2010 Saturn OUTLOOK Owner Manual M In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information . . . . . . . . 1-3 Vehicle Features . . . . . . . . . . . . . 1-14 Performance and Maintenance . . . . . . . . . . . . . . . . 1-19 Keys, Doors and Windows . . . 2-1 Keys and Locks . . . . . . . . . . . . . . . 2-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Vehicle Security. . . . . . . . . . . . . .
010 Saturn OUTLOOK Owner Manual M Jump Starting . . . . . . . . . . . . . . . 10-78 Towing . . . . . . . . . . . . . . . . . . . . . . 10-83 Appearance Care . . . . . . . . . . . 10-86 Service and Maintenance . . . 11-1 General Information . . . . . . . . . . 11-1 Scheduled Maintenance . . . . . . 11-2 Recommended Fluids, Lubricants, and Parts . . . . . . . 11-7 Maintenance Records . . . . . . . . 11-9 Technical Data . . . . . . . . . . . . . . . 12-1 Vehicle Identification . . . . . . . . .
Introduction SATURN, the SATURN Emblem, and the name OUTLOOK are registered trademarks of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Saturn Corporation wherever it appears in this manual.
iv Introduction Using this Manual To quickly locate information about the vehicle, use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Danger, Warnings, and Cautions { WARNING These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicle damage. This would not be covered by the vehicle's warranty.
Introduction Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio® Steering Wheel Controls or OnStar $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant Temperature O : Exterior Lamps # : Fog Lamps .
vi Introduction 2 NOTES
In Brief In Brief Instrument Panel Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information Initial Drive Information . . . . . . . . 1-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 1-4 Remote Vehicle Start . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . 1-5 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Windows . . . . . . . . . . . . . . . . . . . . . . 1-6 Seat Adjustment . . . . . . . . . . . . . .
1-2 In Brief Instrument Panel
In Brief A. Air Vents on page 8‑12. B. Turn and Lane-Change Signals on page 6‑4. K. Steering Wheel Adjustment on page 5‑2. L. Horn on page 5‑5. C. Instrument Cluster on page 5‑12. M. Steering Wheel Controls on page 5‑3. D. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) (With DIC Buttons) on page 5‑24 or Driver Information Center (DIC) (Without DIC Buttons) on page 5‑30. N. Hazard Warning Flashers on page 6‑4. E. Instrument Panel Storage on page 4‑1. F.
1-4 In Brief Remote Keyless Entry (RKE) System The RKE transmitter is used to remotely lock and unlock the doors from up to 60 m (195 feet) away from the vehicle. To open or close the liftgate, press and hold & until the liftgate begins to move. Press L and release to locate the vehicle. Press L and hold for three seconds to sound the panic alarm. When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running.
In Brief Door Locks Liftgate To lock or unlock a door manually: To open the liftgate the vehicle must be in P (Park). Press the touchpad under the liftgate handle. To close the liftgate, use the pull cup or pull strap as an aid. . From the inside use the door lock knob on the window sill. . From the outside turn the key toward the front or rear of the vehicle, or press the Q or " button on the Remote Keyless Entry (RKE) transmitter.
1-6 In Brief Windows Seat Adjustment Manual Seats Move the seat forward or rearward by moving the control (A) forward or rearward. 1. Pull the handle under the seat to unlock the seat. Raise or lower the entire seat by moving the control (A) up or down. 2. Slide the seat to the desired position and release the handle. See Power Seat Adjustment on page 3‑3. Try to move the seat to be sure it is locked in place. To raise or recline the seatback, tilt the top of the control (B) forward or rearward.
In Brief Second Row Seats Third Row Seats Heated Seats The third row seats can be folded forward or removed. Heated Front Seats 1-7 The heated seat controls are located on the center console. The engine must be running to operate them. I : Press to turn on the heated seatback. J : Press to turn on or off the heated seat and seatback. For more information see Heated Front Seats on page 3‑8.
1-8 In Brief Heated and Ventilated Seats Safety Belt Sensing System for Passenger Airbag On vehicles with this feature, the controls are on the front doors near the handle. H: z: Press to ventilate the seat. Press to heat the seat. For more information see Heated and Ventilated Front Seats on page 3‑8. Head Restraint Adjustment Do not drive until the head restraints for all occupants are installed and adjusted properly. For more information see Head Restraints on page 3‑2.
In Brief started. See Passenger Sensing System on page 3‑37 for more information. Controls for the outside power mirrors are located on the driver door armrest. Mirror Adjustment 1. Press (A) or (B) to select the driver or passenger side mirror. Exterior Mirrors 2. Press one of the four arrows located on the control pad to adjust the mirror. 3. Press either (A) or (B) again to deselect the mirror. Folding Mirrors For vehicles with outside power foldaway mirrors: 1.
1-10 In Brief Steering Wheel Adjustment Power Tilt Wheel Interior Lighting Dome Lamps The dome lamps are located in the overhead console and above the rear seat passengers. The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. To manually turn them on, turn the instrument panel brightness control clockwise to the farthest position. The adjustment lever is located on the left side of the steering column.
In Brief Reading Lamps Press the button near each lamp to turn them on or off. For more information, see: . Dome Lamps on page 6‑5. . Instrument Panel Illumination Control on page 6‑5. Exterior Lighting O : Turns the automatic light control on or off. AUTO : Automatic operation of the headlamps at normal brightness and other exterior lamps. 1-11 Windshield Wiper/Washer The windshield wiper/washer lever is located on the left side of the steering column.
1-12 In Brief 6: Delays wiping cycle. Turn the band up for more frequent wipes or down for less frequent wipes. Climate Controls 1 : Slow wipes. 2 : Fast wipes. Windshield Washer J: Press the button at the end of the turn signal/lane change lever to spray washer fluid on the windshield. See Windshield Wiper/Washer on page 5‑5. A. Fan Control E. REAR (Rear Climate Control) B. Temperature Control F. Air Recirculation C. Air Delivery Mode Control G. Rear Window Defogger D.
In Brief 1-13 See Climate Control Systems on page 8‑1 or Dual Automatic Climate Control System on page 8‑4 (If Equipped). For more information about the rear climate control, see Rear Climate Control System (Rear Climate Control Only) on page 8‑10 or Rear Climate Control System (Rear Climate with Rear Seat Audio) on page 8‑11. A. Fan Control H. Display B. AUTO I. C. Defrost J. Rear Window Defogger D. Air Recirculation K. Air Conditioning E. REAR (Rear Climate Control) L. PASS (Passenger) F.
1-14 In Brief 4: Vehicle Features Change the display between the radio station frequency and the time, if equipped. While the ignition is off, press 4 to display the time. Radio(s) For more information about these and other radio features, see Operation on page 7‑2. Storing a Favorite Station A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio FAV button.
In Brief 1-15 Setting the Clock Satellite Radio Portable Audio Devices To set the time and date for the radio with CD, DVD, and USB Port: Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. This vehicle may have an auxiliary input located on the radio faceplate and a USB port located in the center console. External devices such as iPod®, laptop computers, MP3 players, CD changers, USB storage device, etc.
1-16 In Brief The Bluetooth-enabled cell phone must be paired with the in-vehicle Bluetooth system before it can be used in the vehicle. Not all phones will support all functions. b g : Press to silence the vehicle speakers only. Press again to turn the sound on. Press and hold longer than two seconds to interact with OnStar® or Bluetooth systems. See Bluetooth on page 7‑45. + e − e : Increases or decreases volume. Steering Wheel Controls c : Press to reject an incoming call, or to end a call.
In Brief U : Press to customize the feature settings on your vehicle. See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information. Cruise Control 1-17 Storage Compartments T: Press to display the oil life, park assist on vehicles with this feature, units, tire pressure readings on vehicles with this feature, RKE transmitter programming, and compass calibration and zone setting on vehicles with this feature.
1-18 In Brief Power Outlets The vehicle has three 12-volt accessory power outlets which can be used to plug in electrical equipment, such as a cellular telephone. The power outlets are located: Press the buttons (B, C) on the front of the consoles to access the upper and lower storage areas. Increase the storage area by folding the top of the console forward. Lift up on rear console handle (A) and pull forward. See Floor Console Storage on page 4‑2. . On the instrument panel below the climate controls.
In Brief Performance and Maintenance Tire Pressure Monitor This vehicle may have a Tire Pressure Monitor System (TPMS). StabiliTrak® The traction control system limits wheel spin and the StabiliTrak system assists with directional control of the vehicle in difficult driving conditions. Both systems turn on automatically every time the vehicle is started. . . To turn off the traction control part of StabiliTrak, press and release 5 located on the instrument panel in front of the shift lever.
1-20 In Brief Engine Oil Life System The engine oil life system calculates engine oil life based on vehicle use and displays the CHANGE ENGINE OIL SOON message when it is time to change the engine oil and filter. The oil life system should be reset to 100% only following an oil change. Resetting the Oil Life System 1. Turn the ignition to ON/RUN, with the engine off. 2. If the vehicle has Driver Information Center (DIC) buttons: Press the vehicle information button until OIL LIFE REMAINING displays.
In Brief . . Replace the vehicle's tires with the same TPC Spec number molded into the tire's sidewall near the size. Follow recommended scheduled maintenance. Roadside Assistance Program U.S.: 1-800-553-6000 TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Saturn, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
1-22 In Brief OnStar services are available on all vehicles. For more information see the OnStar Owner's Guide or visit www.onstar.com (U.S.) or www.onstar.ca (Canada), contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press Q to speak with an OnStar advisor 24 hours a day, 7 days a week. For a full description of OnStar services and system limitations, see the OnStar Owner's Guide in the glove box.
In Brief On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions. See the OnStar Owner's Guide for more information. Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly. Press Q and request a vehicle diagnostic.
1-24 In Brief 2 NOTES
Keys, Doors and Windows Keys, Doors and Windows Doors Keys . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System Operation . . . . . . . . . . . Remote Vehicle Start . . . . . . . . . Door Locks . . . . . . . . . . . . . . . . . . . Power Door Locks . . . . . . . . . . . . Delayed Locking . . . . . . . . . . . . . . Automatic Door Locks . . . . . . . . . Lockout Protection . . . . . . . . . . . .
2-2 Keys, Doors and Windows Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. Keys and Locks Keys If you are locked out of the vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 13‑5. { WARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Keys, Doors and Windows If there is a decrease in the RKE operating range: . Check the distance. The transmitter may be too far from the vehicle. . Check the location. Other vehicles or objects may be blocking the signal. . Check the transmitter's battery. See “Battery Replacement” later in this section. . There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2‑2.
2-4 Keys, Doors and Windows Pressing K on the RKE transmitter disarms the content theft-deterrent system. See Anti-Theft Alarm System on page 2‑13. & (Power Liftgate): Press and hold until the liftgate begins to move to open or close the liftgate. The taillamps flash and a chime sounds to indicate when the liftgate is opening or closing. L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times.
Keys, Doors and Windows 3. Insert the new battery, positive side facing down. Replace with a CR2032 or equivalent battery. 4. Snap the transmitter back together. Remote Vehicle Start If the vehicle has the remote start feature, the RKE transmitter functions have an increased range of operation. However, the range may be less while the vehicle is running. This vehicle may have a remote starting feature that starts the engine from outside of the vehicle.
2-6 Keys, Doors and Windows If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done. Extending Engine Run Time To extend the engine run time by 10 minutes, repeat Steps 1 though 3 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time.
Keys, Doors and Windows Door Locks WARNING (Continued) { WARNING Unlocked doors can be dangerous. . . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven.
2-8 Keys, Doors and Windows Automatic Door Locks Vehicles with an automatic lock/ unlock feature enable you to program the vehicle's power door locks. This feature can be programmed through the Driver Information Center (DIC). See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information. the key is in the ignition, all of the doors will lock and then the front passenger door will unlock.
Keys, Doors and Windows Doors WARNING (Continued) Liftgate . Manual Liftgate Operation { WARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open: . Close all of the windows.
2-10 Keys, Doors and Windows Power Liftgate Operation { WARNING . Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting.
Keys, Doors and Windows 2-11 function will continue to completion. If the vehicle is shifted out of P (Park) and the vehicle accelerates before the power liftgate latches closed, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. The power liftgate must be closed and latched before driving. Power Liftgate Button on Center Console . Press the liftgate button on the center console. . Press the touchpad switch on the outside liftgate handle.
2-12 Keys, Doors and Windows If the liftgate comes across more obstacles on the same power cycle, the power function deactivates, and you must manually open or close the liftgate. A message displays, LIFTGATE OPEN, to indicate that the liftgate is open. See Driver Information Center (DIC) (With DIC Buttons) on page 5‑24 or Driver Information Center (DIC) (Without DIC Buttons) on page 5‑30 for more information.
