Windows ...................... 2-10 Mirrors ......................... 2-12 Sunroof .....................
ii Preface This manual describes features that may or may not be on your specific vehicle. Keep this manual in the vehicle for quick reference. SATURN and the SATURN Emblem are registered trademarks, and the name ASTRA is a trademark of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. Saturn reserves the right to make changes after that time without further notice. Litho in U.S.A.
Preface Index To quickly locate information about the vehicle use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Cautions and Notices There are a number of safety cautions in this book. A box with the word CAUTION is used to tell about things that could cause injury if the warning is ignored. { CAUTION These mean there is something that could hurt you or other people.
iv Preface ✍ NOTES
Seats and Restraints Seats and Restraints Care of Safety Belts .........1-22 Replacing Safety Belt System Parts After a Crash ...........................1-23 Airbag System Front Seats Manual Seats .....................1-2 Seat Height Adjuster ...........1-2 Lumbar Seat Adjustment ....1-3 Reclining Seatbacks ...........1-3 Head Restraints ..................1-5 Heated Seats .....................1-6 Rear Seats Rear Seat Operation ...........1-7 Safety Belts Safety Belts ........................
1-2 Seats and Restraints Front Seats To move a manual seat forward or rearward: Seat Height Adjuster Manual Seats { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. 1. Lift the bar to unlock the seat. 2. Slide the seat to the desired position and release the bar.
Seats and Restraints Lumbar Seat Adjustment Reclining Seatbacks { CAUTION You can lose control of the vehicle if you try to adjust the seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. On seats with this feature, turn the knob clockwise or counterclockwise to increase or decrease the lumbar support.
1-4 Seats and Restraints Seatback Latches (Three Door Model) For easy entry/exit to the rear seats on three door models: { CAUTION If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. To return the seat to the upright position: To adjust a manual reclining seatback, turn the knob. Do not lean on the seatback while adjusting it. 1.
Seats and Restraints 1-5 Head Restraints The vehicle’s front seats have adjustable head restraints. { CAUTION With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head.
1-6 Seats and Restraints Heated Seats Active Head Restraint System On vehicles with heated front seats, the controls for each seat are located on the center of the instrument panel. To operate the heated seats the ignition must be on. M (Heated Seat): Press this button to turn on the heated seat. The vehicle has an active head restraint system in the front seating positions. These automatically tilt forward to reduce the risk of neck injury if the vehicle is hit from behind.
Seats and Restraints Rear Seats 1-7 To lower the seatback: CAUTION Rear Seat Operation { CAUTION If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. { CAUTION A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
1-8 Seats and Restraints To return the seat to the sitting position: 3. Push and pull on the seatback to make sure it is locked. 4. Remove the safety belt from the storage clip. The seatback must be locked or you will not be able to pull out and use the rear center safety belt. Always push and pull on the seatback to be sure it is locked. 1. Make sure the safety belt is through the storage clip. 2. Lift the seatback and push it rearward until it is locked in the sitting position.
Seats and Restraints { CAUTION It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 4-14.
1-10 Seats and Restraints Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield...
Seats and Restraints 1-11 Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. wearing a safety belt or not.
1-12 Seats and Restraints Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h).
Seats and Restraints If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash. { CAUTION { CAUTION You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
1-14 Seats and Restraints Q: What is wrong with this? { CAUTION Q: What is wrong with this? You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong buckle. A: The belt is over an armrest.
Seats and Restraints { CAUTION Q: What is wrong with this? You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
1-16 Seats and Restraints Q: What is wrong with this? A: The belt is behind the body. { CAUTION You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries.
Seats and Restraints 1-17 { CAUTION You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/ retailer to fix it. Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. Here is how to wear a lap-shoulder belt properly. 1. Adjust the seat so you can sit up straight. To see how, see “Seats” in the Index. 2.
1-18 Seats and Restraints Before you close a door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and the vehicle. 4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See “Shoulder Belt Height Adjustment” later in this section. 5. To make the lap part tight, pull up on the shoulder belt.
Seats and Restraints Safety Belt Pretensioners To move it, push the button on the front of the height adjuster and move the height adjuster to the desired position. After you move the adjuster to where you want it, try to move it down without pushing the button to make sure it has locked into position. The vehicle has safety belt pretensioners for the front outboard occupants. Although you cannot see them, they are part of the safety belt assembly.
1-20 Seats and Restraints { CAUTION 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest.
Seats and Restraints 1-21 To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide. Push the guide into the pocket on the side of seatback. Properly secure the guide loop before folding the seatback. The comfort guide and vehicle can be damaged while closing a door if it is not properly secured in its storage location. 4. Buckle, position, and release the safety belt as described previously in this section.
1-22 Seats and Restraints Safety Belt Extender Safety Belt Check Care of Safety Belts If the safety belt will fasten around you, you should use it. Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Seats and Restraints Replacing Safety Belt System Parts After a Crash { CAUTION A crash can damage the safety belt system in the vehicle. A damaged safety belt system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure the safety belt systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. After a minor crash, replacement of safety belts may not be necessary.
1-24 Seats and Restraints For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger. With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the seatback closest to the door. With roof-rail airbags, the word AIRBAG will appear along the headliner or trim. Airbags are designed to supplement the protection provided by safety belts.
Seats and Restraints { CAUTION Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with airbags.
1-26 Seats and Restraints { CAUTION Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door. The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows.
Seats and Restraints When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold. Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants.
1-28 Seats and Restraints Seat-mounted side impact and roof-rail airbags are not intended to inflate in frontal impacts, near-frontal impacts, rollovers, or rear impacts. A seat-mounted side impact airbag is intended to deploy on the side of the vehicle that is struck. A roof-rail airbag is intended to deploy on the side of the vehicle that is struck.
Seats and Restraints What Will You See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy. Some components of the airbag module may be hot for several minutes. For location of the airbag modules, see What Makes an Airbag Inflate? on page 1-28.
1-30 Seats and Restraints Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible in the rearview mirror when you start the vehicle. United States Canada The words ON and OFF, or the symbol for on and off, will be visible during the system check. When the system check is complete, either the word ON or the word OFF, or the symbol for on or the symbol for off, will be visible.
Seats and Restraints A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
1-32 Seats and Restraints When the passenger sensing system has turned off the right front passenger’s frontal airbag and seat-mounted side impact airbag, the off indicator will light and stay lit to remind you that the airbags are off. See Passenger Airbag Status Indicator on page 4-15. If a child restraint has been installed and the on indicator is lit, turn the vehicle off.
Seats and Restraints If a person of adult-size is sitting in the right front passenger’s seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat.
1-34 Seats and Restraints We recommend that you not use seat covers or other aftermarket equipment other than any that GM has approved for your specific vehicle. See Adding Equipment to Your Airbag-Equipped Vehicle on page 1-35 for more information about modifications that can affect how the system operates. The passenger sensing system may suppress the airbag deployment when liquid soaks into the seat.
Seats and Restraints Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
1-36 Seats and Restraints Airbag System Check The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 4-14 for more information. Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly. Do not open or break the airbag coverings. If there are any opened or broken airbag covers, have the airbag covering and/or airbag module replaced.
Seats and Restraints Child Restraints Older Children The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. • Buckle the lap-shoulder belt. Does the shoulder belt rest on the shoulder? If yes, continue.
1-38 Seats and Restraints { CAUTION { CAUTION Never do this. Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly.
Seats and Restraints { CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts. Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Children who are not restrained properly can strike other people, or can be thrown out of the vehicle.
1-40 Seats and Restraints For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. { CAUTION Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat.
Seats and Restraints { CAUTION To reduce the risk of neck and head injury during a crash, infants need complete support. This is because an infant’s neck is not fully developed and its head weighs so much compared with the rest of its body. In a crash, an infant in a rear-facing child restraint settles into the restraint, so the crash forces can be distributed across the strongest part of an infant’s body, the back and shoulders. Infants should always be secured in rear-facing child restraints.
1-42 Seats and Restraints Securing an Add-On Child Restraint in the Vehicle { CAUTION (B) Forward-Facing Child Seat (C) Booster Seats A forward-facing child seat (B) provides restraint for the child’s body with the harness. A booster seat (C) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
Seats and Restraints To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system. See Lower Anchors and Tethers for Children (LATCH) on page 1-45 for more information. A child can be endangered in a crash if the child restraint is not properly secured in the vehicle.
1-44 Seats and Restraints A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
Seats and Restraints Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
1-46 Seats and Restraints Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. Your child restraint may have a single tether (A) or a dual tether (C).
Seats and Restraints Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. There is no place to attach the top tether in this position. To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion.
1-48 Seats and Restraints Securing a Child Restraint Designed for the LATCH System { CAUTION If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual.
Seats and Restraints Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position. 1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts.
