sauder.com You could totally write a novel on this. Writing Table Beginnings Collection | Model 410421 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-14 Hammer Français 15-17 Español 18-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 410421 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Insert a CONNECTOR SCREW (8S) into each HIDDEN CONNECTOR (5F). Scan this QR code or go to this address: http://qr.sauder.com/?ID=1334 to watch a video on how to assemble your unit. 5F 8S Step 2 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Use your hammer to tap two HIDDEN CONNECTORS (5F) with SCREWS into one of the ENDS (A).
Step 3 å Insert eight METAL PINS (1R) into the ENDS (A) and STRETCHERS (G). å Insert the METAL PINS (1R) in the ENDS (A) and STRETCHERS (G) into the holes in the LEGS (H and I). å Now, fasten the LEGS (H and I) to the ENDS (A) and STRETCHERS (G). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) Surface with HIDDEN CONNECTOR These edges should be even. These edges should be even. H A Surface with HIDDEN CONNECTOR These edges should be even.
Step 4 å Fasten the BACK (E) and FRONTS (F) to the LEGS (H and I). Use eight BLACK 1-1/8" PAN HEAD SCREWS (9S). å Fasten the ENDS (A) to the BACK (E) and FRONTS (F). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). This surface should be the same finish as this surface. H This surface should be the same finish as this surface. F A F A I E I 9S BLACK 1-1/8" PAN HEAD SCREW (8 used for the LEGS) H 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used for the ENDS) www.sauder.
Step 5 å Fasten the ENDS (A) to the TOP (D). Tighten four HIDDEN CONNECTORS. Hey! It's starting to look like something! How to use the HIDDEN CONNECTOR To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR. While pushing the screw into the hole of the adjoining part, turn the screwdriver clockwise to tighten. A D ce urfa s d e nish Unfi A Long finished edge Page 8 410421 www.sauder.
Step 6 å Fasten the UPRIGHTS (B and C) to the TOP (D). Tighten four HIDDEN CONNECTORS. å Fasten the UPRIGHTS (B and C) to the BACK (E) and FRONTS (F). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Surface with HIDDEN CONNECTORS E C F D B F Finished edge Surface with HIDDEN CONNECTORS www.sauder.
Step 7 å Fasten the CABINET RIGHT (35DA) to the RIGHT UPRIGHT (B) and the CABINET LEFT (35DB) to the LEFT UPRIGHT (C). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) 3 3 B D 5 2 B C 3 2 1 1 Roller end D 35 Page 10 410421 A www.sauder.
Step 8 å Fasten the DRAWER BACK (D268) to the DRAWER SIDES (D266 and D267). Use two BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide the DRAWER BOTTOM (D622) into the grooves in the DRAWER SIDES (D266 and D267) and DRAWER BACK (D268). 30S BLACK 1-9/16" FLAT HEAD SCREW (2 used in this step) D268 D267 D266 Groove D267 D268 D622 ed sh ni Fi D266 ce rfa su www.sauder.
Step 9 å Fasten the DRAWER BOX FRONT (D269) to the DRAWER SIDES (D266 and D267). Use two BLACK 1-9/16" FLAT HEAD SCREWS (30S). å NOTE: Be sure the DRAWER BOTTOM (D622) inserts into the groove of the DRAWER BOX FRONT (D269). å Fasten the DRAWER FRONT (J) to the DRAWER BOX FRONT (D269). Use two BLACK 7/8" LARGE HEAD SCREWS (17S). 17S BLACK 7/8" LARGE HEAD SCREW (2 used for the DRAWER FRONT) D267 30S D622 D269 D266 J 30S BLACK 1-9/16" FLAT HEAD SCREW (2 used in this step) Page 12 410421 www.
Step 10 å å Fasten the DRAWER RIGHT (35DC) and DRAWER LEFT (35DD) to the DRAWER SIDES (D266 and D267). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Almost time to celebrate! With a nap. Fasten the PULL (104K) to the DRAWER FRONT (J). Use two BLACK 1-5/8" PAN HEAD SCREWS (27S) through the DRAWER BOX FRONT, through the DRAWER FRONT, and into the PULL.
Step 11 å å Carefully stand your unit upright. å å å Center a SCREW COVER (20P) over the head of each visible SCREW and press firmly. To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth.
Modèle 410421 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Insérer une VIS DE CONNECTEUR (8S) dans chaque CONNECTEUR ESCAMOTABLE (5F). Utilisation des CONNECTEURS ESCAMOTABLES Pour attacher deux pièces ensemble à l'aide des CONNECTEURS ESCAMOTABLES, il suffit d'insérer la pointe d'un tournevis en biseau dans la fente du CONNECTEUR ESCAMOTABLE. Tout en enfonçant la vis dans le trou dans la planche adjacente, tourner le tournevis, en biseau, dans le sens des aiguilles d'une montre pour serrer à bloc.
ÉTAPE 8 ÉTAPE 10 Fixer l'ARRIÈRE DE TIROIR (D268) à les CÔTÉS DE TIROIR (D266 et D267). Utiliser deux VIS TÊTE PLATE 40 mm NOIRE (30S). Fixer le TIROIR DROIT (35DC) et le TIROIR GAUCHE (35DD) aux CÔTÉS DE TIROIR (D266 et D267). Utiliser quatre VIS DORÉES TÊTE PLATE 8 mm (3S) à travers les trous nº 1 et nº 3. Enfiler le FOND DE TIROIR (D622) dans les rainures des CÔTÉS DE TIROIR ((D266 and D267) et de l'ARRIÈRE DE TIROIR (D268). ÉTAPE 9 Fixer la POIGNÉE (104K) au DEVANT DE TIROIR (J).
Modelo 410421 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 Inserte un TORNILLO CONECTOR (8S) dentro de cada CONECTOR INVISIBLE (5F). Cómo utilizar los CONECTORES INVISIBLES Para juntar dos partes usando los CONECTORES INVISIBLES, inserte su destornillador, en ángulo, dentro del encaje del CONECTOR INVISIBLE. Mientras empuje el tornillo dentro del agujero del tablero adjunto, gire el destornillador hacia la derecha para apretar. PASO 2 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 8 PASO 10 Fije DORSO DE CAJÓN (D268) a los LADOS DE CAJÓN (D266 y D267). Utilice dos TORNILLO NEGRO DE CABEZA PERDIDA de 40 mm (30S). Fije el CAJÓN DERECHO (35DC) y el CAJÓN IZQUIERDO (35DD) a los LADOS DE CAJÓN (D266 y D267). Utilice cuatro tornillos DORADOS de cabeza PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Deslice el FONDO DE CAJÓN (D622) dentro de las ranuras de los LADOS DE CAJÓN (D266 and D267) y del DORSO DE CAJÓN (D268).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