Keys, Doors and Windows 30 seconds. The content theft deterrent alarm is not armed until the security light goes off. Vehicle Security Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Anti-Theft Alarm System On vehicles with an anti-theft alarm system, to activate the system: . Press Q on the Remote Keyless Entry (RKE) transmitter or the power door lock switch when any door is open.
2-14 Keys, Doors and Windows 3. Get out of the vehicle, close the door and wait for the security light to go out. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm. If the alarm does not sound when it should, but the vehicle's headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 10‑31.
Keys, Doors and Windows Up to 10 keys may be programmed to the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer/retailer or a locksmith who can service PASS-Key® III+ to have keys made and programmed to the system. See your dealer/retailer or a locksmith who can service PASS-Key® III+ to get a new key blank that is cut exactly as the ignition key that operates the system.
2-16 Keys, Doors and Windows Exterior Mirrors Power Mirrors Convex Mirrors 4. Press either (A) or (B) again to deselect the mirror. { WARNING A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex shaped.
Keys, Doors and Windows For vehicles with outside power foldaway mirrors: Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if: The controls for power foldaway mirrors are located on the driver door armrest. 1. Press (C) to fold the mirrors out to the driving position. 2. Press (D) to fold the mirrors in to the folded position. . The mirrors are accidentally obstructed while folding. . They are accidentally manually folded/unfolded. . The mirrors vibrate at normal driving speeds.
2-18 Keys, Doors and Windows Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse). This allows the driver to view the curb for parallel parking. The passenger and/or driver mirror returns to its original position when the vehicle is shifted out of R (Reverse), or the ignition is turned off or to OFF/LOCK.
Keys, Doors and Windows The vehicle may also have a Rear Vision Camera (RVC). See Rear Vision Camera (RVC) on page 9‑34 for more information. If the vehicle has RVC, the O button for turning the dimming feature on or off will not be available. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water. Windows { WARNING Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous.
2-20 Keys, Doors and Windows Power Windows Express-Up/Express-Down Windows { WARNING Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children.
Keys, Doors and Windows 2. Press and continue to hold the window switch until the window is fully open. 3. Pull up and hold the window switch to close the window. Continue to hold it briefly after the window is fully closed. 4. Repeat for each window that has the express-up feature. Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature.
2-22 Keys, Doors and Windows Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. Roof Sunroof The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9‑17 The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open.
Keys, Doors and Windows Do not keep the sunroof open for long periods of time while the vehicle is not in use. Debris can collect in the tracks, damage the sunroof operation and plug the water draining system. Notice: The rear sunshade could be damaged if you attempt to open or close it manually. Do not manually open or close the rear sunshade. To open the rear sunshade, located over the second row seats, press and release the rear of the switch.
2-24 Keys, Doors and Windows 2 NOTES
Seats and Restraints Seats and Restraints Safety System Check . . . . . . . . 3-28 Safety Belt Care . . . . . . . . . . . . . 3-28 Replacing Safety Belt System Parts After a Crash . . . . . . . . . 3-29 Airbag System Head Restraints Head Restraints . . . . . . . . . . . . . . . 3-2 Front Seats Seat Adjustment . . . . . . . . . . . . . . 3-3 Power Seat Adjustment . . . . . . . 3-3 Lumbar Adjustment . . . . . . . . . . . 3-5 Reclining Seatbacks . . . . . . . . . . 3-6 Heated Front Seats . . . . . . . . .
3-2 Seats and Restraints Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. { WARNING With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head.
Seats and Restraints 3-3 Power Seat Adjustment Front Seats Seat Adjustment { WARNING You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving. A. Manual Seat Adjustment Handle B. Driver Seat Height Adjuster. C. See Reclining Seatbacks on page 3‑6.
3-4 Seats and Restraints Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. Memory Seat and Mirrors Not all mirrors will have the ability to save and recall the mirror positions. The vehicle may have additional features to adjust the power seat: . 2. Press and hold button 1 until two beeps let you know that the position has been stored. Raise or lower the entire seat by moving the power seat adjustment control (A) up or down. .
Seats and Restraints There is no adjustment when the position has not been changed by another seating position or the easy exit feature. See “MEMORY SEAT RECALL” under Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information. To stop recall movement of the memory feature at any time, press one of the power seat controls, memory buttons, or power mirror buttons. If something has blocked the driver seat while recalling a memory position, the driver seat recall may stop working.
3-6 Seats and Restraints Power Lumbar Reclining Seatbacks On vehicles with power lumbar, the control is located on the outboard side of the seat. See “Power Lumbar” under Power Seat Adjustment on page 3‑3 for more information. Manual Reclining Seatbacks To increase or decrease lumbar support, press and hold the front or rear of the control (C). Release the control when the seatback reaches the desired level of lumbar support.
Seats and Restraints Power Reclining Seatbacks In vehicles with seats that have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat. See Power Seat Adjustment on page 3‑3 for more information. To recline the seatback: . Tilt the top of the control (B) rearward. . To bring the seatback forward, tilt the top of the control forward. 3-7 { WARNING Sitting in a reclined position when the vehicle is in motion can be dangerous.
3-8 Seats and Restraints Heated Front Seats { WARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat.
Seats and Restraints On vehicles with the heated and ventilated seat feature, the controls are located on the front doors near the door handle. H (Ventilated Seat): Press to ventilate the entire seat. This symbol appears on the climate control display to indicate that the feature is on. z (Heated Seat and Seatback): Press to heat the entire seat. This symbol appears on the climate control display to indicate that the feature is on. For either feature press the button once for the highest setting.
3-10 Seats and Restraints Entering and Exiting the Third Row 5. Pull the sliding seat lever (C) forward and move the seatback forward. The seat cushion will fold, and the entire seat will slide forward. { WARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
Seats and Restraints Reclining the Seatbacks To recline the seatback: 1. Leaning forward in the seat, pull the reclining seatback strap (B). 2. Move the seatback to the desired position, then release the strap to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked. Folding the Rear Seat To fold the second row seats: 1. Remove anything on or under the seat. 2. Place the armrest in the upright position, and unfasten the safety belt. 3.
3-12 Seats and Restraints To return the seatback to the seating position: 1. Raise the seatback into place by using the pullstrap from the rear of the vehicle, or by pushing it into place from inside the vehicle. 2. The headrest must be locked into place before sitting in the seat. 2. Disconnect the rear safety belt mini-latch, using a key in the slot on the mini-buckle, let the belt retract into the headliner. Stow the mini-latch in the holder located in the headliner. 3.
Seats and Restraints { WARNING A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted. 4. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist. 5. Pull on the safety belt to be sure the mini-latch is secure.
3-14 Seats and Restraints 2. Place the seat on the vehicle floor so that the front seat hooks are on the vehicle bars. 3. Reinstall the bolts, and torque to 55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place. 4. Raise the seatback to its upright position. Push and pull on the seatback to make sure it is locked into place. 5. Push the headrest up into position. Push and pull on the headrest to make sure it is locked into place. 6.
Seats and Restraints A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without safety belts they could have been badly hurt or killed. 3-15 Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter ...
3-16 Seats and Restraints The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Seats and Restraints Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down.
3-18 Seats and Restraints How to Wear Safety Belts Properly This section is only for people of adult size. First, before you or your passenger(s) wear a safety belt, there is important information you should know. The shoulder belt locks if there is a sudden stop or crash. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants.
Seats and Restraints { WARNING Q: What is wrong with this? You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. 3-19 { WARNING You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries.
3-20 Seats and Restraints Q: What is wrong with this? { WARNING Q: What is wrong with this? You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong buckle. A: The belt is over an armrest.
Seats and Restraints { WARNING Q: What is wrong with this? You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
3-22 Seats and Restraints Q: What is wrong with this? A: The belt is behind the body. { WARNING You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries.
Seats and Restraints 3-23 Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Third Row Seats on page 3‑11 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
3-24 Seats and Restraints Shoulder Belt Height Adjuster Adjustment” later in this section for instructions on use and important safety information. 6. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull the stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. To unlatch the belt, push the button on the buckle.
Seats and Restraints Safety Belt Pretensioners To move it down, push down on the button (A) and move the height adjuster to the desired position. You can move the height adjuster up by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without pushing the button to make sure it has locked into position. This vehicle has safety belt pretensioners for the front outboard occupants.
3-26 Seats and Restraints Here is how to install a comfort guide to the safety belt: comfort guide, you will first need to move the headrest forward by pulling on the handle behind the seatback. The comfort guide will now be accessible. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. Outboard Positions 1. For the outboard positions, remove the guide from its storage clip on the interior body.
Seats and Restraints 3-27 { WARNING A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. 4.
3-28 Seats and Restraints Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Seats and Restraints { WARNING WARNING (Continued) Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. properly after a crash, have them inspected and any necessary replacements made as soon as possible. Replacing Safety Belt System Parts After a Crash { WARNING A crash can damage the safety belt system in the vehicle.
3-30 Seats and Restraints All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger. With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the seatback closest to the door.
Seats and Restraints Where Are the Airbags? { WARNING Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide. Always secure children properly in your vehicle.
3-32 Seats and Restraints The right front passenger frontal airbag is in the instrument panel on the passenger side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Seats and Restraints { WARNING If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat accessories that block the inflation path of a seat-mounted side impact airbag.
3-34 Seats and Restraints Frontal airbags are not intended to inflate during vehicle rollovers, rear impacts, or in many side impacts. In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. For moderate frontal impacts, dual-stage airbags inflate at a level less than full deployment.
Seats and Restraints Frontal airbag modules are located inside the steering wheel and instrument panel. For vehicles with seat-mounted side impact airbags, there are airbag modules in the side of the front seatbacks closest to the door. For vehicles with roof-rail airbags, there are airbag modules in the ceiling of the vehicle, near the side windows that have occupant seating positions.
3-36 Seats and Restraints { WARNING When an airbag inflates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have breathing problems but cannot get out of the vehicle after an airbag inflates, then get fresh air by opening a window or a door.
Seats and Restraints . . The vehicle has a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Recording and Privacy on page 13‑14 and Event Data Recorders on page 13‑15. Let only qualified technicians work on the airbag systems. Improper service can mean that an airbag system will not work properly. See your dealer/retailer for service. Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position.
3-38 Seats and Restraints According to accident statistics, children are safer when properly secured in a rear seat in the correct child restraint for their weight and size. We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts.
Seats and Restraints When the passenger sensing system has turned off the right front passenger frontal airbag, the off indicator will light and stay lit to remind you that the airbag is off. See Passenger Airbag Status Indicator on page 5‑16. The passenger sensing system is designed to turn on (may inflate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat.
3-40 Seats and Restraints recline the vehicle seatback and adjust the seat cushion, if adjustable, to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion. If the Off Indicator is Lit for an Adult-Size Occupant 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers. Also make sure the child restraint is not trapped under the vehicle head restraint.
Seats and Restraints Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
3-42 Seats and Restraints Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 13‑11. { WARNING For up to 10 seconds after the ignition is turned off and the battery is disconnected, an airbag can still inflate during improper service. You can be injured if you are close to an airbag when it inflates. Avoid yellow connectors.
Seats and Restraints Step Two of the Customer Satisfaction Procedure in this manual. If the vehicle has rollover roof-rail airbags, see Different Size Tires and Wheels on page 10‑53 for additional important information. Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will affect my airbag system? A: If you have questions, call Customer Assistance.
3-44 Seats and Restraints If the airbag readiness light stays on after the vehicle is started or comes on when you are driving, the airbag system may not work properly. Have the vehicle serviced right away. See Airbag Readiness Light on page 5‑15 for more information. Child Restraints Older Children The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster.
Seats and Restraints . Can proper safety belt fit be maintained for the length of the trip? If yes, continue. If no, return to the booster seat. Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child's pelvic bones in a crash.
3-46 Seats and Restraints { WARNING { WARNING Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury. The child might also slide under the lap belt. The belt force would then be applied right on the abdomen.
Seats and Restraints { WARNING WARNING (Continued) Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person's arms. An infant should be secured in an appropriate restraint. 3-47 child restraint in a rear seat.
3-48 Seats and Restraints Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available.
Seats and Restraints 3-49 Child Restraint Systems (B) Forward-Facing Child Seat (A) Rear-Facing Infant Seat A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child's body with the harness.
3-50 Seats and Restraints Securing an Add-On Child Restraint in the Vehicle { WARNING A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle.
Seats and Restraints child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “Never put a rear-facing child restraint in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { WARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
3-52 Seats and Restraints Lower Anchors and Tethers for Children (LATCH System) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Seats and Restraints Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
3-54 Seats and Restraints To assist you in locating the lower anchors, each second row anchor position has a label, near the crease between the seatback and the seat cushion. Third Row Second Row — Bucket Shown, Bench Similar i (Top Tether Anchor): Seating positions with top tether anchors. To assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover or near the anchor.
