sauder.com Great for all those books you’ll never read. 5-Shelf Bookcase Model 410175 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 533263 10/02/19 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Français 19-21 Español 22-24 Safety 25-26 Warranty Hammer Not actual size Nail Holder (provided) 27 Skip the power trip. This time. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification E M A H J K N J B K C G N I P O N J D P www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F Page 4 HIDDEN CAM - 12 2F 1G CAM DOWEL - 12 SAFETY BRACKET - 1 5G ANGLE BRACKET - 8 13P CAM COVER - 8 14P HOLE PLUG - 3 1R METAL PIN - 12 2S BLACK 1-7/8" FLAT HEAD SCREW - 5 9S BLACK 1-1/8" PAN HEAD SCREW - 3 1S BLACK 9/16" LARGE HEAD SCREW - 17 1N NAIL - 55 410175 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B), LOWER ENDS (C and D), and BOTTOM (F). Then, insert the metal end of a CAM DOWEL (2F) into the HIDDEN CAMS. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Fasten the ENDS (A and B) to the TOP (E). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Long finished edge E Notched edge with e c fa Sur S AM C DEN HID Su witrface hh ole s B Notched edge out h t i ew fac r u S MS CA N DE HID A Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 3 å Fasten the TOP MOLDING (M) to the TOP (E). Use three BLACK 1-1/8" PAN HEAD SCREWS (9S). å å NOTE: Do not overtighten the SCREWS into the TOP. Insert three HOLE PLUGS (14P) into the holes in the TOP MOLDING (M). 9S Curved edge BLACK 1-1/8" PAN HEAD SCREW (3 used in this step) 14P M E www.sauder.
Step 4 å Slide the END MOLDINGS (K) onto the notched edges of the ENDS (A and B). å * U.S. Patent No. 5,499,886 Notched edge Notched edge Slide the END MOLDINGS (K) onto the notched edges. B K A K Large groove Large groove Page 8 410175 www.sauder.
Step 5 å Fasten the SHELF (G) to the ENDS (A and B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Long finished edge B These holes must be here. A G Su morface re wi ho th les 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 6 å Fasten the LOWER LEFT END (D) to the SHELF (G). Tighten two HIDDEN CAMS. Notched edge e fac r u S withDEN HID S M CA G D Maximum 210 degrees Arrow Minimum 190 degrees Page 10 410175 www.sauder.
Step 7 å Fasten the BOTTOM (F) to the LOWER LEFT END (D). Tighten two HIDDEN CAMS. Notched edge These holes must be here. D G F Su HI rface DD w EN ith CA MS Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 8 å Fasten the LOWER RIGHT END (C) to the BOTTOM (F) and SHELF (G). Tighten four HIDDEN CAMS. å Slide the LOWER END MOLDINGS (P) onto the notched edges of the LOWER ENDS (C and D). å * U.S. Patent No. 5,499,886 Notched edge Slide the LOWER END MOLDINGS (P) onto the notched edges. D G P F P C ut itho S w e fac AM Sur DEN C HID Notched edge Large groove Maximum 210 degrees Minimum 190 degrees Large groove Page 12 Arrow 410175 www.sauder.
Step 9 å Fasten five ANGLE BRACKETS (5G) to the LOWER ENDS (C and D) and BOTTOM (F). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the ANGLE BRACKETS are even with the edges of the LOWER ENDS and BOTTOM. å Fasten the BASE (L) to the LOWER ENDS (C and D) and BOTTOM (F). Use five BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the LOWER ENDS and BOTTOM. Rounded edge L ed h is n Fi D e ac rf su F C 5G 5G 1S 5G www.sauder.
Step 10 å Fasten three ANGLE BRACKETS (5G) to the SHELF (G). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the SKIRT (O) to the SHELF (G). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: There are no pre-drilled holes in the SKIRT. The SCREWS will tighten into the groove. 5G O G 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) Page 14 410175 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the LARGE BACK (H) and lay it over your unit. å Make equal margins along all four edges of the LARGE BACK (H). Push on opposite corners of your unit if needed to make it "square". å Fasten the LARGE BACK (H) to three edges of your unit using the NAILS (1N). We have provided a Nail Holder tool to use in this step for proper positioning of the NAILS.
Step 12 å Slide the SHELF MOLDING (N) onto the notched edge of one of the ADJUSTABLE SHELF (J). å å Repeat this step for the other ADJUSTABLE SHELVES (J). * U.S. Patent No. 5,499,886 These surfaces should be even. J Notched edge N Slide the SHELF MOLDING (N) onto the notched edge. Page 16 410175 www.sauder.
Step 13 å å Carefully stand your unit upright. å Set the ADJUSTABLE SHELVES (J) onto the METAL PINS. Insert the METAL PINS (1R) into the hole locations of your choice in the ENDS (A and B) and LOWER ENDS (C and D). B J J A D J (12 used) 1R www.sauder.
Step 14 å å NOTE: This unit must be placed against a wall. å å å Push a CAM COVER (13P) onto each visible HIDDEN CAM. We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry.
Modèle 410175 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer la TABLETTE (G) aux EXTRÉMITÉS (A et B). Utiliser quatre VIS NOIRES TÊTE PLATE 48 mm (2S). Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Enfoncer douze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), les EXTRÉMITÉS INFÉRIEURES (C et D) et le DESSOUS (F).
ÉTAPE 10 ÉTAPE 13 Fixer trois CONSOLES À ÉQUERRE (5G) à la TABLETTE (G). Utiliser trois VIS NOIRES TÊTE LARGE 14 mm (1S). Relever, avec précaution, l’élément dans sa position verticale. Fixer la PLINTHE (O) à la TABLETTE (G). Utiliser trois VIS NOIRES TÊTE LARGE 14 mm (1S). Insérer les GOUPILLES EN MÉTAL (1R) dans les trous choisis dans les EXTRÉMITÉS (A et B) et EXTRÉMITÉS INFÉRIEURES (C et D). REMARQUE : La PLINTHE ne comporte pas de trous pré-percés. Serrer les VIS dans la rainure.
Modelo 410175 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el ESTANTE (G) a los EXTREMOS (A y B). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (2S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje doce EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), los EXTREMOS INFERIORES (C y D) y del FONDO (F).
PASO 10 PASO 13 Fije tres SOPORTES ANGULARES (5G) al ESTANTE (G). Utilice tres TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Cuidadosamente ponga la unidad en posición vertical. Fije el FALDÓN (O) al ESTANTE (G). Utilice tres TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Inserte las ESPIGAS DE METAL (1R) dentro de los agujeros al nivel preferido de los EXTREMOS (A y B) y los EXTREMOS INFERIORES (C y D). NOTA: No hay agujeros perforados en el FALDÓN. Los TORNILLOS apretarán dentro de la ranura.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
