sauder.com Store behind closed doors. Wardrobe/Storage Cabinet HomePlus Collection | 411312 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 364095 09/09/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification E C P I B H A F H D51 D175 K D2 D983 D50 L J O2 K VV VV WW WW www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 84S BLACK 3" PAN HEAD SCREW - 2 OO BLACK 1-7/8" FLAT HEAD SCREW - 5 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 PP BLACK 7/8" MACHINE SCREW - 6 QQ BLACK 9/16" LARGE HEAD SCREW - 7 RR BLACK 9/16" WAFER HEAD SCREW - 4 SS BLACK 1/2" FLAT HEAD SCREW - 12 UU NAIL - 52 3S GOLD 5/16" FLAT HEAD SCREW - 8 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (U) into the large holes in the TOP (C) and SHELF (F). Do not tighten the TWIST-LOCK® FASTENERS in this step. U F C U U Page 6 411312 www.sauder.
Step 2 å å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). Remember: Righty tighty. Lefty loosey. Fasten the ROD HANGERS (W) to the ENDS (A and B). Use two BLACK 9/16" LARGE HEAD SCREWS (QQ). QQ BLACK 9/16" LARGE HEAD SCREW (2 used for the ROD HANGERS) W Long finished edge A Roller end B Long finished edge Roller end 3S GOLD 5/16" FLAT HEAD SCREW (4 used for the CABINET RAILS) www.sauder.
Step 3 å Fasten the LEFT END (B) to the TOP (C) and SHELF (F). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 4 å Fasten the RIGHT END (A) to the TOP (C) and SHELF (F). Tighten four TWIST-LOCK® FASTENERS. å Fasten the TOP MOLDING (P) to the TOP (C). Tighten two TWIST-LOCK® FASTENERS. Curved edge P C Long finished edge A F www.sauder.
Step 5 å å Push the DOOR STOP (BB) into the hole in the TOP (C). Fasten the BOTTOM (D2) to the ENDS (A and B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (OO). BB C B Rounded edge A Un fin ish ed su rfa ce D2 OO BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Page 10 411312 www.sauder.
Step 6 å Use a hammer to drive a PROPEL NUT (DD) into the holes in the FEET (EE and FF). Now, turn an ADJUSTABLE GLIDE (CC) into each PROPEL NUT as shown in the upper diagram. å å Slide the FEET (EE and FF) into the notches in the SKIRTS (J and K). å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise. Fasten the SKIRTS (J and K) to the BOTTOM (D2).
Step 7 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (E) to your unit using the NAILS (UU). å NOTE: A perforation has been provided for access through the BACK. Carefully cut out the hole if needed. å Fasten the BALLASTS (VV and WW) to the BOTTOM (D2). Use two BLACK 3" PAN HEAD SCREWS (84S).
Step 8 å Fasten three HINGES (Z) to each DOOR (H). Use twelve BLACK 1/2" FLAT HEAD SCREWS (SS). SS BLACK 1/2" FLAT HEAD SCREW (12 used in this step) Z H H Z www.sauder.
Step 9 å å Carefully stand your unit upright. å Fasten a DOOR (H) to the LEFT END (B). Use the screws in the HINGES. See the next step for adjustments. å Fasten a LARGE PULL (GG) to the DOOR (H). Use two BLACK 7/8" MACHINE SCREWS (PP). å Repeat this step for the other door. Pro Tip: Lift with your legs. And, you know, your arms. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram.
Step 10 å å Refer to the enlarged diagram to identify the parts on the HINGES. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 11 å å Turn a CAM SCREW (8F) into the DRAWER FRONT (L). Push a HIDDEN CAM (1F) into the DRAWER BRACE (O2). 8F L Do not tighten the HIDDEN CAM in this step. O2 Arrow 1F Page 16 411312 www.sauder.
Step 12 VIEW THE T-SLOT BOX VIDEO å Pull the DRAWER FRONT BRACKETS (II) apart and slide them into the grooves in the DRAWER SIDES (D50 and D51). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å Fasten the DRAWER FRONT (L) to the DRAWER FRONT BRACKETS (II). Use four BLACK 9/16" LARGE HEAD SCREWS (QQ). å Slide the DRAWER BOTTOM (D983) into the grooves in the DRAWER SIDES (D50 and D51) and DRAWER FRONT (L).
Step 13 VIEW THE T-SLOT BOX VIDEO å Fasten the DRAWER BRACE (O2) to the DRAWER FRONT (L). Tighten one HIDDEN CAM. å Fasten the DRAWER BACK (D175 ) to the DRAWER SIDES (D50 and D51) and DRAWER BRACE (O2). Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S). 1 O2 1st 2 Surface with HIDDEN CAM L Start each screw a few turns before completely tightening any of them. 30S nd 2 BLACK 1-9/16" FLAT HEAD SCREW (5 used in this step) D175 D50 O2 D51 Page 18 411312 www.sauder.
Step 14 å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D50 and D51). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. å Fasten the PULL (HH) to the DRAWER FRONT (L). Use two BLACK 7/8" MACHINE SCREWS (PP). Roller end PP BLACK 7/8" MACHINE SCREW (2 used for the PULL) 1 2 4 3 D51 Roller end HH L D50 1 2 4 3 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 15 å å Place your unit into its final position against a wall. å Set the ROD (V) onto the ROD HANGERS on the ENDS (A and B). Push the RUBBER SLEEVES (MM) over the METAL PINS (LL). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELF (I) onto the METAL PINS. V B A I LL MM (4 used) Page 20 411312 www.sauder.
Step 16 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å To make adjustments to the drawer, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å Apply the WARNING LABEL (NN) to the left DOOR (H). You should be able to read the label when the DOOR is open. When the DOOR is closed, it will hide the label.
Step 17 å Fasten the SAFETY BRACKET (AA) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (QQ) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (OO) into a stud in your wall. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
411312 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 REMARQUE : Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage. Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (U) dans les gros trous du DESSUS (C) et de la TABLETTE (F).
ÉTAPE 11 ÉTAPE 15 Ne pas serrer l'EXCENTRIQUE ESCAMOTABLE dans cette étape. Placer l’unité à sa place finale, contre un mur. Faire tourner une VIS D'EXCENTRIQUE (8F) dans le DEVANT DE TIROIR (L). Enfoncer les MANCHONS EN CAOUTCHOUC (MM) sur les GOUPILLES EN MÉTAL (LL). Insérer les GOUPILLES EN MÉTAL dans les trous choisis dans les EXTRÉMITÉS (A et B). Poser la TABLETTE RÉGLABLE (I) sur les GOUPILLES EN MÉTAL. Enfoncer une EXCENTRIQUE ESCAMOTABLE (1F) dans l’ENTRETOISE DE TIROIR (O).
411312 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 NOTA: No apriete los SUJETADORES TWIST-LOCK® por ahora. Precaución No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (U) dentro de los agujeros grandes del PANEL SUPERIOR (C) y del ESTANTE (F).
PASO 11 PASO 15 No apriete el EXCÉNTRICO ESCONDIDO en este paso. Coloque su unidad en su posición final contra una pared. Inserte un BIELA DE EXCÉNTRICO (8F) en la CARA DE CAJÓN (L). Empuje un EXCÉNTRICO ESCONDIDO (1F) dentro de la RIOSTRA DE CAJÓN (O). Empuje los MANGUITOS DE GOMA (MM) sobre las ESPIGAS DE METAL (LL). Inserte las ESPIGAS DE METAL dentro de los agujeros al nivel preferido de los EXTREMOS (A y B). Coloque el ESTANTE AJUSTABLE (I) sobre las ESPIGAS DE METAL.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.