Seats and Restraints Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. See Where to Put the Restraint on page 3‑50 for additional information. Securing a Child Restraint Designed for the LATCH System { WARNING Third Row Seat The third row has one top tether anchor located at the bottom rear of the center seatback. This anchor should be used for the center seating position only. Never install two top tethers using the same top tether anchor.
3-56 Seats and Restraints { WARNING Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts.
Seats and Restraints 3-57 2.3. Route, attach and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback.
3-58 Seats and Restraints If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure.
Seats and Restraints 3-59 In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. If the child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
3-60 Seats and Restraints 6. If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑52 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. 5.
Seats and Restraints { WARNING WARNING (Continued) A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position.
3-62 Seats and Restraints 2. Put the child restraint on the seat. 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 4. Push the latch plate into the buckle until it clicks. 6.
Seats and Restraints If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 3‑37 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
3-64 Seats and Restraints 2 NOTES
Storage Storage Storage Compartments Instrument Panel Storage . . . . Glove Box . . . . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . . . Armrest Storage . . . . . . . . . . . . . . Center Console Storage . . . . . . Floor Console Storage . . . . . . . . 4-1 4-1 4-1 4-1 4-1 4-2 Additional Storage Features Cargo Cover . . . . . . . . . . . . . . . . . . Cargo Tie Downs . . . . . . . . . . . . . Cargo Management System . . . . . . . . . . . . . . . . . . . . . .
4-2 Storage To open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest. Move the armrest all the way to the rear position, slide the cover back and remove the tray. { WARNING Never open more than one of the three latches at a time to help avoid personal injury and damage to the console. Floor Console Storage To access the upper storage area, press the upper button (B) and lift up.
Storage Additional Storage Features WARNING (Continued) Cargo Cover For vehicles with a cargo cover, it can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use. Cargo Tie Downs Four cargo tie-downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads.
4-4 Storage Roof Rack System { WARNING If something is carried on top of the vehicle that is longer or wider than the roof rack— like paneling, plywood, or a mattress— the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Never carry something longer or wider than the roof rack on top of the vehicle unless using a GM Certified accessory carrier.
Instruments and Controls Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls . . . . . . 5-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Windshield Wiper/Washer . . . . . 5-5 Rear Window Wiper/ Washer . . . . . . . . . . . . . . . . . . . . . . 5-6 Compass . . . . . . . . . . . . . . . . . . . . . 5-6 Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Power Outlets . . . . . . . . . . . . . . . . .
5-2 Instruments and Controls Vehicle Personalization Vehicle Personalization (With DIC Buttons) . . . . . . . . . . . . . . . 5-42 Universal Remote System Universal Remote System . . . 5-49 Universal Remote System Programming . . . . . . . . . . . . . . . 5-49 Universal Remote System Operation . . . . . . . . . . . . . . . . . . 5-53 Controls Do not adjust the steering wheel while driving. Steering Wheel Adjustment Power Tilt Wheel The steering wheel can be adjusted.
Instruments and Controls Push the control forward or rearward to move the steering wheel toward the front or rear of the vehicle. To set the memory position, see Vehicle Personalization (With DIC Buttons) on page 5‑42. w / x (Next / Previous): Steering Wheel Controls To select preset or favorite radio stations: Press to select preset or favorite radio stations, select tracks on a CD/ DVD, or to select tracks and navigate folders on an iPod® or USB device. .
5-4 Instruments and Controls To navigate folders on an iPod or USB device for vehicles without a navigation system: To navigate folders on an iPod or USB device for vehicles with a navigation system: 1. Press and hold w or x while listening to a song until the contents of the current folder display on the radio display. 1. Go to the Music Navigator by first touching the center touch screen folder button in the main audio page. 2. Press and hold x to go back to the previous folder list. 2.
Instruments and Controls Press ¨ to select a track or a folder when navigating folders on an iPod or USB device. For vehicles with a navigation system: 1. Press and hold ¨ until a beep is heard, to place the radio into SCAN mode, a station will play for five seconds before moving to the next station. Windshield Wiper/Washer The windshield wiper/washer lever is located on the left side of the steering column. Turn the band with the wiper symbol to control the windshield wipers.
5-6 Instruments and Controls ignition key must be in ACC/ ACCESSORY or ON/RUN for this to work. See Washer Fluid on page 10‑21 Windshield Washer Fluid . { WARNING In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. WASHER FLUID LOW ADD FLUID is displayed on the Driver Information Center (DIC) when the washer fluid is low. See Washer Fluid Messages on page 5‑41.
Instruments and Controls Compass variance is the difference between the earth's magnetic north and true geographic north. If the compass is not set to the zone where you live, the compass may give false readings. The compass must be set to the variance zone in which the vehicle is traveling. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following.
5-8 Instruments and Controls If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic CB or cell phone antenna mount, a magnetic emergency light, magnetic note pad holder, or any other magnetic item. Turn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass.
Instruments and Controls 5. To decrease the time or date, do one of the following: . . . © SEEK. Press s REV. Turn f counter-clockwise. Press To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1. Press G and then the pushbutton located under the forward arrow that displays on the radio screen until the time 12H (hour) and 24H (hour), and the date MM/DD (month and day) and DD/MM (day and month) displays. 2.
5-10 Instruments and Controls When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. The indicator light does not come on when the ignition is in LOCK/OFF or if no equipment is plugged into the outlet. Notice: Improper use of the power outlet can cause damage not covered by the vehicle warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Instruments and Controls The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: . Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. . Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc. See High Voltage Devices and Wiring on page 10‑30.
5-12 Instruments and Controls Instrument Cluster United States version shown, Canada similar
Instruments and Controls Speedometer Fuel Gage When the fuel tank is low on fuel, the FUEL LEVEL LOW message will appear on the Driver Information Center (DIC). For more information see Fuel System Messages on page 5‑36. The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer.
5-14 Instruments and Controls Engine Coolant Temperature Gage United States Canada This gage shows the engine coolant temperature. Under normal driving conditions the gage will read 210°F (100 °C) or less. If the gage pointer is near 260°F (125 °C), the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible.
Instruments and Controls Safety Belt Reminders Driver Safety Belt Reminder Light Passenger Safety Belt Reminder Light The driver safety belt reminder light on the instrument panel cluster. 5-15 as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt.
5-16 Instruments and Controls If the airbag readiness light stays on after the vehicle has been started or comes on when while driving, the airbag system may not work properly. Have the vehicle serviced right away. { WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
Instruments and Controls If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away.
5-18 Instruments and Controls If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction.
Instruments and Controls An emission system malfunction might be corrected. . . Make sure the fuel cap is fully installed. See Filling the Tank on page 9‑41. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.
5-20 Instruments and Controls the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/ retailer can prepare the vehicle for inspection.
Instruments and Controls Antilock Brake System (ABS) Warning Light United States Canada The ABS warning light comes on briefly when the ignition key is turned to ON/RUN. This is normal. If the light does not come on then, have it fixed so it will be ready to warn you if there is a problem. Then start the engine again to reset the system. If the light still stays on, or comes on again while driving, the vehicle needs service.
5-22 Instruments and Controls Engine Coolant Temperature Warning Light Stop the vehicle and turn off the engine to avoid damage to the engine. A warning chime sounds when this light is on. When the Light is On Steady See Engine Overheating on page 10‑18 for more information. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Tire Messages on page 5‑39 for more information.
Instruments and Controls Engine Oil Pressure Light 5-23 Security Light { WARNING Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil.
5-24 Instruments and Controls See Headlamp High/Low-Beam Changer on page 6‑2 for more information. Cruise Control Light Information Displays Driver Information Center (DIC) (With DIC Buttons) Fog Lamp Light If your vehicle has DIC buttons, the information below explains the operation of this system. This light comes on whenever the cruise control is set. The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off.
Instruments and Controls The outside air temperature and compass, if equipped, also display on the DIC when viewing the trip and fuel information. The outside air temperature automatically appears in the top right corner of the DIC display. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced. The compass will be shown in the bottom right corner of the DIC display.
5-26 Instruments and Controls will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under Engine Oil Messages on page 5‑36. You should change the oil as soon as you can. See Engine Oil on page 10‑8. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual.
Instruments and Controls If a low tire pressure condition is detected by the system while driving, a message advising you add air to a specific tire will appear in the display. See Tire Pressure on page 10‑43 and Tire Messages on page 5‑39 for more information. To match an RKE transmitter to your vehicle: If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service. 2.
5-28 Instruments and Controls Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items: ODOMETER Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see “UNITS” earlier in this section.
Instruments and Controls The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the fuel tank.
5-30 Instruments and Controls Driver Information Center (DIC) (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster. Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages.
Instruments and Controls For example, if the vehicle was driven 5 miles (8 km) before it is started again, and then the retro-active reset feature is activated, the display will show 5 miles (8 km). As the vehicle begins moving, the display will then increase to 5.1 miles (8.2 km), 5.2 miles (8.4 km), etc.
5-32 Instruments and Controls RELEARN REMOTE KEY To access this display, the vehicle must be in P (Park). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. To match an RKE transmitter to your vehicle: 1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays. 2.
Instruments and Controls Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
5-34 Instruments and Controls Brake System Messages Door Ajar Messages LEFT REAR DOOR OPEN SERVICE BRAKE SYSTEM DRIVER DOOR OPEN This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 5‑20. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display.
Instruments and Controls RIGHT REAR DOOR OPEN This message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. Engine Cooling System Messages ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature.
5-36 Instruments and Controls Engine Oil Messages CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System on page 10‑10 for information on how to reset the message. See Engine Oil on page 10‑8 and Scheduled Maintenance on page 11‑2 for more information. possible. Do not drive the vehicle until the cause of the low oil pressure is corrected.
Instruments and Controls TIGHTEN GAS CAP This message may display along with the check engine light on the instrument panel cluster if the vehicle's fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 5‑17. Reinstall the fuel cap fully. See Filling the Tank on page 9‑41. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
5-38 Instruments and Controls Press the set/reset button or the trip odometer reset stem to acknowledge this message and clear it from the DIC display. For more information see Ultrasonic Parking Assist on page 9‑32. there is a problem. See your dealer/ retailer for service. The vehicle is safe to drive, however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.
Instruments and Controls THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Anti-Theft Alarm System on page 2‑13 for more information. Service Vehicle Messages SERVICE A/C (Air Conditioning) SYSTEM This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working.
5-40 Instruments and Controls Driver Information Center (DIC) (Without DIC Buttons) on page 5‑30. SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5‑22. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10‑46 for more information.
Instruments and Controls SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer/retailer for service. TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty.
5-42 Instruments and Controls Vehicle Personalization To change customization preferences, use the following procedure. Vehicle Personalization (With DIC Buttons) Entering the Feature Settings Menu Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
Instruments and Controls Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESPANOL: All messages will appear in Spanish. NO CHANGE: No change will be made to this feature. The current setting will remain.
5-44 Instruments and Controls DRIVER IN PARK: Only the driver's door will unlock when the vehicle is shifted into P (Park) . ALL AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition. ALL IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC.
Instruments and Controls 5-45 lock button on the RKE transmitter twice. See Delayed Locking on page 2‑7 for more information. is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC. Press the customization button until DELAY DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature.
5-46 Instruments and Controls APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Instruments and Controls Press the customization button until PARK TILT MIRRORS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse). DRIVER MIRROR: The driver's outside mirror will be tilted down when the vehicle is shifted into R (Reverse).
5-48 Instruments and Controls Press the customization button until MEMORY SEAT RECALL appears on the DIC display. Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No remote memory seat recall will occur. ON: The driver's seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed.
Instruments and Controls To select a setting, press the set/ reset button while the desired setting is displayed on the DIC. EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until FEATURE SETTINGS PRESS V TO EXIT appears in the DIC display. Press the set/reset button once to exit the menu. If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu.
5-50 Instruments and Controls Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you with programming the Universal Home Remote.
Instruments and Controls 2. Hold the end of your hand-held transmitter about 3 to 8 cm (1 to 3 inches) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button.
5-52 Instruments and Controls 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, selected in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it.
Instruments and Controls Universal Remote System Operation To erase all programmed buttons on the Universal Remote device: Reprogramming a Single Universal Remote Button To reprogram any of the three Universal Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. Using Universal Remote Press and hold the appropriate Universal Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted.
5-54 Instruments and Controls 2 NOTES
Lighting Lighting Exterior Lighting Exterior Lamp Controls . . . . . . . . 6-1 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . 6-3 Daytime Running Lamps (DRL)/Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-3 Delayed Headlamps . . . . . . . . . . 6-3 Hazard Warning Flashers . . . . . 6-4 Turn and Lane-Change Signals . . . . . . . . . . . . . . . . . . . . . . 6-4 Fog Lamps . . . . . . . . . . . . . . . . .