1-50 Seats and Restraints Replacing LATCH System Parts After a Crash { CAUTION If the position you are using has an adjustable headrest or head restraint and you are using a single tether, raise the headrest or head restraint and route the tether under the headrest or head restraint and in between the headrest or head restraint posts. 3. Push and pull the child restraint in different directions to be sure it is secure. A crash can damage the LATCH system in the vehicle.
Seats and Restraints Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
1-52 Seats and Restraints 6. If your child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-45 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5.
Seats and Restraints Securing Child Restraints (Right Front Seat) Your vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-43. In addition, your vehicle has a passenger sensing system which is designed to turn off the right front passenger’s frontal and seat-mounted side impact airbag under certain conditions.
1-54 Seats and Restraints Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. the vehicle. See Passenger Airbag Status Indicator on page 4-15. 2. Put the child restraint on the seat.
Seats and Restraints 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure.
1-56 Seats and Restraints ✍ NOTES
Keys, Doors and Windows Keys, Doors and Windows Theft-Deterrent Systems Keys Windows Keys ...................................2-2 Remote Keyless Entry (RKE) System ..........2-3 Remote Keyless Entry (RKE) System Operation ..........................2-4 Doors and Locks Door Locks .........................2-5 Power Door Locks ..............2-5 Rear Door Security Locks ...2-6 Liftgate ...............................2-6 Theft-Deterrent Systems .....2-7 Immobilizer .........................
2-2 Keys, Doors and Windows Keys { CAUTION Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window. Do not leave the keys in a vehicle with children.
Keys, Doors and Windows Keep this number in a safe place. If you lose your keys, you will be able to have one made easily using this number. If you need a new key, go to your dealer/retailer for the correct key code. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. If you are locked out of your vehicle, contact Roadside Assistance or OnStar. See Roadside Assistance Program on page 11-5 or OnStar® System on page 4-38.
2-4 Keys, Doors and Windows Remote Keyless Entry (RKE) System Operation c (Lock): Press to lock the doors, liftgate and fuel tank door. If the driver door is open, the doors will not lock. d (Unlock): Press to unlock the doors, liftgate and fuel tank door. Press and hold the windows. d to lower all Matching Transmitter(s) to Your Vehicle Each RKE transmitter is uniquely coded to prevent another transmitter from unlocking the vehicle.
Keys, Doors and Windows Doors and Locks Door Locks CAUTION (Continued) • Young children who get into { CAUTION Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive.
2-6 Keys, Doors and Windows Rear Door Security Locks Your vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside. To set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.
Keys, Doors and Windows 2-7 Theft-Deterrent Systems Notice: If you open the liftgate without checking for overhead obstructions such as a garage door, you could damage the liftgate or the liftgate glass. Always check to make sure the area above and behind the liftgate is clear before opening it. Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal.
2-8 Keys, Doors and Windows This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Keys, Doors and Windows Content Theft-Deterrent Arming the System This vehicle has a content theft-deterrent alarm system. To arm the system: 1. Close all doors, windows, hood and sunroof. 2. Press c on the Remote Keyless Entry (RKE) transmitter. The security light is located on the instrument panel. Do not use this system if there are people in the vehicle. The doors can not be unlocked from inside the vehicle.
2-10 Keys, Doors and Windows Windows Power Windows { CAUTION { CAUTION Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Keys, Doors and Windows Express-Down Window Window Lockout This feature is on all windows. It allows you to lower the window all the way without holding the switch down. o (Window Lockout): Press the front of the switch to the second position and release. If you want to stop the window as it is lowering, briefly pull up the switch. The window switches are located on each of the doors. To lower a window, press the switch down. To raise a window, pull the switch up.
2-12 Keys, Doors and Windows Mirrors Cleaning the Mirror Manual Rearview Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with glass cleaner. Hold the mirror in the center to move it for a clearer view of behind your vehicle. Headlamp Glare To reduce headlamp glare from vehicles following from behind, pull the lever toward you. Push the lever forward after the vehicle glare is gone, to return the mirror back to the original position.
Keys, Doors and Windows Outside Heated Mirrors Sunroof The vehicle may have outside heated mirrors which help clear the condensation, snow, and ice. < (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under, Climate Control System on page 7-1 for more information. 2-13 t Vent/Open: With the sunroof in the closed position, press to vent the sunroof. With the sunroof in the vent position, press to open the sunroof. The sunshade will open automatically with the sunroof.
2-14 Keys, Doors and Windows ✍ NOTES
Storage Storage Storage Glove Box ..........................3-1 Cupholders .........................3-1 Cargo Cover .......................3-1 Cargo Tie Downs ...............3-1 Storage Cargo Cover Glove Box Your vehicle may have a cargo cover. Pull up on the handle to open the glovebox. There may be a shelf inside that can be removed by lifting up on the shelf and pulling it out.
3-2 Storage ✍ NOTES
Instruments and Controls Instruments and Controls Instrument Panel Overview Instrument Panel Overview ...........................4-2 Hazard Warning Flashers ...4-4 Horn ...................................4-4 Tilt Wheel ...........................4-4 Turn Signal/Multifunction Lever ................................4-4 Cruise Control ....................4-5 Turn and Lane-Change Signals .............................4-8 Headlamp High/Low-Beam Changer ............................4-8 Flash-to-Pass ...............
4-2 Instruments and Controls Instrument Panel Overview
Instruments and Controls The main components of the instrument panel are the: A. Exterior Lamps Controls on page 5-1. B. Outlets. Outlet Adjustment on page 7-4. C. Turn Signal/Multifunction Lever on page 4-4. D. DIC Operation and Displays (Base Level DIC and Audio) on page 4-27 or DIC Operation and Displays (Uplevel DIC and Audio) on page 4-31 and Audio Steering Wheel Controls on page 6-24. (If Equipped) E. Instrument Panel Cluster on page 4-12. F. Audio Steering Wheel Controls on page 6-24.
4-4 Instruments and Controls Hazard Warning Flashers Tilt Wheel | : Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press the button again to turn the flashers off. A tilt and telescope wheel lets the steering wheel position be adjusted. Turn Signal/Multifunction Lever While the hazard warning flashers are on, the turn signals do not work.
Instruments and Controls Cruise Control { CAUTION Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.
4-6 Instruments and Controls Setting Cruise Control 1. Press J and the current speed is stored and maintained. For safety reasons the cruise control cannot be turned on until the brake has been applied once. 2. Take your foot off the accelerator pedal. The J indicator light on the instrument panel cluster turns on after the cruise control has been set to the desired speed. With automatic transmission, only use cruise control in DRIVE (D). Press the On/Off button to turn on the cruise control.
Instruments and Controls Resuming a Set Speed Once the vehicle speed reaches about 25 mph (40 km/h) or more and the cruise control is on, press W. The vehicle returns to the previous speed selected before the cruise was disengaged. The stored speed is deleted if the ignition is turned off. Increasing Speed While Using Cruise Control • Press and hold J until the desired speed is reached, then release it. • To increase vehicle speed in small increments, briefly press J repeatedly.
4-8 Instruments and Controls Turn and Lane-Change Signals The turn signal has two upward and downward positions to signal a turn or a lane change. To signal a lane change, raise or lower the lever until the arrow starts to flash, and then release the lever. Do not move the lever past the detent. The turn signal will automatically flash three times and turn off. To cancel it before turning, move the lever slightly in either direction. Do not past the detent.
Instruments and Controls Windshield Wipers For a single wipe pull the lever down from the off position. The lever will return to its original position. For more cycles, hold the lever down before releasing it. Clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, gently loosen or thaw them. If the blades do become damaged, install new blades or blade inserts. See Windshield Wiper Blade Replacement on page 9-21.
4-10 Instruments and Controls Windshield Washer { CAUTION In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Pull the windshield wiper lever toward you to spray washer fluid on the windshield. The wipers will run for a few cycles to clear the windshield. For more wash cycles, pull the lever forward and hold.
Instruments and Controls Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty.
4-12 Instruments and Controls Instrument Panel Cluster The instrument cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Instruments and Controls Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) or kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles or kilometers. If your vehicle needs a new odometer installed, the new one will be set to the mileage total of the old odometer. If it cannot, it will be set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed.
4-14 Instruments and Controls Safety Belt Reminders Driver Safety Belt Reminder Light There is a Driver Safety Belt Reminder Light on the instrument panel cluster. When the engine is started this light and chime will come on and stay on for several seconds to remind people to fasten their safety belts. The light will also begin to flash. This cycle repeats if the driver remains unbuckled and the vehicle is moving. If the driver’s belt is already buckled, neither the light nor chime will come on.
Instruments and Controls If the airbag readiness light stays on after you start the vehicle or comes on when your are driving, your airbag system may not work properly. Have your vehicle serviced right away. { CAUTION If the airbag readiness light stays on after the vehicle is started, it means the airbag system may not be working properly. The airbags in the vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.
4-16 Instruments and Controls If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag and seat-mounted side impact airbag are enabled (may inflate). { CAUTION If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped).
