sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Storage Chest Shoal Creek Collection | 412092 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-15 Hammer Français 16-18 Español 19-21 Safety 22 Warranty 23 Page 2 Not actual size Skip the power trip. This time. 412092 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) D BOTTOM (1) G REAR LEG (2) B LEFT END (1) E BACK (1) H FRONT (1) C TOP LID (1) F FRONT LEG (2) I SKIRT (1) G C B E F H G I D A F www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. J2 HIDDEN CAM - 18 K2 CAM SCREW - 18 L ANGLE BRACKET - 4 N LID SUPPORT - 1 O HINGE - 3 R WOOD DOWEL - 2 P BLACK 1-7/8" FLAT HEAD SCREW - 3 Page 4 Q BLACK 9/16" LARGE HEAD SCREW - 24 412092 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eighteen HIDDEN CAMS (J2) into the ENDS (A and B), BOTTOM (D), BACK (E), and FRONT (H). Do not tighten the HIDDEN CAMS in this step. Arrow D J2 E H Arrow J2 (18 used) A Arrow B Arrow J2 Hole www.sauder.
Step 2 å Turn eighteen CAM SCREWS (K2) into the ENDS (A and B) and LEGS (F and G). Remember: Righty tighty. Lefty loosey. (18 used) K2 B A F F G G K2 Page 6 412092 www.sauder.
Step 3 å Fasten the LEGS (F and G) to the ENDS (A and B). Tighten eight HIDDEN CAMS. These surfaces should be even. G S HI urfa DD ce EN wi CA th M S B F F S HI urfa DD ce EN wi CA th M S A G These edges should be even. 1 www.sauder.
Step 4 å å Insert two WOOD DOWELS (R) into the BACK (E). å NOTE: Be sure the WOOD DOWEL in the BACK inserts into the hole in the REAR LEG. Fasten the REAR LEG (G) on the LEFT END (B) to the BACK (E). Tighten two HIDDEN CAMS. These edges should be even. B These holes must be here. G ce rfa Su R E th wi EN DD HI S M CA R 1 Page 8 2 412092 www.sauder.
Step 5 å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS. B These holes must be here. D Un fin ish ed su rfa ce This is a tracking label. Please do not remove. 1 www.sauder.
Step 6 å Fasten the FRONT (H) to the BOTTOM (D). Use three BLACK 1-7/8" FLAT HEAD SCREWS (P). å Fasten the FRONT (H) to the LEFT END (B). Tighten the HIDDEN CAM. å Fasten the REAR LEG (G) on the RIGHT END (A) to the BACK (E). Tighten two HIDDEN CAMS. å NOTE: Be sure the WOOD DOWEL in the BACK inserts into the hole in the REAR LEG. å Fasten the RIGHT END (A) to the FRONT (H) and BOTTOM (D). Tighten three HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day.
Step 7 å Fasten four ANGLE BRACKETS (L) to the SKIRT (I). Use four BLACK 9/16” LARGE HEAD SCREWS (Q). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the SKIRT. Q BLACK 9/16" LARGE HEAD SCREW (4 used in this step) L I ed h is fin n U e ac rf su L L www.sauder.
Step 8 å Fasten the SKIRT (I) to the ENDS (A and B) and BOTTOM (D). Use four BLACK 9/16” LARGE HEAD SCREWS (Q). Q BLACK 9/16" LARGE HEAD SCREW (4 used in this step) I B ed h is n Fi e ac rf su D A Page 12 412092 www.sauder.
Step 9 å å Carefully stand your unit upright. Pro Tip: Lift with your legs. And, you know, your arms. Fasten the HINGES (O) to the BACK (E) and TOP LID (C). Use twelve BLACK 9/16" LARGE HEAD SCREWS (Q). Q BLACK 9/16" LARGE HEAD SCREW (12 used in this step) C E O www.sauder.
Step 10 å Fasten the LID SUPPORT (N) to the TOP LID (C) and BACK (E). Use four BLACK 9/16" LARGE HEAD SCREWS (Q). å NOTE: You will need to lift the front long edge of the TOP LID slightly to fasten the LID SUPPORT. Q BLACK 9/16" LARGE HEAD SCREW (4 used in this step) N C E Page 14 412092 www.sauder.
Step 11 å NOTE: Please read the back page of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 70 lbs. 50 lbs. www.sauder.
412092 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer le DESSOUS (D) à l'EXTRÉMITÉ GAUCHE (B). Serrer deux EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer dix-huit EXCENTRIQUES ESCAMOTABLES (J2) dans les EXTRÉMITÉS (A et B), le DESSOUS (D), l'ARRIÈRE (E) et le DEVANT (H). ÉTAPE 6 Fixer le DEVANT (H) au DESSOUS (D). Utiliser trois VIS TÊTE PLATE 48 mm NOIRES (P).
ÉTAPE 7 ÉTAPE 10 Fixer quatre CONSOLES À ÉQUERRE (L) à la PLINTHE (I). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (Q). Fixer le SUPPORT DE COUVERCLE (N) au COUVERCLE SUPÉRIEUR (C) et à l’ARRIÈRE (E). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (Q). REMARQUE : S'assurer que les chants des CONSOLES À ÉQUERRE sont à fleur du chant de la PLINTHE. ÉTAPE 8 Fixer la PLINTHE (I) aux EXTRÉMITÉS (A et B) et au DESSOUS (D). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (Q).
412092 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el FONDO (D) al EXTREMO IZQUIERDO (B). Apriete dos EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciocho EXCÉNTRICOS ESCONDIDOS (J2) dentro de los EXTREMOS (A y B), el FONDO (D), el DORSO (E) y la PARTE DELANTERA (H). PASO 6 Fije la PARTE DELANTERA (H) al FONDO (D). Utilice tres TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (P).
PASO 7 PASO 10 Fije cuatro SOPORTES ANGULARES (L) al FALDÓN (I). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (Q). Fije el SOPORTE DE LA TAPA (N) a la TAPA SUPERIOR (C) y al DORSO (E). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (Q). NOTA: Asegúrese que los bordes de los SOPORTES ANGULARES estén nivelados con el borde del FALDÓN. PASO 8 Fije el FALDÓN (I) a los EXTREMOS (A y B) y al FONDO (D). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (Q).
WARNING The lid support mechanism is an important safety device. It helps prevent a risk of injury or death to children that can occur if the lid falls on a child’s head or across the back of a child’s neck. ● Make sure you have properly installed the support mechanism. Refer to the instruction booklet, steps 9 through 10. ● Test the lid support mechanism before you use the product. ○ Open the lid at least 2 inches, up to 60 degrees from the closed position (see diagram). ○ Let go of the lid.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