6-2 Lighting It controls the following systems: ; (Parking Lamps): Turns on the parking lamps together with the following: . Headlamps . Taillamps . . Parking Lamps Taillamps . . License Plate Lamps License Plate Lamps . . Instrument Panel Lights Instrument Panel Lights . Fog Lamps (If Equipped) The exterior lamps control has four positions: O (Off): Turns the automatic light control on or off.
Lighting Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low-beam position, pull the turn signal lever toward you to momentarily switch to high-beams. The DRL system makes either the low-beam headlamps come on at a reduced brightness or the DRL lights, for vehicles with High Intensity Discharge (HID) headlamps when the following conditions are met: . The ignition is in the ON/RUN position.
6-4 Lighting If the ignition is turned off with the exterior lamp control in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. Turn and Lane-Change Signals To disable the delayed headlamps feature or change the time of delay, see Vehicle Personalization (With DIC Buttons) on page 5‑42. The lever returns to its starting position whenever it is released.
Lighting Fog Lamps # (Fog Lamps): For vehicles with fog lamps, the button is located on the exterior lamps control. The exterior lamps control is on the instrument panel to the left of the steering column. The ignition must be in the ON/RUN position for the fog lamps to come on. Press # to turn the fog lamps on or off. A light will come on in the instrument panel cluster. When the headlamps are changed to high-beam, the fog lamps also go off.
6-6 Lighting The lamps can also be turned on and off by turning the instrument panel brightness control clockwise to the farthest position. Lighting Features Dome Lamp Override For vehicles with courtesy lamps, they come on and stay on for a set time whenever the unlock symbol is pressed on the Remote Keyless Entry (RKE) transmitter, if the vehicle has one. The dome lamp override button is next to the exterior lamps control.
Lighting Delayed Exit Lighting Parade Dimming Delayed exit lighting illuminates the interior for a period of time after the key is removed from the ignition. This feature automatically prohibits the dimming of the instrument panel displays in daylight while the headlamps are on so that the displays are still able to be seen. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination activates and remains on until one of the following occurs: .
6-8 Lighting EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver.
Infotainment System Infotainment System Introduction Introduction . . . . . . . . . . . . . . . . . . . 7-1 Theft-Deterrent Feature . . . . . . . 7-2 Operation . . . . . . . . . . . . . . . . . . . . . 7-2 Radio AM-FM Radio . . . . . . . . . . . . . . . . . 7-6 Satellite Radio . . . . . . . . . . . . . . . . 7-7 Radio Reception . . . . . . . . . . . . . 7-11 Multi-Band Antenna . . . . . . . . . . 7-11 Audio Players CD Player . . . . . . . . . . . . . . . . . . . CD/DVD Player . . . . . . . . . . . . . .
7-2 . Infotainment System Set up the tone, speaker adjustments, and preset radio stations. Operation For more information, see Defensive Driving on page 9‑2. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9‑17 for more information. Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual.
Infotainment System 7-3 System on page 7‑35 for more information on the vehicle's RSE system. The DVD player is the top slot on the radio faceplate. The player is capable of reading the DTS programmed DVD Audio or DVD Video media. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
7-4 Infotainment System prevents the rear seat occupant from operating the Rear Seat Audio (RSA) system or remote control. A lock symbol displays next to the clock display while the parental control feature is being used. The feature remains on until O is pressed and held for more than two seconds, or the driver turns the ignition off and exits the vehicle. 4 (Information): Press to switch the display between the radio station frequency and the time.
Infotainment System Setting the Tone (Bass/ Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust bass, midrange, or treble: 1. Press f until the tone control tabs display. 2. Continue pressing f to highlight the tab, or press the softkey under the tab. 3. To adjust the highlighted setting, do one of the following until the levels are obtained. . Turn f clockwise or counterclockwise. . Press \ FWD, or s REV. If a station's frequency is weak or if there is static, decrease the treble.
7-6 Infotainment System To quickly adjust all speaker and tone controls to the middle position, press f for more than two seconds until a beep sounds. Radios with CD and DVD fade differently depending on the DVD Media type: . . With DVD-A 5.1 Surround media, the left front and right front speakers fade rearward, leaving the center front speakers unaffected until the last fade step, then all front speakers mute. With DVD-V 5.
Infotainment System © SEEK ¨ : Press to go to the previous or to the next station and stay there. To scan stations, press and hold © or ¨ until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band.
7-8 Infotainment System commercial-free music, coast-to-coast, and in digital-quality sound. For more information, contact XM at www.xmradio.com or call 1-800-929-2100 in the U.S. and www.xmradio.ca or call 1-877-438-9677 in Canada. Finding a Category (CAT) Station CAT (Category): The CAT button is used to find XM™ stations when the radio is in the XM mode. To find XM channels within a desired category: Finding a Station 1. Press BAND until the XM frequency displays.
Infotainment System 4. Press the softkey under the Remove tab until the category name along with the word Removed displays. 5. Repeat the steps to remove more categories. Removed categories can be restored by pressing the softkey under the Add tab when a removed category is displayed or by pressing the softkey under the Restore All tab. Categories cannot be removed or added while the vehicle is moving faster than 8 km/h (5 mph).
7-10 Infotainment System XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return. If this station was one of the presets, choose another station for that preset button.
Infotainment System Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. FM FM signals only reach about 16 to 65 km (10 to 40 miles).
7-12 Infotainment System Audio Players CD Player Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. Z EJECT : Press and release to eject the disc that is currently playing. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The disc can be removed. If the disc is not removed, after several seconds, the disc automatically pulls back into the player.
Infotainment System surface of a CD is damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge. If the surface of a CD is soiled, take a soft, lint free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it.
7-14 Infotainment System . There could have been a problem while burning the CD. . The label could be caught in the CD player. If the CD is not playing correctly for any other reason, try a known good CD. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. If the radio displays an error message, write it down and provide it to your dealer/retailer when reporting the problem.
Infotainment System If either arrow is held, or pressed multiple times, the player continues moving backward or forward through the tracks on the CD. s REV (Fast Reverse): Press and hold to reverse playback quickly within a track. Sound will be heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. BAND: Press to listen to the radio when a CD or DVD is playing. The CD or DVD remains inside the radio for future listening or for viewing entertainment.
7-16 Infotainment System damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge. If the surface of a CD is soiled, take a soft, lint free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it.
Infotainment System on how to play an MP3/WMA CD-R or CD-RW disc, see MP3 (Radio with CD and Radio with CD/USB) on page 7‑21 or MP3 (Radio with CD/DVD) on page 7‑27. CD Messages Optical Error: The disc was inserted upside down. Disk Read Error: A disc was inserted with an invalid or unknown format. Player Error: There are disc LOAD or disc EJECT problems. . . It is very hot. When the temperature returns to normal, the CD should play. The road is very rough.
7-18 Infotainment System and the DVD. Also, see “Setting the Clock” in the index, for setting the clock and date. © SEEK (Previous Track/ Chapter): Press to return to the start of the current track or chapter. Press © again to go to the previous track or chapter. This button may not work when the DVD is playing the copyright information or the previews. SEEK ¨ (Next Track/Chapter): Press to go to the next track or chapter.
Infotainment System 7-19 30 seconds. If the DVD does not begin playing the movie automatically, press the softkey under the play/pause icon displayed on the radio. If the DVD still does not play, refer to the on-screen instructions, if available. q (Return): Press to exit the current active menu and return to the previous menu. This button operates only when a DVD is playing and a menu is active.
7-20 Infotainment System Inserting a Disc Stopping and Resuming Playback To play a disc, gently insert the disc, with the label side up, into the loading slot. The DVD player might not accept some paper labeled media. The player starts loading the disc into the system and shows “Loading Disc” on the radio display. At the same time, the radio displays a softkey menu of option(s).
Infotainment System DVD Error Messages Player Error: This message displays when there are disc load or eject problems. 64 kbps, 80 kbps, 96 kbps, 112 kbps, 128 kbps, 160 kbps, 192 kbps, 224 kbps, 256 kbps, and 320 kbps or a variable bit rate. Disc Format Error: This message displays, if the disc is inserted with the disc label wrong side up, or if the disc is damaged. Radios that have a USB port can play .mp3 and .
7-22 Infotainment System Root Directory The root directory of the disc is treated as a folder. If the root directory has compressed audio files, the directory displays on the radio as the CD label. If a disc contains both uncompressed CD audio and MP3/WMA files, a folder under the root directory called CD accesses all of the CD audio tracks on the disc. Empty Folder Folders that do not contain files are skipped, and the player advances to the next folder that contains files.
Infotainment System Playing a CD-R or CD-RW MP3 f (Tune): Turn to select MP3/WMA files. © SEEK: Press to go to the start of the track, if more than ten seconds have played. Press and hold or press multiple times to continue moving backward through tracks. ¨ SEEK: Press to go to the next track. Press and hold or press multiple times to continue moving forward through tracks. s REV (Reverse): Press and hold to reverse playback quickly.
7-24 Infotainment System The album name displays on the second line between the arrows and songs from the current album begins to play. Once all songs from that album have played, the player moves to the next album in alphabetical order on the CD and begins playing MP3 files from that album. connector and connect the other end to the USB port located in the center console.
Infotainment System \ FWD (Fast Forward): Press and hold to advance playback quickly. Sound is heard at a reduced volume. Release \ FWD to resume playing. The elapsed time of the file displays. 4 (Information): Press to display additional information about the selected track. Using Softkeys to Control a USB Storage Device or iPod The five softkeys below the radio display are used to control the functions listed below. To use the softkeys: 1.
7-26 Infotainment System h (Music Navigator): Press the softkey below h to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: . Playlists . Artists . Albums . Genres . Songs . Composers To select files: 1. Press the softkey below h. 2. Turn f to scroll through the list of menus. f to select the menu. Turn f to scroll through the 3. Press 4. folders or files in the selected menu. 5. Press f to select the file to be played.
Infotainment System MP3 (Radio with CD/DVD) Format The radio can play .mp3 or .wma files that were recorded onto a CD-R or CD-RW disc. The USB port can play .mp3 and .wma files that are stored on a USB storage device as well as AAC files that are stored on an iPod®. Compressed Audio or Mixed Mode Discs The radio plays discs that contain both uncompressed CD audio and MP3/WMA files depending on which slot the disc is loaded into.
7-28 Infotainment System Root Directory The root directory of the disc is treated as a folder. If the root directory has compressed audio files, the directory displays as F1 ROOT on the radio. If a disc contains both uncompressed CD audio and MP3/ WMA files, a folder under the root directory called CD accesses all of the CD audio tracks on the disc. Empty Folder Folders that do not contain files are skipped, and the player advances to the next folder that contains files.
Infotainment System Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed, however, they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song files. Playlists that have an .m3u or .pls file extension and are stored on a USB device may be supported by the radio with a USB port.
7-30 Infotainment System The album name displays on the second line between the arrows and songs from the current album begins to play. Once all songs from that album have played, the player moves to the next album in alphabetical order on the CD and begins playing MP3 files from that album. connector and connect the other end to the USB port located in the center console.
Infotainment System Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio’s display. f (Tune): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played. Press and hold or press multiple times to continue moving backward through tracks. ¨ SEEK: Press to go to the next track.
7-32 Infotainment System 4. Turn f to scroll through the files in the selected folder. h (Music Navigator): Press the softkey below h to view and 5. Press f to select the file to be played. select a file on an iPod, using the iPod's menu system. Files are sorted by: To skip through large lists, the five softkeys can be used to navigate in the following order: . Playlists . Artists . First softkey, first item in the list. . Albums .
Infotainment System ' (Repeat Track): Press the softkey below ' to repeat one track. The tab appears raised when Repeat Track is being used. Shuffle Functionality To use Shuffle: Press the softkey below > , 2 , < or = to select between Shuffle Off, Shuffle All Songs/ Shuffle Songs, Shuffle Album, or Shuffle Folder. > (Shuffle Off): This is the default mode when a USB storage device or iPod is first connected. 2 (Shuffle All Songs / Shuffle Songs): Shuffles all songs on the USB storage device or iPod.
7-34 Infotainment System DVD/CD AUX (Auxiliary): Press to select between DVD, CD, or Auxiliary. . . . . If an auxiliary input device is not connected, “No Aux Input Device” displays. When a disc is in either slot, the DVD/CD text tab and a message showing the track or chapter number displays. If an auxiliary input device is not connected, and a disc is in both the DVD slot and the CD slot the DVD/CD AUX button only cycles between the two sources and does not indicate “No Aux Input Device”.
Infotainment System Rear Seat Infotainment Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle's audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control. See Operation on page 7‑2 for more information on the vehicle's audio/DVD system.
7-36 Infotainment System The headphones may automatically turn off after four hours of continuous use. on the upper right side, above the ear pad and should be positioned on the right ear. Battery Replacement To adjust the volume on the headphones, use the volume control located on the right side. Notice: Do not store the headphones in heat or direct sunlight. This could damage the headphones and repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries.