Instruments and Controls If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { CAUTION If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system.
4-18 Instruments and Controls If the light comes on while driving, a chime will sound. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 9-72. { CAUTION The brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident.
Instruments and Controls StabiliTrak® Indicator Light When the system is active, the light will flash while the system helps control the vehicle. You may also feel or hear the system working. This is normal. Engine Coolant Temperature Warning Light For vehicles with this light, it should come on briefly when the ignition is turned on. If the light does not come on, have it fixed so it will be ready to warn if there is a problem.
4-20 Instruments and Controls Stop and check the tires as soon as it is safe to do so. If underinflated, inflate to the proper pressure. See Tires on page 9-38 for more information. This light flashes for approximately one minute and then stays on when the system detects a malfunction. See Tire Pressure Monitor System on page 9-48 for more information.
Instruments and Controls This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. The following can prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. If the light continues to flash, when it is safe to do so, stop the vehicle.
4-22 Instruments and Controls Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not pass this inspection if the check engine light is on or not working properly.
Instruments and Controls Low Oil Level Light This light should come on briefly when the ignition is turned on as a check to let you know that the light is working. If this light comes on and stays on while the engine is running, it means your engine is low on oil. You need to check the oil level as soon as possible. See Engine Oil on page 9-7 for further information. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by the vehicle warranty.
4-24 Instruments and Controls Exterior Lamps Off Reminder This light comes on whenever the exterior lights are off. See Exterior Lamps Controls on page 5-1 for more information. Cruise Control Light Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 4-8 for more information.
Instruments and Controls Fuel Gage The arrow on the fuel gage points to the side of the vehicle with the fuel door. 4-25 Low Fuel Warning Light Here are five things that some owners ask about. These are normal and do not indicate a problem with your fuel gage: Your fuel gage tells you about how much fuel you have left, when the ignition is on. When the indicator nears empty, the low fuel warning light will come on. You still have a little fuel left, but you should get more soon.
4-26 Instruments and Controls Driver Information Center (DIC) Vehicles with a Driver Information Center (DIC) can display: • Time • Outside temperature • Date or audio system, if it is turned on • Trip computer, on vehicles with this feature • Warning messages The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer and audio system.
Instruments and Controls 4-27 DIC Operation and Displays (Base Level DIC and Audio) On some vehicles, menu options can be selected with the left thumbwheel on the steering wheel: CD 30 with MP3 Player shown, without MP3 Player similar If the vehicle has the base level DIC, the following information explains how the system works. Selecting Functions Functions and settings of some equipment can be accessed through the DIC.
4-28 Instruments and Controls On some vehicles, if a warning message appears, the display is blocked from other functions. See DIC Warnings and Messages (Base and Uplevel Systems) on page 4-37 for information on acknowledging the message. System Settings To enter the Settings menu: 1. Press SETTINGS on the audio system. Audio or System will appear. 2. Press the left arrow button on the audio system or use the thumbwheel on the steering wheel, if the vehicle has one, to reach menu item System.
Instruments and Controls Trip Computer The vehicle may have a trip computer. The trip computer provides information on driving data. This information is continually recorded and evaluated electronically. If power has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
4-30 Instruments and Controls Average Speed Range This display shows the average speed of the vehicle in miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The measurement can be reset to zero at any time and restarted. See “Reset” later in this section.
Instruments and Controls 4-31 DIC Operation and Displays (Uplevel DIC and Audio) Reset The following trip computer information can be reset: • • • • Average consumption Trip consumption Average speed Distance travelled To reset the value: 1. Select the desired trip computer information. 2. Press the OK button on the audio system, or press the left thumbwheel, if your vehicle has this feature, on the steering wheel: • To reset the current value, press and hold briefly.
4-32 Instruments and Controls On some vehicles, if a warning message appears, the display is blocked from other functions. See DIC Warnings and Messages (Base and Uplevel Systems) on page 4-37 for information on acknowledging the message.
Instruments and Controls 4-33 System Settings Setting Date and Time Setting Units of Measure To enter the Settings menu, do one of the following: To set the date and time: To select which units of measure are to be used: • Press MAIN, if your vehicle has this feature, on the audio system. • Press the SETTINGS button on the audio system. 1. Select Time, Date from the Settings menu. The menu for Time, Date is displayed. 2. Select the menu items required. The Settings menu will appear. 3.
4-34 Instruments and Controls Day / Night Trip Computer The vehicle may have this feature. The display can be adjusted to best match the lighting conditions. To adjust this setting: The vehicle may have a trip computer. The trip computer provides information on driving data. This information is continually recorded and evaluated electronically. If power has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. 1.
Instruments and Controls For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. Fuel range cannot be reset.
4-36 Instruments and Controls Average Consumption This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (l/100 km). This number is calculated based on the number of mpg (l/100 km) recorded since the last time this menu item was reset. The measurement can be reset to zero at any time and restarted. See “Reset” later in this section. Timer This display can be used as a timer. Select Timer from the menu. The Timer menu will display. To start the timer, select Start.
Instruments and Controls DIC Warnings and Messages (Base and Uplevel Systems) Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
4-38 Instruments and Controls Brakelight switch check Safeguard check This message displays when the brake lamp does not come on when the brake is applied. Have your vehicle serviced by your dealer/retailer immediately. This message displays when there is a problem with the theft-deterrent system. Have the system serviced by your dealer/retailer immediately. Coolant level check This message displays when the engine coolant level is low.
Instruments and Controls OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.
4-40 Instruments and Controls Available Services included with Directions & Connections Plan • All Safe and Sound Plan Services • Driving Directions - Advisor delivered or OnStar Turn-by-Turn Navigation (If equipped) • RideAssist • Information and Convenience Services OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands.
Instruments and Controls OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service.
4-42 Instruments and Controls ✍ NOTES
Lighting Lighting Lighting Exterior Lamps Controls .....5-1 Daytime Running Lamps (DRL) ....................5-2 Delayed Headlamps ............5-2 Fog Lamps .........................5-2 Instrument Panel Brightness .........................5-3 Dome Lamp(s) ....................5-3 Entry Lighting .....................5-3 Reading Lamps ..................5-3 Rear Compartment Lamp .....5-4 Battery Run-Down Protection .........................
5-2 Lighting Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada.
Lighting Instrument Panel Brightness D (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control to the left of the steering wheel. Push the knob in all the way until it extends out and then turn the knob clockwise or counterclockwise to brighten or dim the lights. Push the knob back in when finished. Dome Lamp(s) There are two dome lamps. The rear dome lamp turns on automatically with the front dome lamp.
5-4 Lighting Rear Reading Lamps The rear seat reading lamps can be turned on while the ignition is on. 9 R (Off): Press to turn the lamp off. (On): Press to turn the lamp on. Rear Compartment Lamp The liftgate lamp turns on when the liftgate is opened and turns off when the liftgate is closed. Battery Run-Down Protection This feature helps prevent the battery from being drained, if the courtesy lamps, reading lamps, sun visor, glovebox or rear compartment lamp are left on.
Infotainment Infotainment Audio System(s) Audio System(s) Determine which audio system the vehicle has and then read the following pages to become familiar with its features. Audio System(s) .................6-1 Radio(s) .............................6-2 Theft-Deterrent Feature .....6-24 Audio Steering Wheel Controls ..........................6-24 Radio Reception ...............6-25 Fixed Mast Antenna ..........
6-2 Infotainment Radio(s) Ignition Logic When this feature is enabled it turns the audio system on or off when the ignition is turned on or off. To turn the audio system on or off with Ignition Logic: • Press n / R or insert a CD to turn the audio system on. Press n / R to turn the audio system off when the Ignition Logic system is disabled and the ignition is ON/RUN. CD 30 MP3 Shown, CD 30 Similar System Operation n / R (Volume/Power): Press to turn the system on or off.
Infotainment The Ignition Logic is preset to turn off the audio system when the ignition is turned off. To enable or disable Ignition Logic: 1. Press SETTINGS until Audio displays. 2. Press \ until System displays. 3. Press OK until Ign. Logic ON or Ign. Logic OFF displays. 4. Press \ or ] to select the setting. The setting is saved automatically. • Press SETTINGS again to move back one level in the menu. • Press FM/AM, CD/MP3, or BC to turn on that feature.
6-4 Infotainment Audio displays and the audio system starts to play if SETTINGS, FM/AM, CD/MP3, or BC is not pressed within five seconds after the setting is saved. To adjust the Treble: 1. Press SOUND until Treble appears. 2. Press \ or ] to adjust the level from -12 through +12. The setting is saved automatically. • Press SETTINGS again to go back one level in the menu. • Press FM/AM, CD/MP3, or BC to display that function.
