sauder.com How else are you gonna know which end is up? Twin Headboard Shoal Creek Collection | Model 412091 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-20 Hammer Français 21-23 Español 24-26 Warranty Page 2 Not actual size Electric dril with 1/4" bit (Use only in indicated step) 27 412091 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) E TOP (1) I BACK (1) B LEFT END (1) F PANEL (1) J FLIP-UP DOOR (1) C RIGHT UPRIGHT (1) G SHELF (1) K ADJUSTABLE SHELF (2) D LEFT UPRIGHT (1) H SMALL SHELF (1) E I D C K H K B J G A F www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. L M2 HIDDEN CAM - 14 TWIST-LOCK® FASTENER - 4 P O ANGLE BRACKET - 3 R S DOOR STOP - 1 Page 4 N2 CAM DOWEL - 14 NUT - 4 RUBBER SLEEVE - 8 U HINGE SPACER - 2 V HINGE - 2 W KNOB - 1 X 412091 Q WASHER - 4 T METAL PIN - 12 HEADBOARD BRACKET - 2 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 117S SILVER 1-1/4" BOLT - 4 AA SILVER 5/8" FLAT HEAD SCREW - 4 Z BLACK 1-1/8" MACHINE SCREW - 1 BB BLACK 9/16" LARGE HEAD SCREW - 14 CC NAIL - 30 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (L) into the large holes in the UPRIGHTS (C and D). Do not tighten the TWIST-LOCK® FASTENERS in this step. L D C Page 6 412091 www.sauder.
Step 2 å Push fourteen HIDDEN CAMS (M2) into the ENDS (A and B), UPRIGHTS (C and D), PANEL (F), and SHELF (G). Then, insert the metal end of a CAM DOWEL (N2) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow N2 (14 used) M2 G F B A Arrow D C Arrow M2 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. N2 www.sauder.
Step 3 å Fasten the LEFT END (B) and LEFT UPRIGHT (D) to the TOP (E). Tighten three HIDDEN CAMS. Some assembly (and snacks) required. Angled edge Finished edge withM e c fa A Sur DEN C D HID B withMS e c fa A Sur DEN C HID Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 4 å å Insert four METAL PINS (T) into the SMALL SHELF (H). Insert the METAL PINS (T) in one end of the SMALL SHELF (H) into the holes in the LEFT UPRIGHT (D). Finished edge D H T www.sauder.
Step 5 å Fasten the RIGHT UPRIGHT (C) to the TOP (E) and SMALL SHELF (H). Tighten the HIDDEN CAM. å NOTE: Be sure the PINS in the SMALL SHELF (H) insert into the holes in the RIGHT UPRIGHT (C). å With a hammer, tap the DOOR STOP (R) into the small hole in the SHELF (G) as shown in the lower diagram. Maximum 210 degrees Arrow Minimum 190 degrees Angled edge H C E G t ou th S wi AM ce C rfa EN Su IDD H R Page 10 412091 www.sauder.
Step 6 å Fasten two HINGE SPACERS (U) and two HINGES (V) to the FLIP-UP DOOR (J). Use four SILVER 5/8" FLAT HEAD SCREWS (AA). AA SILVER 5/8" FLAT HEAD SCREW (4 used in this step) V U V J U www.sauder.
Step 7 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the FLIP-UP DOOR (J) to the SMALL SHELF (H). Use the screws in the HINGE. See step 9 for adjustments. å NOTE: The top edge of the DOOR (J) and the top surface of the SMALL SHELF (H) should be even. å Fasten the KNOB (W) to the FLIP-UP DOOR (J).
Step 8 å å å Fasten the SHELF (G) to the UPRIGHTS (C and D). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: Be sure the CAM DOWELS in the SHELF insert into the holes in the LEFT END (B). NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Fasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS. 2.
Step 9 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOOR may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOOR up or down (vertical) turn the adjusting screw in or out. å To adjust the DOOR side to side (horizontal), loosen all horizontal adjustment screws. Move the DOORS side to side to the desired location. Tighten the screws after making adjustments.
Step 10 å å Fasten three ANGLE BRACKETS (O) to the PANEL (F). Use three BLACK 9/16" LARGE HEAD SCREWS (BB). Now might be a good time to refresh your drink. NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the PANEL. ce rfa Su th wi EN DD HI S M CA F O BB BLACK 9/16" LARGE HEAD SCREW (3 used in this step) www.sauder.
Step 11 å å Carefully stand your unit on its TOP (E). å Fasten the PANEL (F) to the SHELF (G). Use three BLACK 9/16" LARGE HEAD SCREWS (BB) through the ANGLE BRACKETS and into the SHELF. Maximum 210 degrees Fasten the PANEL (F) to the LEFT END (B). Tighten two HIDDEN CAMS. Arrow Minimum 190 degrees BB B BLACK 9/16" LARGE HEAD SCREW (3 used in this step) Sur HIDface w DEN ith CA MS F G E Page 16 412091 www.sauder.
Step 12 å Fasten the RIGHT END (A) to the TOP (E), PANEL (F), and SHELF (G). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees ut itho S w e fac AM Sur DEN C HID F A G E Angled edge www.sauder.
Step 13 å Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (CC). å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (C and D) and SMALL SHELF (H).
Step 14 å å Carefully stand your unit upright. å Fasten the HEADBOARD BRACKETS (X) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (BB). Use the holes that are best suited for the height of your bedframe. å NOTE: If you purchased the Mates Bed #412093 go to the next step on how to fasten it to this unit. å Fasten the bedframe to the HEADBOARD BRACKETS (X). Use four SILVER 1-1/4" BOLTS (117S), WASHERS (Q), and NUTS (P).
Step 15 å Finish drilling out four 1/4" holes in the END of the #412093 Mates Bed that will get fastened to the Twin Headboard. Fasten the Mates Bed to the Twin Headboard with four SILVER 1-1/4" BOLTS (117S), WASHERS (Q), and NUTS (P). å å Go to step 15 of the Mates Bed instruction book to complete the assembly of that unit. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Modèle 412091 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 REMARQUE : Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage. Fixer deux RONDELLES D'ESPACEMENT DE CHARNIÈRE (U) et deux CHARNIÈRES (V) à la PORTE ABATTANTE (J). Utiliser quatre VIS TÊTE PLATE 16 mm ARGENTÉES (AA). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (L) dans les gros trous des MONTANTS (C et D).
ÉTAPE 9 ÉTAPE 13 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Il faut peut-être ajuster la PORTE. Suivre les indications cidessous pour ajuster. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément. RÉGLAGES DES PORTES : Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (I).
Modelo 412091 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 NOTA: No apriete los SUJETADORES TWIST-LOCK® por ahora. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije dos ESPACIADORES DE BISAGRA (U) y dos BISAGRAS (V) a la PUERTA ABATIBLE HACIA ARRIBA (J). Utilice cuatro TORNILLOS PLATEADOS DE CABEZA PERDIDA de 16 mm (AA). Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (L) dentro de los agujeros grandes de los PARALES (C y D).
PASO 9 PASO 13 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. La PUERTA puede requerir ajustes. Siga el texto abajo para hacer los ajustes necesarios. AJUSTE DE LA PUERTA: Para ajustar la PUERTA de arriba a abajo (vertical), gire el tornillo de ajuste hacia adentro o hacia afuera.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