Infotainment System Audio/Video (A/V) Jacks The A/V jacks are color coded to match typical home entertainment system equipment. The yellow jack (A) is for the video input. The white jack (B) is for the left audio input. The red jack (C) is for the right audio input. Power for auxiliary devices is not supplied by the radio system.
7-38 Infotainment System The RSE system always transmits the audio signal to the wireless headphones, if there is audio available. See “Headphones” earlier in this section for more information. The DVD player is capable of outputting audio to the wired headphone jacks on the RSA system, if the vehicle has this feature. The DVD player can be selected as an audio source on the RSA system. See Rear Seat Audio (RSA) System on page 7‑43 for more information.
Infotainment System If a CD or DVD is in the Radio DVD slot, the remote control O button can be used to turn on the video screen display and start the disc. The radio can also turn on the video screen display. See Operation on page 7‑2 for more information. Notice: Storing the remote control in a hot area or in direct sunlight can damage it, and the repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries. Keep the remote control stored in a cool, dry place.
7-40 Infotainment System t (Previous Track/Chapter): Press to return to the start of the current track or chapter. Press again to go to the previous track or chapter. This button might not work when the DVD is playing the copyright information or the previews. [ (Fast Forward): u (Next Track/Chapter): Press to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews.
Infotainment System Battery Replacement To change the remote control batteries: 1. Slide the rear cover back, on the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment. 3. Replace the battery cover. If the remote control is to be stored for a long period of time, remove the batteries and keep them in a cool, dry place.
7-42 Infotainment System Tips and Troubleshooting Chart (cont'd) DVD Display Error Messages Problem Recommended Action After stopping the player, I push Play but sometimes the DVD starts where I left off and sometimes at the beginning. If the stop button was pressed one time, the DVD player resumes playing where the DVD was stopped. If the stop button was pressed two times the DVD player begins to play from the beginning of the DVD.
Infotainment System DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. *Excludes the OnStar® System. Cleaning the RSE Overhead Console When cleaning the RSE overhead console surface, use only a clean cloth dampened with clean water.
7-44 Infotainment System inactive, with some radios, if the front seat passengers are listening to the radio. While listening to a disc, press ¨ to go to the next track or chapter on the disc. Press © to go back to the start of the current track or chapter (if more than ten seconds have played). This function is inactive, with some radios, if the front seat passengers are listening to the disc. P (Power): Press to turn the RSA on or off.
Infotainment System When a CD or DVD audio disc is playing, press PROG to go to the beginning of the CD or DVD audio. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a disc is playing in the CD or DVD changer, press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc.
7-46 Infotainment System Bluetooth Controls Pairing Information: Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Steering Wheel Controls on page 5‑3 for more information. . Up to five cell phones can be paired to the in-vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in-vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
Infotainment System 5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press and hold b g for two seconds.
7-48 Infotainment System Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: . Store . Digit Store . Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 3. Say the complete phone number to be stored at once with no pauses. .
Infotainment System 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . . If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time and the system will repeat them. 4. After the complete number has been entered, say “Store”.
7-50 Infotainment System 3. Say the name tag to be deleted. The system responds with “Would you like to delete, ? Please say yes or no”. . . If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting , returning to the main menu.” If the name tag is incorrect, say “No”. The system responds with “No. OK, let's try again, please say the name tag.
Infotainment System . If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number to be re-entered. Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Dial”.
7-52 Infotainment System Using the Re-dial Command Call Waiting Three-Way Calling 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 2. After the tone, say “Re-dial”.
Infotainment System Muting a Call Transferring a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Mute a call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Mute Call”. The system responds with “Call muted”. To Cancel Mute 1. Press b g . The system responds with “Ready” followed by a tone. 2.
7-54 Infotainment System Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Voice”.
Infotainment System Sending a Stored Name Tag During a Call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. 3. Say the name tag to send. . . If the system clearly recognizes the name tag it responds with “OK, Sending ” and the dial tones are sent and the call continues.
7-56 Infotainment System 2 NOTES
Climate Controls 8-1 Climate Controls Climate Control Systems Climate Control Systems The heating, cooling, and ventilation in the vehicle can be controlled with this system. Climate Control Systems . . . . . . 8-1 Dual Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 8-4 Rear Climate Control System (Rear Climate Control Only) . . . . . . . . . . . . . . . 8-10 Rear Climate Control System (Rear Climate with Rear Seat Audio) . . . . . . . . . . . . . . . . . . . . . .
8-2 Climate Controls 9 (Off): Turn the fan control all the way counterclockwise to turn the front climate control system off. 9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system. Air Delivery Mode Control: Turn clockwise or counterclockwise to change the current airflow mode.
Climate Controls For quicker cool down on hot days: 1. Open the windows to let hot air escape. H mode. Select # . 2. Select 3. 4. Select the coolest temperature. 5. Select the highest fan speed. 6. Close the windows after the hot air has escaped. 7. Once the vehicle's interior temperature is below the outside temperature, select @ mode for faster cooling. Using recirculation for long periods of time could cause the air inside of the vehicle to become too dry.
8-4 Climate Controls Do not drive the vehicle until all the windows are clear. For vehicles with heated outside rearview mirrors, fog or frost is cleared from the surface of the mirror when < is pressed. Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. Notice: Do not use anything sharp on the inside of the rear window.
Climate Controls Display Function Automatic Operation Each time the temperature, mode, or fan control buttons are pressed, the climate control display shows that function along with the inside temperature setting. The outside temperature is displayed on the instrument panel cluster. AUTO (Automatic): The system automatically controls the inside temperature, the air delivery, and the fan speed. O (On/Off): Press to turn the climate control system on or off.
8-6 Climate Controls Temperature Control The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system. The temperature can be adjusted even if the system is turned off since outside air still enters the vehicle, unless the recirculation mode is selected. See “Recirculation” later in this section. Driver Side Temperature Control: Press the + or − buttons to increase or decrease the driver side temperature.
Climate Controls - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is less than 4°C (40°F). Do not drive the vehicle until all the windows are clear. 0 (Defrost): Press to turn the defrost on or off. This mode quickly clears the windshield of fog or frost.
8-8 Climate Controls The air conditioning system removes moisture from the air, so water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re-selected when the engine is turned on again.
Climate Controls Sensors The solar sensor, located in the defrost grille in the middle of the instrument panel, monitors the solar heat. Do not cover the solar sensor or the system will not work properly. 8-9 There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature.
8-10 Climate Controls Rear Climate Control System (Rear Climate Control Only) Independent Mode: This mode directs rear seating airflow according to the settings of the rear controls. It comes on when any rear control is adjusted. Fan Control: Turn clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 9 to turn the fan off. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the airflow temperature. A. Fan Control B. Temperature Control C.
Climate Controls Rear Climate Control System (Rear Climate with Rear Seat Audio) 8-11 Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Independent Mode: This mode directs rear seating airflow according to the settings of the rear controls. It comes on when any rear control is adjusted. D C (Fan Control): Press the fan up or down buttons to increase or decrease the fan speed. A. Fan Control B. Air Delivery Mode Control C.
8-12 Climate Controls N (Air Delivery Mode Control): Press to manually change the direction of the airflow. Repeatedly press the button until the desired mode appears on the display. H (Vent): Air is directed through the overhead outlets. Air Vents Use the slider switch in the center of the outlet, to change the direction of the air flow. Use the thumbwheel near the outlet to control the amount of air flow or to shut off the airflow.
Driving and Operating Driving and Operating Shifting Into Park . . . . . . . . . . . . 9-19 Shifting Out of Park . . . . . . . . . . 9-20 Parking Over Things That Burn . . . . . . . . . . . . . . . . . . 9-21 Engine Exhaust Driving Information Defensive Driving . . . . . . . . . . . . . 9-2 Drunk Driving . . . . . . . . . . . . . . . . . 9-2 Control of a Vehicle . . . . . . . . . . . 9-3 Braking . . . . . . . . . . . . . . . . . . . . . . . 9-3 Steering . . . . . . . . . . . . . . . . . . . . . . .
9-2 Driving and Operating Driving Information Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 3‑14. { WARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: . Allow enough following distance between you and the driver in front of you. .
Driving and Operating Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking. Control of a Vehicle The following three systems help to control the vehicle while driving — brakes, steering, and accelerator.
9-4 Driving and Operating If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push.
Driving and Operating Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
9-6 Driving and Operating The three types of skids correspond to the vehicle's three control systems. In the braking skid, the wheels are not rolling. In the steering or cornering skid, too much speed or steering in a curve causes tires to slip and lose cornering force. And in the acceleration skid, too much throttle causes the driving wheels to spin. If the vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go.
Driving and Operating Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle's tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. There is no hard and fast rule about hydroplaning. The best advice is to slow down when the road is wet. . Have good tires with proper tread depth. See Tires on page 10‑37. . Turn off cruise control.
9-8 Driving and Operating { WARNING Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have the engine running and the vehicle in gear when going downhill. . Stay in your own lane. Do not swing wide or cut across the center of the road.
Driving and Operating Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 13‑5. To get help and keep everyone in the vehicle safe: . Turn on the hazard warning flashers. . Tie a red cloth to an outside mirror. WARNING (Continued) If the vehicle is stuck in the snow: . . Check again from time to time to be sure snow does not collect there. .
9-10 Driving and Operating feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed. This keeps the battery charged to restart the vehicle and to signal for help with the headlamps. Do this as little as possible to save fuel.
Driving and Operating { WARNING Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle. Tire and Loading Information Label 9-11 seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
9-12 Driving and Operating Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Driving and Operating 9-13 seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle's capacity weight. Certification/Tire Label Example 2 A. Vehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). C. Available Cargo Weight = 113 kg (250 lbs). Example 3 A. Vehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs). B.
9-14 Driving and Operating The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer/retailer can help you with this. Be sure to spread out your load equally on both sides of the centerline.
Driving and Operating WARNING (Continued) . Do not leave an unsecured child restraint in your vehicle. . When you carry something inside the vehicle, secure it whenever you can. . Do not leave a seat folded down unless you need to. Starting and Operating . Avoid making hard stops for the first 322 km (200 miles) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement.
9-16 Driving and Operating Ignition Positions and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. ( (LOCK/OFF): This position locks the ignition and transmission. The key can be removed in LOCK/OFF. The shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF. The ignition switch has four different positions. In order to shift out of P (Park), the ignition must be in ON/RUN or ACC/ ACCESSORY and the brake pedal must be applied.
Driving and Operating Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the ignition key is turned off: . Audio System . Power Windows . Sunroof (if equipped) Power to the windows and sunroof will work up to 10 minutes or until a door is opened. The radio continues to work for 10 minutes or until the driver's door is opened. For an additional 10 minutes of operation, close all the doors and turn the key to ON/RUN and then back to LOCK/OFF.
9-18 Driving and Operating 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator.
Driving and Operating { WARNING Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts.
9-20 Driving and Operating you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without first pushing the button. Shifting Out of Park If you can, it means that the shift lever was not fully locked in P (Park). . Torque Lock Torque lock is when the weight of the vehicle puts too much force on the parking pawl in the transmission.
Driving and Operating Parking Over Things That Burn { WARNING Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { WARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: .
9-22 Driving and Operating Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation.
Driving and Operating { WARNING It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park).
9-24 Driving and Operating D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: Manual Mode . Going less than 56 km/h (35 mph), push the accelerator pedal about halfway down. . Going about 56 km/h (35 mph) or more, push the accelerator all the way down. ERS mode allows you to choose the top-gear limit of the transmission and the vehicle's speed while driving down hill or towing a trailer.
Driving and Operating Automatic Engine Grade braking is not available when the ERS is active. It is available in D (Drive) for both normal and Tow/Haul mode. While using the ERS, cruise control and the tow/haul mode can be used. See Tow/Haul Mode following. Tow/Haul Mode _ (Tow/Haul): The vehicle may have a Tow/Haul mode. The button is located on the instrument panel under the climate controls. Push the button to activate the system. Push it again to deactivate the system.
9-26 Driving and Operating Brakes Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal.
Driving and Operating Parking Brake To set the parking brake, hold the regular brake pedal down, then push the parking brake pedal down. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5‑20. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.
9-28 Driving and Operating Ride Control Systems StabiliTrak System The vehicle has the StabiliTrak system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you first start the vehicle and begin to drive away, the system performs several diagnostic checks to ensure there are no problems. The system may be heard or felt while it is working.
Driving and Operating when traction control is off, but will not be able to use the engine speed management system. See “Traction Control Operation” next for more information. When the traction control system has been turned off, system noises may be heard and felt as a result of the brake-traction control working.