Infotainment Adjusting the Speakers (Balance/Fade) To adjust the Balance using the SOUND button: 1. Press SOUND until Balance appears. 2. Press \ or ] to adjust the level from -12 through +12. The setting is saved automatically. • Press SETTINGS again to go back one level in the menu. • Press FM/AM, CD/MP3, or BC to display that function. To adjust the Balance using the SETTINGS button: 1. Press SETTINGS until Audio appears. 2. Press OK until Balance appears. 3.
6-6 Infotainment OnStar® Volume On Volume Using the Radio For vehicles with OnStar, the OnStar Volume is used to set the maximum initial volume level for the OnStar system when it is turned on. The On Volume is used to set the maximum initial volume level for the audio system when it is turned on. FM/AM: Press to select between FM, FM-AS, AM, and AM-AS, or to listen to the radio while a CD is playing. To set OnStar Volume: 1. Press SETTINGS until Audio appears. 2. Press OK until OnStar Vol. appears.
Infotainment Finding an FM/AM Station 1 - 9 (Station Preset Buttons): Press to play stations that are programmed to the radio preset pushbuttons. SCN (Station Preset Scan): Press to start station preset scan. The radio goes to the first preset station, plays for a few seconds, then goes to the next preset station. Press SCN again to stop scanning preset stations. \ or ]: Press to find radio stations using the automatic station search or the manual station search.
6-8 Infotainment Radio stations can be stored manually, and by using Autostore. Using the CD Player Loading a CD Display Options To manually store preset stations: The display can be changed depending on what type of CD is in the CD player. The display options are: To load a CD, insert the CD label side up in the CD player. The CD player pulls the CD in automatically. 1. Select FM or AM and tune to the desired radio station. 2.
Infotainment Random: Press CD/MP3 three times to hear the tracks in random, rather than sequential order. Press \ or ] to select between Random on and Random off. RDM shows on the display when random is in use. MP3 CDs recorded without ID3 tags display: Using an MP3 CD MP3 CDs recorded with ID3 tags display: The CD 30 MP3 is capable of playing MP3 CDs that have been recorded to a CD-R. Supported File Structure The CD 30 MP3 supports up to: • 99 albums. • 367 tracks. • Bit rates up to 256 kbps.
6-10 Infotainment Random Mode MP3 CD can be played in the following random modes: • Random album: Tracks from the selected album are played randomly. • Random CD: All tracks from all albums are played randomly. • Random Off: Turns off random play. To use random: 1. Press CD/MP3 three times. 2. Press \ or ] to select between Random album, Random CD and Random Off. RDM shows on the display when random is use.
Infotainment 6-11 Ignition Logic When this feature is enabled it turns the audio system on or off when the ignition is turned on or off. To turn the audio system on or off with the Ignition Logic: • Press R or Z to turn the audio CDC 40 System Operation R (Volume/Power): Press to turn the system on or off. Turn to increase or decrease the volume. BC (Board Computer): Press to use the Board Computer, see DIC Warnings and Messages (Base and Uplevel Systems) on page 4-37.
6-12 Infotainment The Ignition Logic is preset to turn off the audio system when the ignition is turned off. To enable or disable Ignition Logic: 1. Press SETTINGS, System Settings displays. 2. Turn the multifunction knob to select Ign. Logic and press the multifunction knob to select or un-select the option. System Display The following information shows on the system display: • FM or AM displays, and the current station frequency or station name if the radio is active.
Infotainment 6-13 Menus To exit from a menu: Selecting from a List The menus of the audio systems are structured in levels. The current menu level is indicated by vertical lines at the edge of the screen. • Turn the multifunction knob to Some menus are displayed in the form of lists. Selecting from a Menu The items within a menu are selected by turning the multifunction knob to move the cursor. The cursor highlights the menu item being selected. To select a menu item: 1.
6-14 Infotainment Overlay Menus Additional notes and information on the audio system or other vehicle components may appear on the display as an overlay in some cases. The current menu is overlaid with the information box. Some settings have to be confirmed, others are automatically enabled after a short time. 3. Select Bass from the menu and turn the multifunction knob to adjust the level. 4. Press the multifunction knob to save the setting.
Infotainment Adjusting the Sound Settings There are preset sound settings designed for different types of music. To adjust the sound settings: 1. Press SOUND and select the Sound menu item. 2. Select Sound. 3. Select: User, Jazz, Speech, Pop, Classical, and Rock. 4. Press the multifunction knob to save the setting. Adjusting the Speakers (Balance/Fade) 3. Select Balance from the menu and turn the multifunction knob to adjust the level. 4. Press the multifunction knob to save the setting.
6-16 Infotainment Speed-Dependant Volume Control (SDVC) SDVC automatically adjusts the volume for road and wind noise as the vehicle increases or decreases speed while driving. To adjust SDVC: 1. Press SOUND, then SETTINGS and select Volume from the menu. 2. Select SDVC. 3. Turn the multifunction knob to adjust the level. 4. Press the multifunction knob to save the setting.
Infotainment Using the Radio Finding an FM/AM Station FM/AM: Press to select between FM, FM-AS, AM, and AM-AS, or to listen to the radio while a CD is playing. The Tuner Menu displays. 1 - 9 (Station Preset Buttons): Press to play stations that are programmed to the radio preset pushbuttons. LOC (LOCAL/DX Function): Press to change between LOC ON or LOC OFF. When the LOC function is on, it searches for the strongest radio frequency.
6-18 Infotainment Setting Preset Stations The radio can store up to 36 stations using the station preset buttons: • • • • 9 FM 9 FM - AS (Autostore) 9 AM 9 AM - AS (Autostore) Radio stations can be stored using the station preset buttons, the multifunction knob, and by using Autostore. To manually store stations using the station preset buttons: 1. Select FM or AM and tune to the desired radio station. 2.
Infotainment 6-19 Display Options Selecting a Track Searching Within a Track The display can be changed depending on what type of CD is in the CD player. The display options are: Tracks can be selected using the four-way switch or the CD menu functions. To search within a track using the four-way switch or the CD menu functions: Selecting a track using the four-way switch: To search using the four-way switch: \ or ]: Press to go to the next or previous track within a CD. 1.
6-20 Infotainment Selecting CD To turn off random: Repeat Track CDs can be selected by: 1. Select Extras from the CD menu. • Pressing the appropriate station 2. Select Normal, and disappears. The Repeat function repeats the current track. The function can be enabled and disabled by using the four-way switch or the CD menu. preset button. • Pressing _ or ^ on the four-way T • Using the CD menu function.
Infotainment Scan CD The Scan CD function scans the first ten seconds of each track on the current CD. The function can be enabled and disabled by using the four-way switch or the CD menu. To use Scan CD using the four-way switch: 1. Press and hold _ until u appears on the display. 2. Press and hold ^ until u is no longer on the display to turn off repeat track. To use Scan CD using the CD menu: 1. Select Extras from the CD menu. 2. Select Scan CD, on the display.
6-22 Infotainment Playing an MP3 or Mixed Mode CD Selecting a track using the CD menu and the Track function: Selecting an MP3 or Mixed Mode Album CDC: Press to play an MP3 CD that is already loaded into the CD player while the radio is playing. The CD Menu displays. 1. Select Track from the CD menu. CDs can be selected by: 2. Select the desired track from the menu.
Infotainment Tracks play in the following order for Random play CD: Tracks play in the following order for Random magazine: Care of CD’s and the CD Player • MP3 CD: If there are five or • MP3 CD: If there are five or Care of CDs fewer albums on an MP3 CD, four tracks per album are played in random order. If there are more than five albums on the MP3 CD, one track is played per album. Tracks from the selected album are played randomly.
6-24 Infotainment Care of the CD Player Do not add labels to a CD, it could get caught in the CD player. Use a marking pen to write on the top of the CD if a description is needed. Audio Steering Wheel Controls Z (Rotary Control): Manually seek a station by turning to move the cursor either to the previous or next screen entry. Press to confirm the selection. Do not use CD lens cleaners, they could damage the CD player.
Infotainment X : Press to toggle between the radio and CD or MP3 as an active source for playback. ^ / _: Press the arrows to go back or advance to the previous or next preset station if playing the radio. Press and hold to scroll through the preset stations. Press to go back or advance one track at a time on a CD. Press to quickly reverse or advance through the tracks within a CD. 3 (volume): Turn the rotary control to adjust the volume. Press and hold to adjust the volume continuously.
6-26 Infotainment ✍ NOTES
Climate Controls Climate Controls 7-1 Climate Controls Climate Control System Climate Controls Climate Control System ......7-1 Outlet Adjustment ...............7-4 The heating, cooling, and ventilation for the vehicle can be controlled with this system. Operation Air Delivery Mode Knob The air delivery mode or fan speed can be manually adjusted.
7-2 Climate Controls Y (Vent): This mode directs air to the instrument panel outlets. X (Defog): This mode directs air to the windshield and front door windows. To reduce fogging, press # to turn on the air conditioner. The fan must also be on. W (Defog/Floor): This mode directs air to the windshield, front door windows, and floor outlets. To reduce fogging, press # to turn on the air conditioner. The fan must also be on. [ (Floor): This mode directs most of the air to the floor outlets.
