sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Dresser Palladia Collection | Model 411830 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 Assembly Steps 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification M D F A2 R N C2 R2 B2 S E H R2 D245 D60 D262 D171 D979 D979 D271 M64 O2 D257 M64 I2 T www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S BLACK 9/16" LARGE HEAD SCREW - 45 2S BLACK 1-7/8" FLAT HEAD SCREW - 2 3S GOLD 5/16" FLAT HEAD SCREW - 48 7S BLACK 1-1/4" FLAT HEAD SCREW - 9 12S BROWN 1" FLAT HEAD SCREW - 6 30S BLACK 1-9/16" FLAT HEAD SCREW - 30 38S SILVER 1/2" MACHINE SCREW - 8 50S GOLD 1" MACHINE SCREW - 4 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A2 and B2). Repeat this step for the UPRIGHT (C2) and BOTTOM (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F (12 used) 10F A2 B2 10F Page 6 411830 www.sauder.
Step 2 å Push four HIDDEN CAMS (1F) into the BOTTOM (E). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 1F 2F (4 used) E Arrow Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.
Step 3 å Tap two MOLDING CONNECTORS (17F) into the notches in the MOLDINGS (M, N, and R). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS. Flat end Flat end 17F 17F N R Page 8 411830 M www.sauder.
Step 4 å å Fasten the MOLDINGS (M, N, and R) to the TOP (D). Use nine BLACK 1-1/4" FLAT HEAD SCREWS (7S). Remember: Righty tighty. Lefty loosey. NOTE: Do not overtighten the SCREWS into the TOP. 7S Finished surface BLACK 1-1/4" FLAT HEAD SCREW (9 used in this step) N R ed h is fin n U e ac rf su D M Long flat edge www.sauder.
Step 5 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A2 and B2) and both surfaces of the UPRIGHT (C2). Use twenty-four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
Step 6 å Fasten the LEFT END (B2) to the LEFT MOLDING (N) on the TOP (D). Tighten two TWIST-LOCK® FASTENERS. å Fasten the UPRIGHT (C2) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 7 å Fasten the BOTTOM (E) to the LEFT END (B2). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (E) to the UPRIGHT (C2). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the RIGHT END (A2) to the BOTTOM (E) and RIGHT MOLDING (M). Tighten four TWIST-LOCK® FASTENERS. Edge with HIDDEN CAMS Edge with TWIST-LOCK® FASTENER B2 Sur f TW ace wi IS th FAS T-LO TEN CK® ERS C2 E A2 M 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 12 411830 www.sauder.
Step 8 å Fasten two METAL BRACKETS (4G) to the BOTTOM (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edge of the BOTTOM. å Fasten the BOTTOM MOLDING (S) to the BOTTOM (E). Tighten four HIDDEN CAMS. å Fasten the PLINTHS (R2) to the ENDS (A2 and B2) and BOTTOM (E). Tighten two TWIST-LOCK® FASTENERS and use two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 9 å Fasten six METAL BRACKETS (4G) to the BASE (H). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edge of the BASE. å Fasten the BASE (H) to the BOTTOM (E). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BOTTOM. 4G H 1S BLACK 9/16" LARGE HEAD SCREW (12 used in this step) H E Page 14 411830 www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along three edges of the BACK (F). The BACK will overhang the BOTTOM (E) slightly. Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å å Push the FOOT (3E) into the hole in the BOTTOM (E).
Step 11 å å Turn six CAM SCREWS (8F) into the DRAWER FRONTS (I2 and O2). Push six HIDDEN CAMS (1F) into the DRAWER BRACES (M64). 8F (6 used) I2 I2 I2 I2 O2 O2 Do not tighten the HIDDEN CAMS in this step. M64 M64 M64 M64 Arrow M64 M64 Arrow 1F Page 16 (6 used) 411830 Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 12 å Fasten the DRAWER FRONT MOLDINGS (T) to the DRAWER FRONTS (O2). Use six BROWN 1" FLAT HEAD SCREWS (12S). Don't worry. It isn't Rome. This can be built in a day. 12S BROWN 1" FLAT HEAD SCREW (6 used in this step) Rounded edge ce fa ur S t ou ith w ve oo gr O2 Finished surface T Rounded edge ce fa ur S t ou ith w ve oo gr O2 Finished surface T www.sauder.
Step 13 VIEW THE T-SLOT BOX VIDEO Push down 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 8G O2 D271 D979 Un fin ish ed D245 su rfa ce Groove D245 1S D271 O2 BLACK 9/16" LARGE HEAD SCREW (24 used in this step) å Pull the DRAWER FRONT BRACKETS (8G) apart and slide them into the grooves in the DRAWER SIDES (D245 and D271). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
Step 14 VIEW THE DRAWER GLIDE VIDEO å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D245) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D271). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å å NOTE: The glides are not intended to rotate. Fasten two KNOBS (33K) to the DRAWER FRONT (O2). Use two GOLD 1" MACHINE SCREWS (50S). Repeat this step for the other drawers. Use the SILVER 1/2" MACHINE SCREWS (38S) for the KNOBS on the large drawers.
Step 15 å Carefully stand your unit upright and position your unit in its final location. We recommend using the SAFETY STRAP (60M) for added stability. å NOTE: Do not turn the SAFETY DRYWALL ANCHOR (61M) into a wall stud. If you prefer to fasten the SAFETY STRAP (60M) to a wall stud, go to your local hardware store for proper hardware. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1.
Step 16 å To insert the drawers into your unit, tip the fronts of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the fronts of the drawers up and slide them into the unit. å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. O2 I2 O2 I2 I2 Place the glide on the SLIDE behind the glide on the RAIL. I2 www.sauder.
Step 17 å Apply the WARNING LABEL (5L) to the DRAWER SIDE (D271). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram. å å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
Modèle 411830 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage. Fixer le DESSOUS (E) à l'EXTRÉMITÉ GAUCHE (B2). Serrer deux FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A2 et B2). Répéter cette étape pour le MONTANT (C2) et le DESSOUS (E). Fixer le DESSOUS (E) au MONTANT (C2).
ÉTAPE 10 (SUITE) ÉTAPE 15 REMARQUE : Des lignes perforées ont été prévues pour accéder facilement à l'ARRIÈRE. Découper avec précaution les trous nécessaires. Relever, avec précaution, l'élément dans sa position verticale et placer l'élément dans son emplacement final. Il est recommandé d’utiliser la SANGLE DE SÉCURITÉ (60M) pour stabilité additionnelle. Insérer le PIED (3E) dans le trou dans le DESSOUS (E). Fixer les PLAQUES DE LIAISON (3G) au SOCLE (H) et aux PLINTHES (R2).
Modelo 411830 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® por ahora. Fije el FONDO (E) al EXTREMO IZQUIERDO (B2). Apriete dos SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A2 y B2). Repita este paso para el PARAL (C2) y el FONDO (E). Fije el FONDO (E) al PARAL (C2).
PASO 10 (CONTINUACIÓN) PASO 15 Fije las PLACAS DE CONEXIÓN (3G) a la BASE (H) y a las BASES (R2). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Cuidadosamente ponga la unidad en posición vertical y coloque su unidad en su posición final. Se recomienda utilizar la CORREA DE SEGURIDAD (60M) para mayor estabilidad. PASO 11 NOTA: No gire el ANCLAJE DE SEGURIDAD PARA EL DRYWALL (61M) en un montante de la pared.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from the bottom to the top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones y estantes sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