9-30 Driving and Operating Setting Cruise Control Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. With cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph). The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
Driving and Operating 3. Press and release the SET– button located on the steering wheel. 4. Take your foot off the accelerator. Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged. But it does not need to be reset. Once the vehicle speed is 40 km/h (25 mph) or greater, press the +RES button on the steering wheel. The vehicle returns to the previously set speed and stays there.
9-32 Driving and Operating Ending Cruise Control There are three ways to end cruise control: Object Detection Systems . Step lightly on the brake pedal. Ultrasonic Parking Assist . Press the [ button. Press the T button. For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 8 km/h (5 mph), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 2.
Driving and Operating How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). A single tone sounds to indicate the system is working. URPA operates only at speeds less than 5 mph (8 km/h). An obstacle is indicated by audible beeps. The interval between the beeps becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm (12 in) the beeps are continuous. To be detected, objects must be at least 25.
9-34 Driving and Operating Rear Vision Camera (RVC) The vehicle may have a Rear Vision Camera system. Read this entire section before using it. { WARNING The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: . Detect objects that are outside the camera's field of view, below the bumper, or underneath the vehicle. . Detect children, pedestrians, bicyclists, or pets.
Driving and Operating Vehicles With Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into R (Reverse), the video image automatically appears on the navigation screen. Once the driver shifts out of R (Reverse), the navigation screen will go back to the last screen that had been displayed, after a delay.
9-36 Driving and Operating _ (Contrast) : Touch the + (plus) or – (minus) screen buttons to increase or decrease the contrast of the screen. Symbols The navigation system may have a feature that lets the driver view symbols on the navigation screen while using the rear vision camera. The Ultrasonic Rear Park Assist (URPA) system must not be disabled to use the caution symbols.
Driving and Operating 9-37 When the System Does Not Seem To Work Properly The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance.
9-38 . . Driving and Operating The back of the vehicle is in an accident, the position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your dealer/retailer. There are extreme temperature changes. The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will flash. .
Driving and Operating Recommended Fuel Use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. If heavy knocking is heard when using gasoline rated at 87 octane or higher, the engine needs service.
9-40 Driving and Operating Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.
Driving and Operating Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol.
9-42 Driving and Operating To open the fuel door, push the rearward center edge in and release and it will open. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door. { WARNING Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned.
Driving and Operating Filling a Portable Fuel Container WARNING (Continued) . { WARNING Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: . Dispense fuel only into approved containers. .
9-44 Driving and Operating vehicle — such as a motorhome, see Recreational Vehicle Towing on page 10‑83. Driving Characteristics and Towing Tips { WARNING The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured.
Driving and Operating . Obey speed limit restrictions when towing a trailer. . The vehicle is designed primarily as a passenger and load carrying vehicle. If a trailer is towed, the vehicle will require more frequent maintenance due to the additional load. Driving with a Trailer Towing a trailer requires experience. Get familiar with handling and braking with the added trailer weight. The vehicle is now longer and not as responsive as the vehicle is by itself.
9-46 Driving and Operating Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle's Gross Combined Weight Rating (GCWR). See Trailer Towing on page 9‑48. Tow/Haul is most useful when pulling a heavy trailer or a large or heavy load under the following driving conditions: . Travelling through rolling terrain. . Travelling in stop and go traffic. .
Driving and Operating When towing a trailer, the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out. Check occasionally to be sure the trailer bulbs are still working. Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. The vehicle can tow in D (Drive).
9-48 Driving and Operating 3. Drive slowly until the trailer is clear of the chocks. Engine Cooling When Trailer Towing Weight of the Trailer 4. Stop and have someone pick up and store the chocks. The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating on page 10‑18. Speed, altitude, road grades, outside temperature, special equipment, and the amount of tongue weight the vehicle can carry must be considered.
Driving and Operating 9-49 Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options.
9-50 Driving and Operating If a weight-carrying hitch or a weight-distributing hitch is being used, the trailer tongue (A) should weigh 10-15 percent of the total loaded trailer weight (B). After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer. Trailering may be limited by the vehicle's ability to carry tongue weight.
Driving and Operating If the vehicle has many options and there is a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. 136 kg (300 lbs) could be added to the front axle weight and 181 kg (400 lbs) to the rear axle weight. The vehicle now weighs: Weight is still below 3 266 kg (7,200 lbs) and you might think 318 additional kilograms (700 lbs) should be subtracted from the trailering capacity to stay within GCWR limits.
9-52 Driving and Operating Towing Equipment Hitches Weight-Distributing Hitches and Weight Carrying Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. . . The rear bumper on the vehicle is not intended for hitches. Do not attach rental hitches or other bumper-type hitches to it. Use only a frame-mounted hitch that does not attach to the bumper.
Driving and Operating Trailer Wiring Harness Basic Trailer Wiring The trailer wiring harness, with a seven-pin connector, is located at the rear of the vehicle and is tied to the vehicle's frame. The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer/retailer. The seven-wire harness contains the following trailer circuits: . . Yellow: Left Stop/Turn Signal Dark Green: Right Stop/Turn Signal . Brown: Taillamps . Black: Ground .
9-54 Driving and Operating Conversions and Add-Ons Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/ retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle battery, even if the vehicle is not operating. The vehicle has an airbag system.
Vehicle Care Vehicle Care General Information General Information . . . . . . . . . . California Proposition 65 Warning . . . . . . . . . . . . . . . . . California Perchlorate Materials Requirements . . . . Accessories and Modifications . . . . . . . . . . . . . . . 10-2 10-3 10-3 10-3 Vehicle Checks Doing Your Own Service Work . . . . . . . . . . . . . . . 10-4 Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Engine Compartment Overview . . . . . . . . . . . . . . . . . . . 10-6 Engine Cover .
10-2 Vehicle Care Tire Inspection . . . . . . . . . . . . . . 10-49 Tire Rotation . . . . . . . . . . . . . . . 10-49 When It Is Time for New Tires . . . . . . . . . . . . . . . . . . . . . . 10-51 Buying New Tires . . . . . . . . . . . 10-51 Different Size Tires and Wheels . . . . . . . . . . . . . . . . . . . 10-53 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 10-53 Wheel Alignment and Tire Balance . . . . . . . . . . . . . . . . . . . 10-55 Wheel Replacement . . . . . . . .
Vehicle Care California Proposition 65 Warning Accessories and Modifications Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
10-4 Vehicle Care Vehicle Checks Doing Your Own Service Work { WARNING You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. . Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task. (Continued) WARNING (Continued) . Be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused.
Vehicle Care Hood To open the hood, do the following: 2. At the front of the vehicle, pull up on the center of the hood, and push the secondary hood release to the right. 3. After you have partially lifted the hood, gas struts will automatically take over to lift and hold the hood in the fully open position. 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver's side of the vehicle.
10-6 Vehicle Care Engine Compartment Overview
Vehicle Care A. Radiator Pressure Cap . See Cooling System on page 10‑14. B. Engine Coolant Recovery Cap. See Cooling System on page 10‑14. C. Remote Negative (−) Terminal. See Jump Starting on page 10‑78. D. Engine Compartment Fuse Block on page 10‑31. E. Remote Positive (+) Terminal. See Jump Starting on page 10‑78. F. Power Steering Reservoir and Cap (under engine cover). See Power Steering Fluid on page 10‑20. G. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 10‑8. H.
10-8 Vehicle Care Engine Oil When to Add Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10‑6 for the location of the engine oil dipstick. 1. Turn off the engine and give the oil several minutes to drain back into the oil pan.
Vehicle Care What Kind of Engine Oil to Use . GM6094M Use only an oil that meets GM Standard GM6094M. Look for three things: . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container.
10-10 Vehicle Care Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty. Engine Oil Life System When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter.
Vehicle Care If the vehicle does not have Driver Information Center (DIC) buttons: If the vehicle has Driver Information Center (DIC) buttons: 1. Turn the ignition to ON/RUN, with the engine off. The vehicle must be in P (Park) to access this display. Press the trip odometer reset stem until OIL LIFE REMAINING displays. 1. Turn the ignition to ON/RUN, with the engine off. 2. Press and hold the trip odometer reset stem until OIL LIFE REMAINING shows 100%.
10-12 Vehicle Care Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer/retailer and have it repaired as soon as possible. Change the fluid at the intervals listed in Scheduled Maintenance on page 11‑2, and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 11‑7.
Vehicle Care 2. Disconnect the cover fitting from the ventilation tube (A). 5. Loosen the six housing cover (C) screws (B). 3. Disconnect the wiring harness connector from the sensor (B). 6. Remove the housing cover (C) with outlet duct. 7. Remove the filter (D) and any loose debris that may be found in the base (E). 8. Inspect or replace the filter (D). 9. Reverse Steps 2 through 6 to reinstall the housing cover and reconnect the electrical connector to the sensor. 10. Reinstall the engine cover.
10-14 Vehicle Care Cooling System The cooling system allows the engine to maintain the correct working temperature. { WARNING An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { WARNING Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. A. Engine Coolant Recovery Tank B. Radiator Pressure Cap C.
Vehicle Care What to Use { WARNING Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned.
10-16 Vehicle Care the cooling system is cool before this is done. See Cooling System on page 10‑14 for more information. The coolant recovery tank cap has this symbol on it. When the engine is cold, the coolant level should be at or above the FULL COLD line marked on the recovery tank. When the engine is hot, the level could be higher than the FULL COLD line. If the coolant is below the FULL COLD line when the engine is hot, there could be a leak in the cooling system.
Vehicle Care WARNING (Continued) cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap. 10-17 2. Remove the radiator pressure cap when the cooling system, including the upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left in the system.
10-18 Vehicle Care Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. The vehicle has several indicators to warn of engine overheating. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.
Vehicle Care If Steam Is Coming From The Engine Compartment WARNING (Continued) See Overheated Engine Protection Operating Mode on page 10‑20 for information on driving to a safe place in an emergency. { WARNING Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
10-20 Vehicle Care If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode” next in this section. Overheated Engine Protection Operating Mode This emergency operating mode lets the vehicle be driven to a safe place in an emergency situation.
Vehicle Care The fluid level should be somewhere between MAX and MIN line on the dipstick in room temperature. If the fluid is on or below MIN line, you should add fluid close to MAX Line. What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11‑7. Always use the proper fluid. Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty.
10-22 Vehicle Care Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly. { WARNING The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced.
Vehicle Care Brake Fluid There are only two reasons why the brake fluid level in the reservoir might go down: . The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10‑6 for the location of the reservoir. . The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up. A fluid leak in the brake hydraulic system can also cause a low fluid level.
10-24 Vehicle Care What to Add damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11‑7. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Vehicle Care All-Wheel Drive It is not necessary to check the all–wheel drive lubricant levels. A fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer/retailer as soon as possible. Starter Switch Check { WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2.
10-26 Vehicle Care 3. With the engine off, turn the ignition to ON/RUN, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer/retailer for service. Park Brake and P (Park) Mechanism Check { WARNING When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged.
Vehicle Care Backglass Wiper Blade Headlamp Aiming To replace the backglass wiper blade: Headlamp aim has been preset at the factory and should need no further adjustment. 1. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle. 2. Press the button in the middle of the wiper arm connector and pull the wiper blade away from the arm connector. 3.
10-28 Vehicle Care Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑29. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs { WARNING Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
Vehicle Care 4. Remove the two hex nuts holding the taillamp assembly in place. License Plate Lamp 5. Pull out the taillamp assembly. 1. Remove the two screws holding each of the license plate lamps to the liftgate trim. 6. Turn the bulb socket counterclockwise and pull it straight out to remove it. To replace one of these bulbs: 10-29 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket. 4. Install the new bulb. 5.
10-30 Vehicle Care Electrical System High Voltage Devices and Wiring { WARNING Exposure to high voltage can cause shock, burns, and even death. The high voltage systems in your vehicle can only be serviced by technicians with special training. High voltage devices are identified by labels. Do not remove, open, take apart, or modify these devices. High voltage cable or wiring has orange covering. Do not probe, tamper with, cut, or modify high voltage cable or wiring.