Climate Controls For quicker cool down, do the following: 1. Press # to turn on the air conditioning. 2. Select Y mode. 3. Set the temperature knob to the coldest temperature. 4. Set the fan knob to 4. 5. Open all vents. Recirculation ^ (Recirculation): Press to turn the recirculation mode on or off. An indicator light inside the button comes on when the recirculation mode is active. This mode recirculates air inside the passenger compartment and prevents outside air from entering the vehicle.
7-4 Climate Controls Outlet Adjustment Use the thumbwheel below the air outlets to change the direction of the air flow. Use the vertical thumbwheel next to the outlets to control the amount of air flow or to shut off the airflow completely. Keep all outlets open whenever possible for best system performance. Operation Tips • Clear away any ice, snow, or leaves from the air inlets at the base of the windshield that can block the flow of air into the vehicle.
Driving and Operating Driving and Operating Starting and Operating Your Vehicle New Vehicle Break-In .........8-2 Ignition Positions ................8-2 Retained Accessory Power (RAP) .....................8-3 Starting the Engine .............8-3 Engine Heater ....................8-4 Automatic Transmission Operation ..........................8-5 Manual Transmission Operation ..........................8-9 Parking Brake ...................8-10 Shifting Into Park ..............8-11 Shifting Out of Park .......
8-2 Driving and Operating Starting and Operating Your Vehicle Following break-in, engine speed and load can be gradually increased. Ignition Positions New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: constant speed, fast or slow, for the first 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake or slow the vehicle. the first 200 miles (322 km) or so.
Driving and Operating B (STEERING UNLOCKED/ IGNITION OFF): This position unlocks the steering wheel. C (ON/RUN): The ignition switch stays in this position when the engine is running. This position can be used to operate the electrical accessories, as well as to display some warning and indicator lights. The battery could be drained if you leave the key in the ON/RUN position with the engine off. You may not be able to start the vehicle if the battery is allowed to drain for an extended period of time.
8-4 Driving and Operating Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START for many seconds, cranking will be stopped after 15 seconds to prevent cranking motor damage.
Driving and Operating To Use the Engine Heater 1. Turn off the engine. { CAUTION 8-5 Automatic Transmission Operation Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 2.
8-6 Driving and Operating PARK (P): This position locks the front wheels. It is the best position to use when the engine is started because your vehicle cannot move easily. { CAUTION It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Driving and Operating Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle. THIRD (3): This position is also used for normal driving, however, it offers more power and lower fuel economy than DRIVE (D).
8-8 Driving and Operating Winter Driving Mode This feature helps you accelerate in slippery driving conditions by using THIRD (3) gear when you begin to accelerate from a stopped position. The Winter Driving Mode is turned off by one of the following: • Pressing the winter driving mode button again. • Manually shifting to SECOND (2) or FIRST (1) gear. • Turning off the ignition.
Driving and Operating When you release the brake with the transmission in gear, you may feel the transmission shift from Neutral to Drive automatically. You may also feel the transmission shift from Drive to Neutral when the brake is applied. This is normal operation of the automatic transmission. Manual Transmission Operation Five-Speed Downhill Grade Assist When traveling down steep grades your transmission may automatically downshift into a lower gear when the brake is applied.
8-10 Driving and Operating If reverse gear does not engage, set the selector lever in neutral, and release the clutch pedal. Press the clutch pedal again and repeat the gear selection. not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. Parking Brake Also, use REVERSE (R), along with the parking brake, to park your vehicle. Shift Speeds { CAUTION If you skip a gear when you downshift, you could lose control of your vehicle.
Driving and Operating A warning chime will sound and a brake warning light located on the instrument panel cluster will come on, if the parking brake is set, the ignition is on and the vehicle speed is greater than 5 mph (8 km/h). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.
8-12 Driving and Operating Leaving Your Vehicle with the Engine Running { CAUTION It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave the vehicle with the engine running.
Driving and Operating Shifting Out of Park This vehicle has an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shift lever is in PARK (P) with the shift lever button fully released. • Prevent movement of the shift lever out of PARK (P), unless the ignition is in the ON/RUN position and the regular brake pedal is applied.
8-14 Driving and Operating Engine Exhaust CAUTION { CAUTION Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • The exhaust system sounds strange or different. • Your vehicle gets rusty underneath. • Your vehicle was damaged in a collision. (Continued) (Continued) • Your vehicle was damaged • • when driving over high points on the road or over road debris.
Driving and Operating CAUTION (Continued) Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Also see “If You Are Caught in a Blizzard” under Winter Driving on page 8-27.
8-16 Driving and Operating Driving Your Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 1-8. { CAUTION Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: • Allow enough following distance between you and the driver in front of you.
Driving and Operating Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person’s chance of being killed or permanently disabled is higher than if the person had not been drinking. Braking Control of a Vehicle Average reaction time is about three-fourths of a second. But that is only an average.
8-18 Driving and Operating If your vehicle’s engine ever stops while you are driving, brake normally but do not pump the brakes. If you do, the pedal could get harder to push down. If the engine stops, you will still have some power brake assist. But you will use it when you brake. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push. Adding non-dealer/non-retailer accessories can affect your vehicle’s performance.
Driving and Operating Remember: ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let antilock work for you.
8-20 Driving and Operating It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if your vehicle is stuck in sand, mud, ice or snow, and you want to “rock” your vehicle to attempt to free it. It may also be necessary to turn off the system when driving in extreme off-road conditions where high wheel spin is required. See If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 8-29.
Driving and Operating Steering Tips It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves. The traction of the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels.
8-22 Driving and Operating Steering in Emergencies Off-Road Recovery There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking — if you can stop in time. But sometimes you cannot; there is not room. That is the time for evasive action — steering around the problem.
Driving and Operating Turn the steering wheel 3 to 5 inches (about one-eighth turn) until the right front tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway. Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait.
8-24 Driving and Operating If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready for a second skid if it occurs. slippery until your vehicle is skidding. Learn to recognize warning clues — such as enough water, ice, or packed snow on the road to make a mirrored surface — and slow down when you have any doubt.
Driving and Operating Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water. { CAUTION Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. You could lose control of the vehicle.
8-26 Driving and Operating Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing.
Driving and Operating { CAUTION Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have the engine running and the vehicle in gear when going downhill. • Stay in your own lane. Do not swing wide or cut across the center of the road. Drive at speeds that let you stay in your own lane.
8-28 Driving and Operating You can get wet ice when it is about freezing, 32°F (0°C), and freezing rain begins to fall. Try to avoid driving on wet ice until salt and sand crews can get there. than you would on dry pavement. See Antilock Brake System (ABS) on page 8-18. Whatever the condition — smooth ice, packed, blowing, or loose snow — drive with caution. • Watch for slippery spots. The Accelerate gently. Try not to break the fragile traction.
Driving and Operating { CAUTION Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. And check around again from time to time to be sure snow does not collect there.
8-30 Driving and Operating Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any stability system. See StabiliTrak® System on page 8-19. Then shift back and forth between REVERSE (R) and a forward gear, or with a manual transmission, between FIRST (1) or SECOND (2) and REVERSE (R), spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears.
Driving and Operating { CAUTION Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle.
8-32 Driving and Operating Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Driving and Operating 8-33 vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed the vehicle’s capacity weight. Certification Label Example 2 A. Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 150 lbs (68 kg) × 5 = 750 lbs (340 kg). C. Available Cargo Weight = 250 lbs (113 kg). Example 3 A. Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg). B.
8-34 Driving and Operating The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. And, if you do have a heavy load, you should spread it out. See “Steps for Determining Correct Load Limit” earlier in this section. { CAUTION Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Driving and Operating Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock.
8-36 Driving and Operating Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations.
Driving and Operating Filling the Tank { CAUTION { CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling your vehicle.
8-38 Driving and Operating When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 4-20. { CAUTION If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant.
Vehicle Service and Care Vehicle Service and Care Service Service ...............................9-2 Accessories and Modifications .....................9-3 California Proposition 65 Warning ............................9-3 California Perchlorate Materials Requirements .....9-3 Doing Your Own Service Work ....................9-4 Adding Equipment to the Outside of the Vehicle ......9-4 Owner Checks Owner Checks ....................9-5 Hood Release .....................9-5 Engine Compartment Overview ........
9-2 Vehicle Service and Care Buying New Tires .............9-54 Different Size Tires and Wheels .....................9-55 Uniform Tire Quality Grading ...........................9-56 Wheel Alignment and Tire Balance ....................9-58 Wheel Replacement ..........9-58 Tire Chains .......................9-59 Tire Changing If a Tire Goes Flat ............9-60 Changing a Flat Tire .........9-60 Removing the Spare Tire and Tools .................