Vehicle Care Fuses and Circuit Breakers Engine Compartment Fuse Block The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. The underhood fuse block is located in the engine compartment, on the passenger side of the vehicle. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
10-32 Vehicle Care Fuses Usage A/C CLUTCH Air Conditioning Clutch ABS MTR Antilock Braking System (ABS) Motor AFS AIRBAG Adaptive Forward Lighting System Airbag System AUX POWER Auxiliary Power AUX VAC PUMP Auxiliary Vacuum Pump AWD All-Wheel-Drive System BATT 1 Battery 1 BATT 2 Battery 2 BATT 3 Battery 3 ECM Engine Control Module ECM 1 Engine Control Module 1 EMISSION 1 Emission 1
Vehicle Care Fuses Usage EMISSION 2 Emission 2 EVEN COILS Even Injector Coils FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FOG LAMP FSCM HORN HTD MIR HVAC BLWR Fog Lamps Fuel System Control Module Fuses Usage LT TRLR STOP/TRN Trailer Left Stoplamp and Turn Signal ODD COILS Odd Injector Coils PCM IGN Powertrain Control Module Ignition RT PRK RVC SNSR Regulated Voltage Control Sensor S/ROOF/ Sunroof SUNSHADE Horn Power Outlet Heated Outside Rearview Mirror REAR CAMERA Rear Camera RR APO
10-34 Vehicle Care Fuses Usage TRLR PRK LAMP Trailer Parking Lamps TRLR PWR Trailer Power WPR/WSW Windshield Wiper/ Washer Relays HID/ LO BEAM HORN IGN Relays Usage A/C CMPRSR CLTCH Air Conditioning Compressor Clutch AUX VAC PUMP Auxiliary Vacuum Pump CRNK Switched Power FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FAN 3 Cooling Fan 3 FOG LAMP Fog Lamps HI BEAM High-Beam Headlamps Usage Relays Usage High Intensity Discharge (HID) Low-Beam Headlamps TRLR BCK/UP WPR Windshield Wip
Vehicle Care Fuses AIRBAG AMP BCK/ UP/STOP Amplifier Back-up Lamp/ Stoplamp Body Control Module CNSTR/ VENT Canister Vent DR/LCK DRL Fuses Usage HVAC Heating, Ventilation and Air Conditioning Airbag BCM CTSY Courtesy INADV/ PWR/LED Inadvertent Power LED INFOTMNT Infotainment LT/TRN/SIG Driver Side Turn Signal MSM Memory Seat Module PDM Power Mirrors, Liftgate Release Door Locks Daytime Running Lamps PWR MODE Power Mode DRL 2 GMC HID Only/ Rear Fog Lamps-China Only DSPLY Display
10-36 Vehicle Care Relays Usage LT/ PWR/SEAT Driver Side Power Seat Relay RT/ PWR/SEAT Passenger Side Power Seat Relay Power Windows PWR/WNDW Relay PWR/ COLUMN L/GATE LCK Liftgate Relay Power Lock Relay REAR/WSW Rear Window Washer Relay UNLCK Power Unlock Relay DRL2 LT/UNLCK Relay Side Power Steering Column Relay Daytime Running Lamps 2 Relay Driver Side Unlock Relay Relays DRL SPARE FRT/WSW Usage Daytime Running Lamps Relay Spare Front Windshield Washer Relay
Vehicle Care Wheels and Tires Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. WARNING (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure.
10-38 Vehicle Care and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Vehicle Care compact spare tire, see Compact Spare Tire on page 10‑77 and If a Tire Goes Flat on page 10‑57 . (C) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
10-40 Vehicle Care (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carry capacity a tire is certified to carry.
Vehicle Care Cold Tire Pressure: The amount of air pressure in a tire, measured in psi (pounds per square inch) or kPa (kilopascal) before a tire has built up heat from driving. See Tire Pressure on page 10‑43 . Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S.
10-42 Vehicle Care Occupant Distribution : Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Vehicle Care Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9‑10 . Tire Pressure Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size and recommended inflation pressure.
10-44 Vehicle Care For additional information regarding how much weight your vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9‑10 . How you load your vehicle affects vehicle handling and ride comfort. Never load your vehicle with more weight than it was designed to carry. When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. The compact spare should be at 60 psi (420 kPa).
Vehicle Care Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
10-46 Vehicle Care Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly, if the vehicle has one. The TPMS sensors monitor the air pressure in the vehicle's tires and transmits the tire pressure readings to a receiver located in the vehicle.
Vehicle Care Notice: Using non-approved tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use the GM approved tire sealant available through your dealer/ retailer. Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors.
10-48 . . Vehicle Care Replacement tires or wheels do not match your vehicle's original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Buying New Tires on page 10‑51. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction. If the TPMS is not functioning it cannot detect or signal a low tire condition.
Vehicle Care 5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position. 6. Proceed to the passenger side front tire, and repeat the procedure in Step 5. 7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5. 8.
10-50 Vehicle Care After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Tire Pressure on page 10‑43 and Vehicle Load Limits on page 9‑10 . Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑46 . When rotating the vehicle's tires, always use the correct rotation pattern shown here. If the vehicle has a compact spare tire, do not include it in the tire rotation.
Vehicle Care When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which appear when the tires have only 1.6 mm (1/16 inch) or less of tread remaining. The vehicle needs new tires if any of the following statements are true: . You can see the indicators at three or more places around the tire. .
10-52 Vehicle Care GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by an MS for mud and snow.
Vehicle Care Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed on your vehicle. Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 10‑44 . Your vehicle's original equipment tires are listed on the Tire and Loading Information Label.
10-54 Vehicle Care Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires.
Vehicle Care Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
10-56 Vehicle Care If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new Saturn original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. { WARNING Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control.
Vehicle Care WARNING (Continued) To help avoid damage to the vehicle, drive slowly, readjust or remove the device if it is contacting the vehicle, and do not spin the vehicle's wheels. If you do find traction devices that will fit, install them on the front tires. If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
10-58 Vehicle Care { WARNING WARNING (Continued) Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: To be certain the vehicle will not move, put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle. 3.
Vehicle Care Tire Sealant and Compressor Kit { WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9‑21.
10-60 Vehicle Care Tire Sealant This vehicle may have one of the following tire sealant and compressor kits. The kit includes: Read and follow the safe handling instructions on the label adhered to the sealant canister. A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Check the tire sealant expiration date on the sealant canister.
Vehicle Care 10-61 2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster. Always do a safety check first.
10-62 Vehicle Care 7. Start the vehicle. The vehicle must be running while using the air compressor. on the Tire and Loading Information label. See Tire Pressure on page 10‑43. 8. Turn the selector switch (A) counterclockwise to the Sealant + Air position. The pressure gage (C) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached. 9.
Vehicle Care 16. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister (E) and place it in a highly visible location. The label is a reminder not to exceed 55 mph (90 km/h) until the damaged tire is repaired or replaced. 17. Return the equipment to its original storage location in the vehicle. 18. Immediately drive the vehicle 5 miles (8 km) to distribute the sealant in the tire. 19.
10-64 Vehicle Care Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 10‑57. 1. Remove the tire sealant and compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑66. 2. Unwrap the air only hose (G) and the power plug (H). 3. Place the kit on the ground.
Vehicle Care 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑9. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.
10-66 Vehicle Care Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release button. 3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer/retailer. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. 5. Push the new canister into place.
Vehicle Care Tire Changing 4. Turn the jack on its side, with the bottom facing toward you. Removing Tools 5. Pull the jack straight out, bottom first. The tools needed to remove the spare tire are located in the storage compartment on the driver side, at the rear of the vehicle. 1. Open the jack storage compartment by pulling on the latch tab, located toward the rear of the vehicle, and pulling the cover off. 10-67 A. Tool Bag B. Wing Bolt C. Jack 2.
10-68 Vehicle Care Removing the Spare Tire E. Compact Spare Tire The compact spare tire is located under the vehicle, in front of the rear bumper. See Compact Spare Tire on page 10‑77 for more information about the compact spare. F. Retainer G. Hoist Shaft Assembly 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 2. Open the carpet cutout that is located through the hole of the storage compartment.
Vehicle Care 6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a flat road tire under the vehicle. See “Storing a Flat or Spare Tire and Tools” later in this section. To continue changing the flat tire, see “Removing the Flat Tire and Installing the Spare Tire” later in this section. Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2.
10-70 Vehicle Care If the vehicle has aluminum wheels, remove the wheel nut caps using the wheel wrench. Notice: If this vehicle has wheel locks and an impact wrench is used to remove the wheel nuts, the lock nut or wheel lock key could be damaged. Do not use an impact wrench to remove the wheel nuts if this vehicle has wheel locks. Notice: If a jack is used to raise the vehicle without positioning it correctly, the vehicle could be damaged.
Vehicle Care WARNING (Continued) To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle. clockwise in the jack. Raise the vehicle far enough off the ground so that there is enough room for the spare tire to fit under the wheel well. 8. Remove all the wheel nuts and the flat tire. 6. Attach the lug wrench to the jack, and turn the wrench clockwise to raise the jack head 3 inches (7.6 cm).
10-72 Vehicle Care 10. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. 11. Place the spare tire on the wheel mounting surface. 12. Put the nuts on by hand by turning them clockwise until the wheel is held against the mounting surface. Make sure the rounded end is toward the wheel. 13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely.
Vehicle Care Storing the Spare Tire { WARNING The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle. If this happened when the vehicle was being driven, the tire might contact a person or another vehicle, causing injury and damage to itself.
10-74 Vehicle Care 3. Put the flat tire in the rear storage area with the valve stem pointing toward the rear of the vehicle. 6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the lug wrench to tighten the cable. Storing the Flat Tire 1. Remove the cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 5.
Vehicle Care Storing the Tools 10-75 3. Reinstall the wing bolt (B) by turning clockwise. 4. To replace the cover, line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the cover closed. 8. Make sure the metal tube is centered at the striker. Push the tube toward the front of the vehicle. A. Tool Bag 9. Close the liftgate and make sure it is latched properly. C. Jack B.
10-76 Vehicle Care Secondary Latch System This vehicle has an underbody mounted tire hoist assembly that has a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down. See Tire Changing on page 10‑67 for instructions on storing the spare tire correctly.
Vehicle Care Have the hoist shaft assembly inspected as soon as you can. You will not be able to store a spare tire using the hoist assembly until it has been repaired or replaced. 5. Turn the lug wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released and the spare tire is balancing on the jack. Compact Spare Tire { WARNING 8.
10-78 Vehicle Care After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have the full-size tire repaired or replaced at your convenience. Of course, it is best to replace the spare with a full-size tire as soon as possible.
Vehicle Care Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle's system is not a 12-volt system with a negative ground, both vehicles can be damaged.
10-80 Vehicle Care { WARNING Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the batteries have enough water. You do not need to add water to the ACDelco® battery (or batteries) installed in your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first.
Vehicle Care 10-81 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
10-82 Vehicle Care 10. Now start the vehicle with the good battery and run the engine for a while. To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle.
Vehicle Care Towing Towing the Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes — such as behind a motorhome, see Recreational Vehicle Towing following. Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome.
10-84 Vehicle Care Dinghy Towing For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Re-install the fuse to start the vehicle. To tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle to be towed, shift the transmission to P (Park), and turn the ignition to LOCK/OFF.
Vehicle Care Once the destination is reached: 1. Set the parking brake. Dolly Towing (All-Wheel-Drive Vehicles) 2. Reinstall the 50 amp BATT1 fuse to the underhood fuse block. 10-85 Dolly Towing (Front-Wheel-Drive Vehicles Only) 3. Shift the transmission to P (Park), turn the ignition to LOCK/OFF and remove the key from the ignition. 4. Disconnect the vehicle from the towing vehicle.
10-86 Vehicle Care 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. Appearance Care 5. Remove the key from the ignition. Cleaning Exterior Lamps/ Lenses 6. Secure the vehicle to the dolly. Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing the Vehicle” later in this section. Exterior Care 7. Release the parking brake.
Vehicle Care Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible.
10-88 Vehicle Care Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes could cause water to enter the vehicle. Avoid using high pressure washes closer than 30 cm (12 inches) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals. Notice: Conveyor systems on some automatic car washes could damage the vehicle.
Vehicle Care Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Notice: Driving the vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, could damage the aluminum or chrome-plated wheels.
10-90 Vehicle Care Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect.
Vehicle Care 10-91 Do not clean the interior using the following cleaners or techniques: . Do not heavily saturate the upholstery while cleaning. To clean: Never use a knife or any other sharp object to remove a soil from any interior surface. . Damage to the vehicle's interior may result from the use of many organic solvents such as naptha, alcohol, etc. 2. Remove excess moisture. . . . . Never use a stiff brush. It can cause damage to the vehicle's interior surfaces.
10-92 Vehicle Care A paper towel can be used to blot excess moisture from the fabric or carpet after the cleaning process. Leather To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat, steam, or spot lifters or spot removers, or shoe polish on leather.
Vehicle Care Floor Mats If the floor mat has a snap retainer, a grommet in the driver side floor mat attaches to a hook on the floor of the vehicle to secure the floor mat. To remove the floor mat, pull the mat towards the rear of the vehicle until the grommet can be removed from the hook. If the floor mat has a knob retainer, a grommet in the floor mat attaches to a knob on the floor of the vehicle to secure the floor mat.
10-94 Vehicle Care 2 NOTES
Service and Maintenance Service and Maintenance General Information General Information . . . . . . . . . . 11-1 Scheduled Maintenance Scheduled Maintenance . . . . . 11-2 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . 11-7 Maintenance Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 11-8 Maintenance Records Maintenance Records . . . . . . . .