Vehicle Service and Care Accessories and Modifications When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control and stability control. Some of these accessories could even cause malfunction or damage not covered by warranty.
9-4 Vehicle Service and Care Doing Your Own Service Work { CAUTION You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task. • Be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused.
Vehicle Service and Care Owner Checks 9-5 Hood Release To open the hood: { CAUTION An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. 2. Push the secondary hood release lever upward. { CAUTION Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber.
9-6 Vehicle Service and Care Engine Compartment Overview When you open the hood, this is what you will see:
Vehicle Service and Care A. Engine Air Cleaner/Filter on page 9-11. B. Engine Oil Fill Cap. Engine Oil on page 9-7. C. Brake Fluid Reservoir. Brakes on page 9-22. D. Coolant Reservoir. Cooling System on page 9-16. E. Coolant Reservoir Pressure Cap. Pressure Cap on page 9-15. F. Engine Compartment Fuse Block on page 9-34. G. Battery on page 9-25. H. Windshield Washer Fluid on page 9-20. I. Engine Oil Dipstick. Engine Oil on page 9-7.
9-8 Vehicle Service and Care When to Add Engine Oil What Kind of Engine Oil to Use If the oil is below the MIN (minimum) mark, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 10-2. Look for three things: Notice: Do not add too much oil.
Vehicle Service and Care • American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol.
9-10 Vehicle Service and Care How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to the letters InSP appearing in the odometer display, reset the system. After changing the engine oil, reset the system: 1. Turn the ignition key to LOCK/OFF. 2.
Vehicle Service and Care Engine Air Cleaner/Filter more information. If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. See Engine Compartment Overview on page 9-6 for the location of the engine air cleaner/filter.
9-12 Vehicle Service and Care Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take your vehicle to the dealer/retailer service department and have it repaired as soon as possible. Change the fluid and filter at the intervals listed in the Maintenance Schedule. See “Additional Required Services” in Service and Maintenance.
Vehicle Service and Care A 50/50 mixture of clean, drinkable water and DEX-COOL® coolant will: • Give freezing protection down to −34°F (−37°C). • Give boiling protection up to 265°F (129°C). • Protect against rust and corrosion. What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. { CAUTION • Help keep the proper engine temperature.
9-14 Vehicle Service and Care Checking Coolant { CAUTION Turning the coolant reservoir pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the coolant reservoir pressure cap - even a little - when the engine and radiator are hot. The coolant reservoir is located in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 9-6 for more information on location.
Vehicle Service and Care Pressure Cap Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. See Engine Compartment Overview on page 9-6 for more information on location. Engine Overheating There is an engine coolant temperature warning light on your vehicle’s instrument panel. See Engine Coolant Temperature Warning Light on page 4-19 for more information.
9-16 Vehicle Service and Care If you get the engine coolant temperature warning with no sign of steam, try this for a minute or so: 1. If your air conditioner is on, turn it off. 2. In heavy traffic, let the engine idle in N (NEUTRAL) while stopped. If it is safe to do so, pull off the road, shift to P (PARK) or N (NEUTRAL) and let the engine idle. 3. Turn on your heater to full hot at the highest fan speed and open the windows as necessary. If you no longer have the overheat warning, you can drive.
Vehicle Service and Care { CAUTION { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. If the coolant inside the coolant reservoir is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface.
9-18 Vehicle Service and Care How to Add Coolant to the Coolant Reservoir Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If you have not found a problem yet, check to see if coolant is visible in the coolant reservoir.
Vehicle Service and Care { CAUTION You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. Remove the coolant reservoir pressure cap when the cooling system, including the coolant reservoir pressure cap and upper radiator hose, is no longer hot. Turn the coolant reservoir pressure cap slowly counterclockwise about two or two and one-half turns.
9-20 Vehicle Service and Care Power Steering Fluid Windshield Washer Fluid When to Check Power Steering Fluid What to Use It is not necessary to check the power steering fluid level. A power steering fluid leak is the only reason for fluid loss. If a leak occurs, take your vehicle to the dealer/retailer service department and have it repaired as soon as possible. When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use.
Vehicle Service and Care Windshield Wiper Blade Replacement 9-21 Rear Windshield Wiper Front Windshield Wiper Windshield wiper blades should be inspected for wear or cracking. See “Maintenance Replacement Parts” in the Limited Warranty, Maintenance and owner Assistance Information manual for the proper type and length. Raise the wiper arm, tilt the wiper blade at a 90° angle to the wiper arm, and remove to the side. 1. Turn the ignition off. 2.
9-22 Vehicle Service and Care Brakes Brake Fluid The brake master cylinder and, on manual transmission vehicles, the clutch hydraulic system use the same reservoir. The reservoir is filled with DOT-4 brake fluid. See Engine Compartment Overview on page 9-6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear.
Vehicle Service and Care Required Services” in the Limited Warranty, Maintenance and Owner Assistance Information manual. Use new brake fluid from a sealed container only. See “Recommended Fluids and Lubricants” in the Limited Warranty, Maintenance and Owner Assistance Information manual. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
9-24 Vehicle Service and Care Rear disc brake pads do not have built-in brake pad wear indicators. Periodic visual inspection of the rear brake pads is required to determine when to replace the pads. Visually inspect the rear brake pads whenever the rear wheels are removed such as during tire rotation. Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. 1.
Vehicle Service and Care Replacing Brake System Parts Battery The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality brake parts. When you replace parts of the braking system — for example, when the brake linings wear down and you need new ones put in — be sure you get new approved replacement parts. If you do not, the brakes might not work properly.
9-26 Vehicle Service and Care Headlamp Aiming The optical headlamp aiming system has been preset at the factory and should need no further adjustment. However, If the vehicle is damaged in a crash, the headlamp aim may be affected and adjustment may be necessary. If oncoming vehicles flash their high beams at you, this may also mean the vertical aim needs to be adjusted. It is recommended that the vehicle is taken to your dealer/retailer for service if the headlamps need to be re-aimed.
Vehicle Service and Care 3. Record the distance from the ground to the aim dot on the low-beam headlamp. 4. At a wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in Step 4. 9-27 Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp. 6.
9-28 Vehicle Service and Care Bulb Replacement Front Turn Signal Lamps For the proper type of replacement bulbs, see Replacement Bulbs on page 9-33. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs 9. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) shows the incorrect headlamp aim. 10.
Vehicle Service and Care Taillamps (Five-Door Hatchback) 9-29 To replace one of these bulbs: 1. Open the liftgate. 2. To replace the bulbs on the driver side, turn both locks and remove the cover. 2. Turn the bulb socket counterclockwise and pull straight out. 3. Turn bulb counterclockwise and remove. 4. Install new bulb. 5. Reverse Steps 2 through 4 to reinstall. A. Backup Lamp B. Taillamp C.
9-30 Vehicle Service and Care 9. Install a new bulb without touching the glass. Taillamps (Three-Door Hatchback) 10. Reinstall the bulb assembly in taillamp assembly. 4. Turn the nuts counterclockwise and hold the outside of taillamp assembly. 5. Pull the taillamp assembly straight out. 6. Remove the three nuts. 11. Make sure the seals are applied to the taillamp assembly and screws. 7. Press on the tabs on the outside of bulb assembly and remove the bulb assembly. 12.
Vehicle Service and Care 9-31 To replace one of these bulbs: 1. Open the liftgate. See Liftgate on page 2-6 for more information. 2. Detach the plug connector from the bulb assembly. 5. Remove the seal. 6. Press on the tabs on outside of bulb assembly and remove the bulb assembly. 7. Remove the bulb from the bulb assembly. 8. Install a new bulb without touching the glass. 3. Turn the nuts counterclockwise and hold the outside of taillamp assembly. 4. Pull the taillamp assembly straight out. 9.
9-32 Vehicle Service and Care License Plate Lamp To replace one of these bulbs: 2. Turn and pull the license plate lamp toward you through the opening. 1. Push tab in and pull down on it to remove the license plate lamp. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket. 4. Install the new bulb. 5. Reverse Steps 1 through 3 to reinstall the license plate lamp.
Vehicle Service and Care Replacement Bulbs Exterior Lamp Front Turn Signal Lamp License Plate Lamp Parking Lamp Taillamp Bulb Number 3157 NAK W5W 4157K W21 For replacement bulbs not listed here, contact your dealer/retailer. Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty.
9-34 Vehicle Service and Care Windshield Wiper Fuses Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed. The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems.
Vehicle Service and Care Fuses 1 2 Usage Antilock Brake System (ABS) Valves ABS Pump Fuses 4 5 Usage Climate Control System (Ignition) Engine Cooling Fan (AT and AC only) Fuses 6 7 9-35 Usage Engine Cooling Fan Windshield & Liftgate Glass Washer Motor
9-36 Vehicle Service and Care Fuses Usage 8 Horn 10 Door Locks 13 Foglamps Windshield Wipers (high speed) Windshield Wipers (low speed) Antilock Brake System, Brake Lamp Switch Vacuum Pump Starter Air Conditioning Clutch Engine Control Module (ECM) (Main Relay) ECM (Battery) Fuel Pump/Injectors 14 15 16 17 18 20 21 22 24 Fuses Usage 26 ECM (Sensor and Actuators) 27 Power Steering 28 29 30 32 34 35 36 Automatic Transmission (Battery) Automatic Transmission (Ignition) ECM (Ignition) Brake Sw
Vehicle Service and Care 9-37 Use the fuse puller, to remove and replace fuses.
9-38 Fuses 16 17 18 21 22 23 24 29 34 38 39 40 Vehicle Service and Care Usage Front Passenger Seat Detection Sensor Tire Pressure Monitoring System (TPMS)/ Rain Sensor/Inside Rearview Mirror Interior Lights Outside Mirror Heating Sunroof Rear Power Window Diagnostic Link Connector Accessory Power Outlet (APO) Sunroof Door Locks Seat Heating Driver Seat Heating Front Passenger Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer.
Vehicle Service and Care CAUTION (Continued) • Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them. See High-Speed Operation on page 9-47 for inflation pressure adjustment for high speed driving. Low-Profile Tires If the vehicle has 225/40ZR18 or 215/45R18 size tires, they are classified as low-profile performance tires. These tires are designed for very responsive driving on wet or dry pavement.
9-40 Vehicle Service and Care See your dealer/retailer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 9-54. If you choose to use winter tires: • Use tires of the same brand and tread type on all four wheel positions. Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.
Vehicle Service and Care (D) Tire Identification Number (TIN): The letters and numbers following DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
9-42 Vehicle Service and Care (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 60 psi (420 kPa). For more information on tire pressure and inflation see Inflation - Tire Pressure on page 9-46. (F) Tire Size : A combination of letters and numbers define a tire’s width, height, aspect ratio, construction type, and service description.
Vehicle Service and Care (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load range and speed rating of the tire. The load index represents the load carry capacity a tire is certified to carry.
9-44 Vehicle Service and Care DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Loading the Vehicle on page 8-30.
Vehicle Service and Care Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer’s recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 9-46 and Loading the Vehicle on page 8-30. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.
9-46 Vehicle Service and Care Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not.
Vehicle Service and Care Remove the valve cap from the tire valve stem. Press the tire gage firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve.
9-48 Vehicle Service and Care When high-speed driving ends, return the tire pressure to the recommended cold inflation pressure shown on the Tire and Loading Information label. See Loading the Vehicle on page 8-30. Tire pressure should be checked and correctly set when the tires are cold. See Inflation - Tire Pressure on page 9-46. Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels.
Vehicle Service and Care When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
9-50 Vehicle Service and Care Tire Pressure Monitor Operation The Tire Pressure Monitor System (TPMS) is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire. The TPMS sensors monitor the air pressure in the vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle.
Vehicle Service and Care TPMS Malfunction Light The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. Some of the conditions that can cause the malfunction light to come on are: • One of the road tires has been replaced with the spare tire. The spare tire does not have a TPMS sensor.
9-52 Vehicle Service and Care { CAUTION Use this pattern when rotating the vehicle tires. Do not include the compact spare tire in the tire rotation. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel bolts become loose after time. The wheel could come off and cause a crash. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle using a scraper or wire brush.
Vehicle Service and Care When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
9-54 Vehicle Service and Care Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Vehicle Service and Care { CAUTION If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires.
9-56 Vehicle Service and Care Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States.
Vehicle Service and Care Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
9-58 Vehicle Service and Care Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment might need to be checked.
Vehicle Service and Care Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 9-60 for more information. Used Replacement Wheels { CAUTION Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash.
9-60 Vehicle Service and Care Tire Changing If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side.
Vehicle Service and Care CAUTION (Continued) 3. Turn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. 9-61 Removing the Spare Tire and Tools The equipment you will need is located in the rear storage area. 1. Open the liftgate. See Liftgate on page 2-6. To be certain the vehicle will not move, put blocks at the front and rear of the tire farthest away from the one being changed.
9-62 Vehicle Service and Care Removing the Flat Tire and Installing the Spare Tire 1. If your vehicle has wheel covers, remove the cover. Do not try to put a wheel cover on your compact spare tire. It will not fit. Store the wheel cover in the trunk until you have the flat tire repaired or replaced. 5. The jack and tools are stored below the spare tire. 6. The tools you will be using include the jack (A), wheel wrench (B) and jack handle (C).
Vehicle Service and Care 9-63 { CAUTION Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty. 4. Position the jack lift head at the jack location nearest the flat tire.
9-64 Vehicle Service and Care { CAUTION 6. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit under the vehicle. 7. Remove all of the wheel bolts. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel bolts become loose after time. The wheel could come off and cause an accident.
Vehicle Service and Care 9. Place the compact spare tire on the wheel-mounting surface. 10. Reinstall the wheel bolts with the rounded end of the bolts toward the wheel. Tighten each bolt by hand until the wheel is held against the hub. 11. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. 12. Tighten the wheel bolts firmly in a crisscross sequence, as shown.
9-66 Vehicle Service and Care Storing a Flat or Spare Tire and Tools To store a flat or spare tire and tools, do the following: { CAUTION Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. 2. Place the flat tire face down into the spare tire hub. A. Jack B. Wheel Wrench C. Jack Handle 1. Replace the jack and tools as shown. 3.
Vehicle Service and Care Compact Spare Tire Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). 4. Put the load floor back in place. The compact spare tire is for temporary use only. Replace the compact spare with a full-size tire as soon as possible. After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated.
9-68 Vehicle Service and Care Jump Starting If your battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Vehicle Service and Care 4. Open the hoods and locate the batteries. Find the positive (+) and negative (−) terminal locations on each vehicle. Your vehicle’s positive (+) terminal is identified by “+” sign on battery case or terminal. Engine Compartment Overview on page 9-6. { CAUTION An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
9-70 Vehicle Service and Care 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some things you to know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to the engine lift hook. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too.
Vehicle Service and Care To disconnect the jumper cables from both vehicles, do the following: 10. Now start the vehicle with the good battery and run the engine for a while. 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service.
9-72 Vehicle Service and Care Towing Towing Your Vehicle The vehicle was neither designed nor intended to be towed with any of its wheels on the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle needs to be towed. See Roadside Assistance Program on page 11-5. Notice: Dolly towing or dinghy towing your vehicle may cause damage because of reduced ground clearance. Always put your vehicle on a flatbed truck.
Vehicle Service and Care When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth.
9-74 Vehicle Service and Care Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: • For liquids: gently blot the remaining soil with a paper towel.
Vehicle Service and Care change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on leather. Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust.
9-76 Vehicle Service and Care If your vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on your vehicle.
Vehicle Service and Care page 9-80. Follow all manufacturers’ directions regarding correct product usage, necessary safety precautions and appropriate disposal of any vehicle care product. Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.
9-78 Vehicle Service and Care Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Notice: If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels.
Vehicle Service and Care 9-79 Finish Damage Underbody Maintenance Chemical Paint Spotting Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Chemicals used for ice and snow removal and dust control can collect on the underbody.
9-80 Vehicle Service and Care Vehicle Care/Appearance Materials Description Usage Polishing Cloth Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil, and asphalt. Chrome Cleaner and Polish Use on chrome or stainless steel. White Sidewall Tire Cleaner Removes soil and black marks from whitewalls and raised white lettering. Vinyl Cleaner Cleans vinyl. Glass Cleaner Removes dirt, grime, smoke and fingerprints.
Vehicle Service and Care Description Usage Foaming Tire Shine Low Gloss Cleans, shines, and protects tires. No wiping necessary. Wash Wax Concentrate Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Spot Lifter Quickly removes spots and stains from carpets, vinyl, and cloth upholstery. Odor Eliminator Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.
9-82 Vehicle Service and Care ✍ NOTES
Technical Data Technical Data Vehicle Identification Vehicle Identification Vehicle Identification Number (VIN) Vehicle Identification Number (VIN) ..................10-1 Service Parts Identification Label ...........10-1 Capacities and Specifications Capacities and Specifications ..................10-2 This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle.
10-2 Technical Data Capacities and Specifications The following approximate capacities are given in English and metric conversions. See “Fluids and Lubricants” in the index of the “Limited Warranty, Maintenance and Owner Assistance Information” manual. Capacities Application Air Conditioning Refrigerant English Metric For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information.
Technical Data Engine Specifications Engine 1.8L L4 VIN Code Transmission Spark Plug Gap 1 Automatic Manual 0.035 in (0.
10-4 Technical Data ✍ NOTES
Customer Information Customer Information Customer Information Customer Satisfaction Procedure .......................11-1 Online Owner Center ........11-4 Customer Assistance for Text Telephone (TTY) Users ..............................11-4 Customer Assistance Offices ............................11-5 GM Mobility Reimbursement Program ..........................11-5 Roadside Assistance Program ..........................11-5 Scheduling Service Appointments ..................11-8 Courtesy Transportation ....