11-2 Service and Maintenance { WARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury. Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer/ retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 10‑4. At your General Motors dealer/ retailer, you can be certain that you will receive the highest level of service available.
Service and Maintenance system whenever the oil is changed. See Engine Oil Life System on page 10‑10. . When the Change Engine Oil Soon message displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: . . . Tire wear inspection. See Tire Inspection on page 10‑49. . Rotate tires. See Tire Rotation on page 10‑49. .
11-4 . . . Service and Maintenance Body hinges and latches, key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats, and liftgate hinges lubrication. See Recommended Fluids and Lubricants on page 11‑7. More frequent lubrication may be required when vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer, seal better, and not stick or squeak.
Service and Maintenance maintenance, if a power washer is used to clean mud and dirt from the underbody, care should be taken to not directly spray the transfer case output seals. High pressure water can overcome the seals and contaminate the transfer case fluid. Contaminated fluid will decrease the life of the transfer case and should be replaced. First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks.
11-6 Service and Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • Tire inflation pressures check. • • Tire wear inspection. • • Rotate tires. • • Fluids visual leak check. • • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). • • Brake system inspection. • • Steering and suspension inspection.
Service and Maintenance 11-7 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Engine Oil Engine Coolant Hydraulic Brake System Windshield Washer Hydraulic Power Steering System Automatic Transmission Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for the vehicle's engine, see Engine Oil on page 10‑8.
11-8 Service and Maintenance Usage Fluid/Lubricant Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and Release Pawl Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Hood and Door Hinges and Rear Folding Seat Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Weatherstrip Conditioning Weatherstrip Lubricant (GM Part No. U.S.
Service and Maintenance 11-9 Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts.
11-10 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 11-11
11-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Technical Data Technical Data Vehicle Identification Vehicle Identification Vehicle Identification Number (VIN) Vehicle Identification Number (VIN) . . . . . . . . . . . . . . 12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . 12-1 Vehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . . 12-3 This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle.
12-2 Technical Data Vehicle Data Capacities and Specifications The following approximate capacities are given in metric and English conversions. See Recommended Fluids and Lubricants on page 11‑7 for more information. Capacities Application Air Conditioning Refrigerant R134a Metric English For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information. Cooling System 10.8 L 11.
Technical Data Engine Specifications Engine 3.6L V6 Engine Engine Drive Belt Routing 3.6L V6 Engine VIN Code Transmission Spark Plug Gap D Automatic 1.10 mm (0.
12-4 Technical Data 2 NOTES
Customer Information Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 13-1 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . . . 13-4 Customer Assistance for Text Telephone (TTY) Users . . . . . 13-4 Online Owner Center . . . . . . . . 13-5 GM Mobility Reimbursement Program . . . . . . . . . . . . . . . . . . . . 13-5 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . . 13-5 Scheduling Service Appointments . . . . .
13-2 Customer Information STEP TWO : Should you need additional assistance, in the U.S., contact the Saturn Customer Assistance Center by calling 1-800-553-6000. In Canada, call the Saturn Customer Communication Centre at 1-800-263-1999. A Saturn Customer Assistance Center team member will handle your call and assist in providing product and warranty information, the nearest retailer location, roadside assistance, brochures, literature and discuss any concerns you may have.
Customer Information Contact the BBB Auto Line Program by using the toll-free telephone number or by writing them at the following address: BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800 Arlington, VA 22203-1838 Telephone: 1-800-955-5100 dr.bbb.org/goauto This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage and other factors.
13-4 Customer Information Customer Assistance Offices Saturn encourages customers to call the toll-free number for assistance. If a customer wishes to write to Saturn, the letter should be addressed to: Saturn Customer Assistance Center P.O. Box 33173 Detroit, MI 48232-5173 1-800-553-6000 1-800-833-6000 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-553-6000 In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd.
Customer Information Online Owner Center Other Helpful Links: Online Owner Center (U.S.) — www.gmownercenter.com/ saturn Saturn Merchandise — www.saturncollection.com Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records . Find Saturn retailers for service nationwide . Exclusive privileges and offers . Recall notices for your specific vehicle .
13-6 Customer Information Calling for Assistance When calling Roadside Assistance, have the following information ready: . Your name, home address, and home telephone number . Telephone number of your location . Location of the vehicle . Model, year, color, and license plate number of the vehicle . Odometer reading, Vehicle Identification Number (VIN), and delivery date of the vehicle . Description of the problem Roadside Assistance is not a part of the New Vehicle Limited Warranty.
Customer Information . Mounting, dismounting or changing of snow tires, chains, or other traction devices. . Towing or services for vehicles driven on a non-public road or highway. . Services Specific to Canadian Purchased Vehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. . Lock-Out Service: Vehicle registration is required. .
13-8 Customer Information Courtesy Transportation Program To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid specific warranty in both the U.S. and Canada. Several courtesy transportation options are available to assist in reducing your inconvenience when warranty repairs are required.
Customer Information Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc. You are responsible for fuel usage charges and may also be responsible for taxes, levies, usage fees, excessive mileage, or rental usage beyond the completion of the repair. It may not be possible to provide a like-vehicle as a courtesy rental. Additional Program Information All program options, such as shuttle service, may not be available at every dealer.
13-10 Customer Information durability/corrosion problems, and may not perform properly in subsequent collisions. Aftermarket parts are not covered by your GM New Vehicle Limited Warranty, and any vehicle failure related to such parts are not covered by that warranty. Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs.
Customer Information . Vehicle Identification Number (VIN) . Insurance company and policy number . General description of the damage to the other vehicle Choose a reputable repair facility that uses quality replacement parts. See “Collision Parts” earlier in this section. If the airbag has inflated, see What Will You See After an Airbag Inflates? on page 3‑35.
13-12 Customer Information Owner Publications Service Bulletins Information on how to obtain product bulletins and as described below is applicable only in the fifty U.S. states and the District of Columbia, and only for cars and light trucks with a Gross Vehicle Weight Rating (GVWR) less than 10,000 pounds (4 536 kg). Copies of individual bulletins are also at your participating Saturn retailer. You can ask to see them.
Customer Information Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying General Motors.
13-14 Customer Information Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify Saturn. Call 1-800-553-6000, or write: Saturn Customer Assistance Center P. O.
Customer Information This data can help provide a better understanding of the circumstances in which crashes and injuries occur. Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) is recorded.
13-16 Customer Information Radio Frequency Identification (RFID) Radio Frequency Statement RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security, as well as in connection with conveniences such as key fobs for remote door locking/ unlocking and starting, and in-vehicle transmitters for garage door openers.
INDEX A Accessories and Modifications . . . . . . . . . . . . . . . . . 10-3 Accessory Power . . . . . . . . . . . . . . 9-17 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . 9-54 Adding Equipment to the Airbag-Equipped Vehicle . . . . . 3-42 Adjustments Lumbar, Front Seats . . . . . . . . . . . 3-5 Air Cleaner/Filter, Engine . . . . . 10-12 Air Vents . . . . . . . . . . . . . . . . . . . . . . 8-12 Airbag System Check . . . . . . . . . . . . . . . . . . . . . . . .
i-2 INDEX Brakes . . . . . . . . . . . . . . . . . . . . . . . . 10-22 Antilock . . . . . . . . . . . . . . . . . . . . . . .9-26 Assist . . . . . . . . . . . . . . . . . . . . . . . . .9-27 Fluid . . . . . . . . . . . . . . . . . . . . . . . . 10-23 Parking . . . . . . . . . . . . . . . . . . . . . . .9-27 System Messages . . . . . . . . . . . .5-34 Braking . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Break-In, New Vehicle . . . . . . . . . 9-15 Bulb Replacement . . . . . . . . . . . .
INDEX Compressor Kit, Tire Sealant . . . . . . . . . . . . . . . . . . . . . . 10-59 Control of a Vehicle . . . . . . . . . . . . . 9-3 Convenience Net . . . . . . . . . . . . . . . 4-3 Convex Mirrors . . . . . . . . . . . . . . . . 2-16 Coolant Engine . . . . . . . . . . . . . . . . . . . . . . 10-14 Engine Temperature Gage . . . .5-14 Engine Temperature Warning Light . . . . . . . . . . . . . . .5-22 Cooling System . . . . . . . . . . . . . . . 10-14 Engine Messages . . . . . . . . . . . .
i-4 INDEX E Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . . 9-54 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-31 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . 10-31 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . . 10-34 Overload . . . . . . . . . . . . . . . . . . . 10-30 Engine Air Cleaner/Filter . . . . . . . . . . . 10-12 Check and Service Engine Soon Lamp . . . . . . . . . . . . . . . . . .
INDEX Fuses Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-31 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . 10-31 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . . 10-34 General Information Service and Maintenance . . . . . 11-1 Towing . . . . . . . . . . . . . . . . . . . . . . . .9-43 Vehicle Care . . . . . . . . . . . . . . . . . .10-2 Glove Box . . . . . . . . . . . . . . . . . . . . . . 4-1 GM Mobility Reimbursement Program . . . . . . . . . . .
i-6 INDEX J Jump Starting . . . . . . . . . . . . . . . . . 10-78 K Key and Lock Messages . . . . . . . 5-37 Keyless Entry Remote (RKE) System . . . . . . . . 2-3 Keyless Entry System . . . . . . . . . . 2-2 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 L Labeling, Tire Sidewall . . . . . . . . 10-37 Lamp Messages . . . . . . . . . . . . . . . 5-37 Lamps Courtesy . . . . . . . . . . . . . . . . . . . . . . . 6-5 Dome . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX M Maintenance Records . . . . . . . . . . . . . . . . . . . . . . 11-9 Maintenance Schedule Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . . 11-7 Scheduled Maintenance . . . . . . 11-2 Malfunction Indicator Lamp . . . . 5-17 Manual Mode . . . . . . . . . . . . . . . . . . 9-24 Messages Airbag System . . . . . . . . . . . . . . . .5-38 Anti-Theft Alarm System . . . . . .5-38 Battery Voltage and Charging . . . . . . . . . . . . . . . . . . . .5-33 Brake System . . . . . . . . . .
i-8 INDEX Outlets Power . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Overheated Engine Protection Operating Mode . . . . . . . . . . . . . 10-20 Overheating, Engine . . . . . . . . . . 10-18 P Parade Dimming . . . . . . . . . . . . . . . . 6-7 Park Shifting Into . . . . . . . . . . . . . . . . . . .9-19 Shifting Out of . . . . . . . . . . . . . . . .9-20 Park Tilt Mirrors . . . . . . . . . . . . . . . . 2-18 Parking Assist, Ultrasonic . . . . . . . . . . . . .9-32 Brake . . . . . . . . . . . . .
INDEX Reclining Seatbacks . . . . . . . . . . . . 3-6 Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . . . 11-7 Recommended Fuel . . . . . . . . . . . 9-39 Records Maintenance . . . . . . . . . . . . . . . . . . 11-9 Recreational Vehicle Towing . . . . . . . . . . . . . . . . . . . . . . 10-83 Reimbursement Program, GM Mobility . . . . . . . . . . . . . . . . . . 13-5 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . 2-2, 2-3 Remote Vehicle Start . . . . . . . . . . .
i-10 INDEX Security Light . . . . . . . . . . . . . . . . . . . . . . . . . .5-23 Vehicle . . . . . . . . . . . . . . . . . . . . . . .2-13 Service Accessories and Modifications . . . . . . . . . . . . . . . .10-3 Doing Your Own Work . . . . . . . .10-4 Engine Soon Lamp . . . . . . . . . . .5-17 Maintenance Records . . . . . . . . 11-9 Maintenance, General Information . . . . . . . . . . . . . . . . . . 11-1 Parts Identification Label . . . . .12-1 Publications Ordering Information . . . . . . . . . . . .
INDEX Tires (cont.) If a Tire Goes Flat . . . . . . . . . . 10-57 Inflation Monitor System . . . . 10-46 Inspection . . . . . . . . . . . . . . . . . . 10-49 Messages . . . . . . . . . . . . . . . . . . . .5-39 Pressure Light . . . . . . . . . . . . . . . .5-22 Pressure Monitor System . . . 10-44 Rotation . . . . . . . . . . . . . . . . . . . . 10-49 Sealant and Compressor Kit . . . . . . . . . . . 10-59 Sealant and Compressor Kit, Storing . . . . . . . . . . . . . . . . 10-66 Secondary Latch System . . .
i-12 INDEX Vehicle Identification Number (VIN) . . . . . . . . . . . . . . . . .12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . .12-1 Vehicle Reminder Messages . . . . . . . . . . . . . . . . . . . . 5-41 Ventilation, Air . . . . . . . . . . . . . . . . . 8-12 Visors . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 Voltage Devices, and Wiring . . . . . . . . . . . . . . . . . . . . . . . 10-30 Voltmeter Gage . . . . . . . . . . . . . . . .