11-2 Customer Information STEP TWO: Should you need additional assistance, in the U.S., contact the Saturn Customer Assistance Center by calling 1-800-553-6000. In Canada, call the Saturn Customer Communication Centre at 1-800-263-1999. A Saturn Customer Assistance Center team member will handle your call and assist in providing product and warranty information, the nearest retailer location, roadside assistance, brochures, literature and discuss any concerns you may have.
Customer Information Contact the BBB Auto Line Program by using the toll-free telephone number or by writing them at the following address: STEP THREE (Canadian Owners): BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800 Arlington, VA 22203-1838 Telephone: 1-800-955-5100 dr.bbb.
11-4 Customer Information Online Owner Center My GM Canada (Canada only) (United States only) My GM Canada is a password-protected section of gmcanada.com where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. This is a resource for your Saturn ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders.
Customer Information Customer Assistance Offices Saturn encourages customers to call the toll-free number for assistance. If a customer wishes to write to Saturn, the letter should be addressed to: Saturn Customer Assistance Center 100 Saturn Parkway Mail Code 371-999-S24 Spring Hill, TN 37174-1500 1-800-553-6000 1-800-833-6000 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-553-6000 In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd.
11-6 Customer Information Who is Covered? Roadside Assistance coverage is for the vehicle operator, regardless of ownership. In Canada, a person driving this vehicle without the consent of the owner is not eligible for coverage. Services Provided The following services are provided in the U.S. and Canada up to 5 years/100,000 miles (160 000 km), whichever comes first, and, in Canada only, up to a maximum of $100.
Customer Information • Trip Interruption Benefits and Assistance (Canada Only): In the event of a warranty related vehicle disablement, while en route and over 250 kilometres from the original point of departure, you might qualify for trip interruption expense assistance. This assistance covers reasonable reimbursement of up to a maximum of $500 (Canadian) for (A) meals (maximum of $50/day), (B) lodging (maximum of $100/night), and (C) alternate ground transportation (maximum of $40/day).
11-8 Customer Information Towing and Road Service Exclusions Scheduling Service Appointments Specifically excluded from Roadside Assistance coverage are towing or services for vehicles operated on a non-public roadway or highway, fines, impound towing caused by a violation of local, Municipal, State, Provincial or Federal law, and mounting, dismounting or changing of snow tires, chains, or other traction devices.
Customer Information Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, Saturn helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your retailer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
11-10 Customer Information Additional Program Information All program options, such as shuttle service, may not be available at every retailer. Please contact your retailer for specific information about availability. All Courtesy Transportation arrangements will be administered by appropriate retailer personnel.
Customer Information Aftermarket parts are not covered by your GM New Vehicle Limited Warranty, and any vehicle failure related to such parts are not covered by that warranty. Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs.
11-12 Customer Information • If you need roadside assistance, call GM Roadside Assistance. See Roadside Assistance Program on page 11-5 for more information. • If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver’s name, the service’s name, and the phone number. • Remove any valuables from your vehicle before it is towed away.
Customer Information Insurance pays the bill for the repair, but you must live with the repair. Depending on your policy limits, your insurance company may initially value the repair using aftermarket parts. Discuss this with your repair professional, and insist on Genuine GM parts. Remember if your vehicle is leased you may be obligated to have the vehicle repaired with Genuine GM parts, even if your insurance coverage does not pay the full cost.
11-14 Customer Information Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately, in addition to notifying General Motors of Canada Limited.
Customer Information Owner Publications Information on how to obtain product bulletins and as described below is applicable only in the fifty U.S. states and the District of Columbia, and only for cars and light trucks with a Gross Vehicle Weight Rating (GVWR) less than 10,000 pounds (4 536 kg). Copies of individual bulletins are also at your participating Saturn retailer. You can ask to see them.
11-16 Customer Information Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
Customer Information Saturn will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office; as part of Saturn’s defense of litigation through the discovery process; or, as required by law.
11-18 Customer Information ✍ NOTES
INDEX A Accessories and Modifications ...................... 9-3 Accessory Power Outlets ...... 4-10 Adding Equipment to Your Airbag-Equipped Vehicle .... 1-35 Additives, Fuel ..................... 8-36 Add-On Electrical Equipment ....................... 9-33 Air Cleaner/Filter, Engine ....... 9-11 Air Conditioning ..................... 7-1 Airbag Passenger Status Indicator ....................... 4-15 Readiness Light ................ 4-14 System, Replacing Parts After a Crash ................
i-2 INDEX C California Fuel ..................... 8-35 California Perchlorate Materials Requirements ....... 9-3 California Proposition 65 Warning ............................ 9-3 Canadian Owners ..................... ii Capacities and Specifications ................... 10-2 Carbon Monoxide ......... 8-14, 8-27 Care, Safety Belts ................ 1-22 Cargo Cover ......................... 3-1 Cargo Tie Downs ................... 3-1 Cautions and Notices ............... iii Chains, Tire ....................
INDEX D Daytime Running Lamps ......... 5-2 Defensive Driving ................. 8-16 Delayed Headlamps ............... 5-2 Doing Your Own Service Work ..................... 9-4 Dome Lamps ........................ 5-3 Door Ajar Light ........................ 4-24 Locks ............................... 2-5 Power Door Locks .............. 2-5 Rear Door Security Locks .... 2-6 Driver Information Center (DIC) .................... 4-26 DIC Operation and Displays ...............
i-4 INDEX F Filter Engine Air Cleaner ............ 9-11 Finish Damage .................... 9-79 Fixed Mast Antenna ............. 6-25 Flashers, Hazard Warning ....... 4-4 Flash-to-Pass ........................ 4-8 Flat Tire .............................. 9-60 Flat Tire, Changing ............... 9-60 Flat Tire, Storing .................. 9-66 Fluid .................................. 9-12 Automatic Transmission ..... 9-12 Power Steering ................. 9-20 Windshield Washer ...........
INDEX Hood Release ............................ 9-5 Horn .................................... 4-4 How to Wear Safety Belts Properly .......................... 1-12 Hydraulic Clutch ................... 9-12 I Ignition Positions ................... 8-2 Immobilizer ........................... 2-7 Immobilizer Operation ............. 2-8 Infants and Young Children, Restraints ........... 1-38 Inflation - Tire Pressure ......... 9-46 Instrument Panel Brightness ......................... 5-3 Cluster .............
i-6 INDEX Loading Your Vehicle ............ 8-30 Locks Door ................................. 2-5 Power Door ....................... 2-5 Rear Door Security Locks .... 2-6 Loss of Control .................... 8-23 Low Fuel Warning Light ........ 4-25 Lumbar Seat Adjustment ......... 1-3 M Malfunction Indicator Light ..... 4-20 Manual Seats ........................ 1-2 Manual Transmission Fluid ............................... 9-12 Operation .......................... 8-9 Manual, Using .....................
INDEX Power (cont.) Steering Fluid ................... 9-20 Windows ......................... 2-10 Pressure Cap ...................... 9-15 Privacy ............................. 11-15 Event Data Recorders ..... 11-16 Navigation System .......... 11-17 OnStar .......................... 11-17 Radio Frequency Identification ................ 11-17 R Radio Frequency Identification (RFID), Privacy .......................... 11-17 Radio(s) ............................... 6-2 Radios Reception .....................
i-8 INDEX S Safety Belts .......................... 1-8 Care of ........................... 1-22 Check ............................. 1-22 How to Wear Safety Belts Properly ............... 1-12 Lap-Shoulder Belt ............. 1-17 Reminder Light ................. 4-14 Replacing Parts After a Crash ....................... 1-23 Safety Belt Extender ......... 1-22 Safety Belt Use During Pregnancy .................... 1-21 Seats Head Restraints ................. 1-5 Heated Seats - Rear ...........
INDEX T Tachometer ......................... 4-13 Taillamps .................... 9-29, 9-30 Theft-Deterrent, Radio ........... 6-24 Theft-Deterrent Systems ......... 2-7 Content Theft-Deterrent ....... 2-9 Immobilizer ........................ 2-7 Immobilizer Operation ......... 2-8 Tilt Wheel ............................. 4-4 Tire Pressure Light .................. 4-19 Tires .................................. 9-38 Buying New Tires ............. 9-54 Chains ............................
i-10 INDEX U W Uniform Tire Quality Grading ........................... 9-56 Using this Manual ..................... ii Warning Lights, Gages and Indicators .................. 4-11 Warnings DIC Warnings and Messages .................... 4-37 Hazard Warning Flashers .... 4-4 Wheels Alignment and Tire Balance ....................... 9-58 Different Size ................... 9-55 Replacement .................... 9-58 Where to Put the Restraint .... 1-43 Windows ............................. 2-10 Power .....
